VIVO STAND-V103F Triple Monitor Desk Stand Instruction Manual

: June 14, 2024
: Vivo

Table of Contents

STAND-V103F Triple Monitor Desk Stand
PACKAGE CONTENTS
ASSEMBLY STEPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Triple Monitor Desk Stand
Instruction Manual

STAND-V103F Triple Monitor Desk Stand

SKU: STAND-V003FGhttps://vivo-us.com/products/stand-v003fg

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products /stand-v003fg
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
NOTE: SOME HARDWARE MAY NOT BE USED
TOOLS NEEDED

PACKAGE CONTENTS

ASSEMBLY STEPS

STEP 1
Install the Pole (A) to the Weighted Base (B) using M6x29mm Screws (S-B). Tighten with a Phillips screwdriver. Slide Pole Cover (C) over Pole (A) to install.

STEP 2
Lay Arm (E) on flat surface with holes for cable clips facing down. Add Plastic Spacers (G) to holes at ends of Arm (E).

NOTE: Transparent monitor arm image used to show cable clip holes. Holes are on the underside of arms and are not visable when arm is facing upright.
STEP 2 – Continued
Align Arm and Arm Extension (D,E) so that the holes for the cable clips are facing down.
Insert Arm (D) into Arm Extension (E) as shown below. Secure using M10x47mm Screws (S-A) and 6mm Allen Wrench (T-C).

NOTE: Transparent monitor arm image used to show wire clip holes. Holes are on the underside of arms and are not visible when arm is facing upright.
Press Joint Covers (F) onto the top and bottom of arm joints. Place Cable Clips (J) into cable clip holes.

STEP 3
Slide arm assembly onto Pole (A) at desired height and secure using M8x10mm Screws (S-C) and 5mm Allen Wrench (T-B).

STEP 4
Option A – Flat Back Monitors
Attach the Center VESA Plates (H) to the monitors you intend to mount in the center of the mount. Attach Side VESA Plates (I) to remaining monitors. Secure using M4x12mm Screws (M-A).

NOTE: Hand tighten screws to avoid stripping the plastic screw heads.
Option B – Curved Monitors
Attach the Center VESA Plates (H) to the monitors you intend to mount in the center of the mount. Attach Side VESA Plates (I) to remaining monitors. Secure using M4 Spacers (M-C), M4x30mm Screws (M-B) and a Phillips screwdriver.

STEP 5
Slide the center monitor onto the Center Head (D1) of arm assembly. Install M4x6mm Screws (S-F) to secure the monitor.

STEP 6
Slide the outer monitors onto Outer VESA Heads (E1). Secure with Cap Nut (S-E).

Adjust Monitor Tilt
Pry off Plastic Covers (E2) from the Outer VESA Heads (E1). The exposed nut on the side is used to adjust the tilt. Tighten the nut using Wrench (T-D) to adjust. Replace Plastic Covers (E2).

To adjust center monitor swivel or tilt, use 3mm Allen Wrench (T-A) to loosen center set screw on the Center Head (D1), as shown at left.

Adjust Monitor Height
To adjust center monitor height, turn the screw behind Center Head (D1) using the 5mm Allen Wrench (T-B).

To level the side monitors, remove the Cap Nut (S-E) and turn the inner bolt with the 3mm Allen Wrench (T-A) to raise or lower the monitor. Replace Nut after the adjustment.
Cable Management
Manage cables using Cable Clips (J) on assembled arms. Remove the split cap from the Pole (A) and feed cables through, pulling ends out from the opening in back. Replace the split cap when finished.

Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
LAST UPDATED: 11/07/2023 REV2
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com