GRID DDU5 Dashboard Display Unit Instruction Manual
- June 14, 2024
- Grid
Table of Contents
GRID DDU5 Dashboard Display Unit
BEFORE YOU START
Thank you for your purchase. In this manual we will provide you with the means to get started using your new dash!
GRID DDU5
-
Features
-
5” 854×480 VOCORE LCD 20 full RGB leds
-
Up to 30 FPS
-
24 bit Colors
-
USB Powered
-
Multiple software options Drivers included
-
Mounting the dash is very easy thanks to the included mounting brackets. We offer a wide range of support for most popular hardware. In this manual we only display the two mounting brackets included with the dash. Please review our website to determine which mounting bracket fits your hardware.
Mounting the dash
- To be able to mount the dash on the hardware of your choice, we provide several mounting brackets. Which ones you have received may depend on your purchase and may be different from the following ones we show. However, mounting is all more of the same. With the instructions for the two included brackets, you should be able to mount any specific ones for your hardware.
OSW/SC1/VRS
- Remove the existing upper bolts which hold the motor in place. Re-use these bolts and washers to fix the mounting bracket to the front mount.
Fanatec DD1/DD2
- Locate the accessory mounting holes on your Fanatec hardware and use the two bolts (A4) and washers (A6) from our supplied hardware kit.
Installing drivers
To make the display part of the dash functional, specific drivers are needed. Drivers can be downloaded from the product page.
Vocore drivers download
Installation
- To install the display drivers, run the downloaded package and specify the location where to install the drivers:
-
Specify the name of the start menu folder
-
Review the settings before installation
- The drivers will install now. Sometimes this can take longer than expected. This usually means a system restore point is being made and should not hinder installation.
- If it does, unplug the USB cable to the Dash in case it is connected and try again. Make sure you have administrator rights on your system.
RaceDirector installation
- To control the dash, Race Director can be used. This is a simple but effective piece of software, purpose built for our own hardware.
- Download the latest version of Race Director from: http://www.grid-engineering.com/srd-setup
- Please review the manual found at: http://grid-engineering.com/srd-manual
- For more advanced users, Simu can also be used, but this manual will focus on our own software.
- Download the latest version of Simu from https://simhubdash.com
Installation
- Unzip the downloaded file ‘RaceDirector.zip’ and extract the folder to a location of your choice, run the installer to start the installation.
- If you encounter a Windows Defender/Smart Control screen warning you of only software of trusted sources, please press ‘Run anyway’. This warning will dissapear when more and more people start busing Redirector and the software has been proven safe for use.
- Specify the location where to install the software
Make sure all options are checked
- RaceDirector will be installed
Race Director configuration
- The very first time launching RaceDirector, you will probably be greeted with an empty screen and booting might also take a bit longer than you would expect.
- Don’t worry, this is normal, some additional files might be downloaded/updated. To keep things visually clear and clutter free, we only want to show the options you actually need.
- Press the ‘Gear’ symbol to enter the settings page. To keep the interface clutter free, the device(s) you own need to be activated.
- In this case we tick the box for the ‘Porsche 911 GT3 Cup Display Unit’.
- The ‘device icon’ is activated now and once we press it, the device page will be shown.
Firmware
- We recommend to make sure your device has been flashed with the latest firmware. If you do NOT see orange the ‘Flash device’ (1) button, you are good to go. If you do see this button, press it and follow instructions on screen.
Configuration and settings
- Almost all of the options found here speak for themselves, though for the sake of being complete, we will go over them on by one.
- For more detailed information about the functionality we offer within Redirector, please read the Redirector manual. We go into more detail in there, as we prefer to keep the product manuals as easy to read as we possibly can.
-
‘LED profile name’ (1)
This serves two purposes in one. Firstly the name of the loaded profile is noted to verify that the profile has been loaded. Secondly the name is used when saving the profile. -
Save profile’ (2)
When you want to save an excisting profile, press this button. You will be warned that the profile is an excisting profile, thus overwriting it will change it from the default settings. Alternatively, once the profile name (see above) has been changed, that name will be used as the new profile name. -
‘Load profile’ (3)
This loads the selected profile in the drop down menu. -
Test LEDs’ (4)
This opens up a pop-up window where you use test input to see what the LEDs do using the currently loaded profile. -
Select dash’ (5)
This allows you to select a standard dash for a given car. We do not support all cars in every sim. The chosen dash will also be visually shown on the visual representation of the hardware. -
Select display’ (6)
This will make sure the chosen dash is rendered on the correct screen. If you don’t get any picture, be sure to follow the instructions on Page 6 of this manual. -
Record trackmap’ (7)
This will allow you to record a trackmap of the track you are driving. This will be used by dashes which have a GPS page where you can track the positions of drivers on track. When no data has been recorded, the track will be rendered as a simple loop. Stop short of start/
finish on track, tick the tickbox and drive a lap in the middle of the track with a constant speed. After start/finish the record function is automatically disabled, the track will display as recorded on the appropriate page(s). -
AVG fuel laps’ (8)
This value determines how many laps are used to calculate average fuel usage. The average is reset every time you enter the pits to keep the average a meaningful number. -
Low fuel amount’ (9)
This number (in liters) will be used for the dash to know when to activate the ‘Low Fuel’ function, alarm or warning. -
Redline flash color’ (10)
You can pick the color when you reach the redline or optimal shift point. Right now this is preset at a standard 95%. -
Next page’ (11)
Cycle to the next page of the loaded dash. Select a controller of your choice, press ‘Select button’ and you have about 10 seconds to press the button you want to use. -
Previous page’ (12)
Cycle to the previous page of the loaded dash, works like described above.
Note : when the page controls are configured, they won’t affect a dashboard unless a sim is running.
LED settings
The LEDs can be changed by simply pressing the LED to be changed and
changing its function or color. Here is the LED numbering for reference.
- There should be enough info in the provided default LED profiles to be able to adjust LED settings to your liking. To start building your own profile, we suggest to copy an existing one and change where needed. The advantage is you always have a backup of the default profile to fall back to.
- We do recommend to read the RaceDirector manual for detailed information on functions, settings and basic rules for the LED settings.
Bill of materials
IN THE BOX
#
| Part| QTY|
Note
A1| Dash DDU5| 1|
A2| USB B-mini cable| 1|
A3| Bracket Fanatec DD1/DD2| 1|
A4| Bracket OSW/SC1/VRS| 1|
A5| Bolt M6 X 12 DIN 912| 2| Used with Fanatec
A6| Bolt M5 X 10 DIN 7380| 4| To fit mounting bracket to dash.
A7| Washer M6 DIN 125-A| 4|
A8| Washer M5 DIN 125-A| 4|
Disclaimer : for some entries on this list, we supply more than
required as spare materials. Don’t worry if you have some leftovers, this is
intentional.
More information
If you still have some questions regarding assembly of this product or about
the manual itself, please refer to our support department. They can be reached
at: support@sim-lab.eu
Alternatively, we now have Discord servers where you can hang out or ask for
help. www.grid-engineering.com/discord
Product page on the GRID Engineering website
Documents / Resources
| GRID
DDU5 Dashboard Display
Unit
[pdf] Instruction Manual
DDU5 Dashboard Display Unit, DDU5, Dashboard Display Unit, Display Unit
---|---
References
- grid-engineering.com/srd-manual
- GRID
- grid-engineering.com/drivers-vocore
- GRID DDU5 Dashboard Display Unit
- grid-engineering.com/srd-setup
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>