VIVO MOUNT-POLEKB Black Pole Mount Tilting Keyboard Tray Instruction Manual
- June 14, 2024
- Vivo
Table of Contents
VIVO MOUNT-POLEKB Black Pole Mount Tilting Keyboard Tray
Product Information
- Product Name: Black Pole Mount Tilting Keyboard Tray
- SKU: MOUNT-POLEKB
- Manufacturer: VIVO
- Website: https://vivo-us.com/products/mount-polekb
- Contact Information:
- Phone: 309-278-5303
- Email: help@vivo-us.com
- Website: https://vivo-us.com
Product Usage Instructions
WARNING!
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Package Contents
The package includes the following items:
- (x1) Arm
- (x1) Right Tray
- (x1) Left Tray
- (x1) Connecting Plate
- (x1) Mouse Pad
- (x1) Wrist Pad
- (x1) Cable Clip
- (x4) M4x8mm Screw
- (x4) M4x12mm Screw
- (x4) M4 Nut
- (x2) M8x70mm Screw
- (x1) 6mm Allen Wrench
- Phillips Screwdriver
- (x1) Wrench
NOTE: SOME HARDWARE MAY NOT BE USED DO NOT EXCEED WEIGHT CAPACITY.
- Weight Capacity: 2.2lbs (1kg)
- Failure to adhere to weight capacity may result in serious injury.
Assembly Steps
-
STEP 1 (Option A)
For poles with a diameter of 28mm-45mm: -
Loosen the bolts on Arm (A) using the 6mm Allen Wrench (T-A).
-
Slide Arm (A) onto the pole.
-
Tighten the bolts using the 6mm Allen Wrench (T-A).
-
Apply Cable Clip (G) to Arm (A).
-
STEP 1 (Option B)
For poles with a diameter of 46mm-60mm: -
Swap the pre-installed bolts (A1) with the M8x70mm Screws (S-D) using the 6mm Allen Wrench (T-A).
-
Slide Arm (A) onto the pole.
-
Tighten the M8x70mm Screws (S-D) using the 6mm Allen Wrench (T-A).
-
Apply Cable Clip (G) to Arm (A).
-
STEP 2
Attach Left Tray (C) and Right Tray (B) with Connecting Plate (D) using the M4x8mm Screws (S-A) and a Phillips screwdriver. -
STEP 3
Attach Tray Assembly to Arm (A) using the M4x12mm Screws (S-B), M4 Nuts (S-C), Wrench (T-B), and a Phillips screwdriver. -
STEP 4
Remove the protective film from Wrist Pad (F) and place it onto the front of the tray assembly. Place Mouse Pad (E) onto the tray assembly. -
STEP 5
Adjust the tilt joint with the 6mm Allen Wrench (T-A). Route cables through Cable Clip (G) and adjust as desired.
For any further assistance or to report damaged or defective parts, please contact VIVO’s support team.
Support Contact Information:
- Phone: 309-278-5303
- Email: help@vivo-us.com
- Website: https://vivo-us.com
We strive to provide prompt assistance with an average resolution time of 5 minutes and 4 seconds during office hours.
For more VIVO products, please visit our website: https://vivo-us.com
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
ASSEMBLY STEPS
-
STEP 1 (Option A)
28mm-45mm Diameter Poles- Loosen the bolts on Arm (A) using 6mm Allen Wrench (T-A) and slide onto the pole.
- Tighten bolts using 6mm Allen Wrench (T-A). Apply Cable Clip (G) to Arm (A).
-
STEP 1 (Option B)
46mm-60mm Diameter Poles- For pole sizes larger than 45mm, swap pre-installed bolts (A1) with M8x70mm Screws (S-D) using 6mm Allen Wrench (T-A) and slide Arm (A) onto the pole.
- Tighten M8x70mm Screws (S-D) using 6mm Allen Wrench (T-A). Apply Cable Clip (G) to Arm (A).
-
STEP 2
- Attach Left Tray (C) and Right Tray (B) with Connecting Plate (D) using M4x8mm Screws (S-A) and a Phillips screwdriver.
- *UNDERSIDE VIEW SHOWN
NOTE: The Notch in Connecting Plate (D) should be facing the back of the Keyboard Tray pieces.
-
STEP 3 Attach Tray Assembly to Arm (A) using M4x12mm Screws (S-B), M4 Nuts (S-C), Wrench (T-B), and a Phillips screwdriver.
-
STEP 4 Remove protective film from Wrist Pad (F) and place onto the front of the tray assembly. Place Mouse Pad (E) onto the tray assembly.
-
STEP 5 Adjust the tilt joint with 6mm Allen Wrench (T-A). Route cables through Cable Clip (G), and adjust as desired.
ABOUT COMPANY
-
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
-
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S -
www.vivo-us.com
AVG. RESOLUTION TIME (within office hrs): < 15 M -
help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
-
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Black Pole Mount Tilting Keyboard Tray – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>