Trail Grid Pro: Install Toyota 4Runner Raptor Lights with Instruction Manual
- June 3, 2024
- TRAIL GRID PRO
Table of Contents
The Trail Grid Pro 4RUN-RAPTOR-WHITE-14-21 Toyota 4Runner Raptor Lights Instruction Manual provides step-by-step instructions for installing Raptor lights on your Toyota 4Runner. The kit includes everything you need to install the lights, and the instructions are easy to follow, making it a simple DIY project. The manual includes a QR code that links to a video tutorial, which can be used as a reference during the installation process. The kit no longer requires routing wires through the firewall, simplifying the installation process even further. The instructions cover each step of the installation process, from crimping the ring terminal to the black wire to connecting all four lights to the provided wiring harness. The manual also includes information about alternate fuse locations and securing the ring terminal from the black wire to the 10mm ground bolt. With this instruction manual, you can install Raptor lights on your Toyota 4Runner and enjoy enhanced visibility on the road.
TRAIL GRID PRO 4RUN-RAPTOR-WHITE-14-21 Toyota 4Runner Raptor Lights
Raptor Light Install Supporting Documentation
UPDATE: Use the video as a reference but the new kit no longer requires the routing of wires through the firewall.
Full Raptor Light Install Video QR Code
Scan the QR code below to access our install video or visit our YouTube
Channel here: https://youtu.be/_G6NCpBN6pE
Included In Your Raptor Light Kit
Step 1: Crimp the ring terminal to the black wire. Crimp the add-a-fuse to
the red wire. Ensure a snug connection by pulling gently on your wires. Using
a heat gun, you may also heat up and shrink the insulation on the ring
terminal and butt connector to further secure the
wires.
Step 2: Insert the Raptor Lights into the desired locations on your
grille. Insert the wire end through the hole first and gently push the light
into place. If the light doesn’t seem to be secure, try rotating the light 180
degrees. The tabs should all lock into place.
Repeat for all 4 lights.
Step 3: Connect all 4 lights to the provided wiring harness. The connections are keyed and will only connect one way. Route the power and ground wire behind the driver’s side headlight and toward the fuse panel located behind the battery.
Step 4: Install add-a-fuse into the INJ fuse located in the fuse box under the hood near the driver-side fender. Remove the 10 amp fuse that is located in the INJ location and place into the empty slot on the add-a-fuse. Place the add-a-fuse back into the INJ fuse location.
NOTE: Alternate fuse locations (EFI No.2, H-lp LH, H-lp RH) You may choose to cut a small notch in the bottom the fuse box lid so that the fuse cover will close tightly without smashing the red power wire. Secure the ring terminal from the black wire to the 10mm ground bolt. It is located near the battery on the inside of the driver’s side fender.
SPECIFICATION
Product Name| TRAIL GRID PRO 4RUN-RAPTOR-WHITE-14-21 Toyota 4Runner
Raptor Lights
---|---
Installation Type| DIY
Compatibility| Toyota 4Runner (2014-2021)
Installation Difficulty| Easy
Supporting Documentation| Raptor Light Install Instruction Manual and
Video Tutorial
Installation Process|
- Crimp the ring terminal to the black wire and add-a-fuse to the red wire
- Insert the Raptor Lights into the desired locations on the grille
- Connect all 4 lights to the provided wiring harness and route the power and ground wire behind the driver’s side headlight and toward the fuse panel located behind the battery
- Install add-a-fuse into the INJ fuse located in the fuse box under the hood near the driver-side fender
- Secure the ring terminal from the black wire to the 10mm ground bolt located near the battery on the inside of the driver’s side fender
Additional Information| Alternate fuse locations (EFI No.2, H-lp LH, H-lp RH). It is recommended to cut a small notch in the bottom of the fuse box lid so that the fuse cover will close tightly without smashing the red power wire.
FAQS
What is the Trail Grid Pro 4RUN-RAPTOR-WHITE-14-21 Toyota 4Runner Raptor Lights Instruction Manual?
The Trail Grid Pro 4RUN-RAPTOR-WHITE-14-21 Toyota 4Runner Raptor Lights Instruction Manual provides step-by-step instructions for installing Raptor lights on your Toyota 4Runner.
What is included in the Raptor Light Kit?
The Raptor Light Kit includes everything you need to install the lights.
Is the installation process difficult?
No, the instructions are easy to follow, making it a simple DIY project.
Is there a video tutorial available for reference during the installation process?
Yes, the manual includes a QR code that links to a video tutorial.
Does the new kit still require routing wires through the firewall?
No, the new kit no longer requires routing wires through the firewall.
What is the first step in installing the Raptor lights?
The first step is to crimp the ring terminal to the black wire.
How do I ensure a snug connection when crimping the wires?
Ensure a snug connection by pulling gently on your wires. Using a heat gun, you may also heat up and shrink the insulation on the ring terminal and butt connector to further secure the wires.
How do I insert the Raptor Lights into the desired locations on my grille?
Insert the wire end through the hole first and gently push the light into place. If the light doesn’t seem to be secure, try rotating the light 180 degrees. The tabs should all lock into place.
How do I connect all 4 lights to the provided wiring harness?
Connect all 4 lights to the provided wiring harness. The connections are keyed and will only connect one way. Route the power and ground wire behind the driver’s side headlight and toward the fuse panel located behind the battery.
Where do I install the add-a-fuse?
Install add-a-fuse into the INJ fuse located in the fuse box under the hood near the driver-side fender.
Is there an alternate fuse location available?
Yes, alternate fuse locations (EFI No.2, H-lp LH, H-lp RH) are available.
How do I secure the ring terminal from the black wire to the 10mm ground bolt?
Secure the ring terminal from the black wire to the 10mm ground bolt. It is located near the battery on the inside of the driver’s side fender.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>