K F CONCEPT DQ202 Solar Powered Wireless Security Camera User Guide

: June 14, 2024
: K F CONCEPT

K F CONCEPT DQ202 Solar Powered Wireless Security Camera User Guide

Product List

Product Display

Charging

Tip: When using the product for the first time, please use DC 5V-1A/2A adapter to fully charge the product.
There are two options to generate the daily power supply: () Use a DC 5V-1A/2A adapter to charge the battery (2) Charge the battery with the solar panel

Connection Devices

Use your mobile phone to download and launch the K&F CAM applica-tion and follow the on-screen instructions to complete the network configuration.

Download APP:

Search for “K&F Cam” in the App Store

Supporting devices: Smartphones, excluding pad. Supporting systems: Andorid 4.3 and above, i0S 9. X and above.

Tip: Allow APP to use the mobile network during installation

2. Register and log in account number:
Please register your account with your mailbox

Add device:

(@ Connect the mobile phone to the wifi, and keep the mobile phone and device close to the router. The device only supports connection to
2.4 GHz wifi, not 5G wifi.

Click “Add Device” on the APP, select “Battery Camera’, and continue adding according to the APP guide.

Prompt for a connection failure:

Make sure your mobile phone is connected to 2.4 GHz wifi instead of5G wifi.
Make sure you have entered the correct wifi password, especially when the password contains special characters.
Please check that there are no special characters in the wifi password, such as */1~@#”.
Don’t shake your mobile phone when scanning the QR code, and keep a distance of 10-15cm between the mobile phone and the lens. 5. Restart the device and try again 6. Please contact customer service at security@kfconcept.com if attempts to connect remain unsuccessful 7.Or feed back your problem in the App: “My”>”Help and Feedback”>”My Device”

Device installation

Take the device to the location where it needs to be installed, open the APP to see if the monitoring picture is smooth. If it is, prepare for installation. 2. Install the device at a height of 2-3 meters above the ground (the installation position should not be at a 90°angle with the road ahead) s0 as to maximize the effectiveness of the infrared sensor

Tip: If a moving object approaches the PIR sensor vertically, the camera may not be able to detect its motion.

Camera installation

Install solar panels to ensure that the solar panels are at a right angle to receive sufficient sunlight

Turn on the message push no

(DReceive alarm notification

.PIR sensor detection type irst open the motion detection button

2Then select the object you want to detect. There are two choices: human body detection/moving object detection (The default mode is the human body detection when it is turned on).

Human body detection mode Moving object detection mode

PIR sensitivity setting allowable

give more false alarms. It is recommended that you set the sensitivity to a “low” or “medium” level when installing your camera outdoors.

3. Sound-light alarm setting

Set the sound and light alarm. After this function is turned on, the device can actively drive away intruders. The sound-light alarm only operates at night.

I. Functions

Enter settings menu (alarm settings,video, lighting, device information firmware upgrade, etc)

Turn on/off the speaker
Video definition settings (SD, HD options)
Full screen option
sD card video playback
Cloud storage video playback
WiFi signal strength

Setting module

Storage function

If you want to view the historical pushed video on the APP, you have two options: SD card storage/cloud storage SD card storage: Insert an SD card supporting classi0 standard, with a maximum storage capacity of 128G. Cloud storage: By subscribing to secure and encrypted cloud services,
you can enjoy the cloud storage service. Before subsci enjoy a free trial period of 7 days.

Troubleshooting

The camera doesn’t work

Make sure the power switch is turned on and use the DC 5V-1A/2A power adapter to charge the battery.
2. Connection problems
(ICheck whether the device is in an energized state and observe whether the working indicators of the device are on normally. (@ Check whether the wifi is normal, restart the router. @ The device is too far away from the router to receive a good wifi signal. It is recommended to shorten the router distance, or add the device again after increasing a wifi amplifier. @If the router or wifi password is changed, please delete the device first and then add it again. ®)If you can’t view the video remotely, please ensure that the network signal of your mobile phone is good.
3. Cannot open historical video
(@You need to insert a FAST 32 Class 10 SD card, which supports
8G-128G, and restart the device after insertion.
The SD card is broken and needs to be replaced.
(@)Check the SD card status in Settings to ensure that the SD card has
been successfully identified.
Poor network leads to unsuccessful identification.
If you still have problems after the above troubleshooting methods, please contact security@kfconcept.com

Technical specifications

X. FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Partls of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and onthe user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.
.increase the separation between the equipment and receiver

connected.

3.Consult the dealer or an experienced radio/TV technician for help.
4.This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference
(2)This device must accept any interference received, including interference that may cause undesired operation. RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm the radiator of your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
FCC ID: 2AYIN-DX20X

To improve the user experience, our APP may be updated from time to time. Please follow our updates.
If you need any technical help in the process of using the APP, please contact us as using the following options, we will be available to solve your problem within 24 hours.
1. Email us at security@kfconcept.com. 2. Provide feedback on the “Message” page of the APP.
3. Visit our official website at www. kfconcept.com for more support.