K F CONCEPT P-10.08.03.0281-02 Nano-X PRO Filter Holder System Kit for Plate Filters User Manual

June 14, 2024
K F CONCEPT

Square Filter System PRO
INSTRUCTION

P-10.08.03.0281-02 Nano-X PRO Filter Holder System Kit for Plate Filters

K F CONCEPT P 10.08.03.0281 02 Nano X PRO Filter Holder System Kit for Plate
Filters - Figure

Component description

K F CONCEPT P 10.08.03.0281 02 Nano X PRO Filter Holder System Kit for Plate
Filters - Description

① CPL bin switch handle
② Square filter guide block
③ CPL bin cover| ④ CPL bin
⑤ CPL dial wheel
⑥ Adapter rings locking button| ⑦ Adapter ring
⑧ Square filter
⑨ CPL
---|---|---

Installation of filter bracket

2.1 Tightening the adapter ring with screw thread side onto the front of your lens;

  • The caliber of the filter holder adapter ring should be the same as the front of your lens. If you have multiple lenses with different calibers, you can contact your dealer to purchase separate adapter ring to fit the lens you need. 2.2 First, insert the adapter ring into the slot at the upper right of the rear port of the filter holder, meanwhile loosen the adapter rings locking button and pull it to lower left, then push the adapter ring into the rear port of the filter holder and release the lock  button;K F CONCEPT P 10.08.03.0281 02 Nano X PRO Filter Holder System Kit for Plate Filters - Open and close 2.3 To lock the adapte ring by rotating the lock button clockwise thoroughly. If you need to rotate the filter holder during the shooting process, loosen the lock button counterclockwise a little.K F CONCEPT P 10.08.03.0281 02 Nano X PRO Filter Holder System Kit for Plate Filters - Lock and Unlock

Installation of CPL

3.1 Installation procedure

  1. Push the CPL bin switch handle towards left;
  2. Open the CPL bin cover by cunterclockwise;
  3. Insert the CPL into the CPL bin with correct orientation;
  4. Close the CPL bin cover by clockwise, til hearing a click, that is finished;
  5. Rotating the CPL adjusting wheel on the left of the filter frame can adjust the angle of CPL to eliminate reflection.
    *Please repeat the above motions when removing the CPL.

K F CONCEPT P 10.08.03.0281 02 Nano X PRO Filter Holder System Kit for Plate
Filters - Procedure

3.2 Note: The CPL is directional, so please pay attention to the direction when installing the CPL. The filter holder and the CPL frame have fool proof design. The CPL bin cover cannot be closed if the CPL is installed inversely, when it happened please check  whether the CPL is installed upside down. If the state after closing the CPL bin cover is like the pictures , it means the CPL is inverted. Please take it out and reinstall in a different direction

Installation of Square filter

4.1 How to install the square filter on the filter holder

  1. Insert the square filter with frames into the filter holder slot with the text surface outwards;
  2. Adjust the position of the filter up and down to control the effect on the image;
  3. If you need to use multiple square filter overlays, please insert the adjacent square filter into the guide block by reversing 180 degrees to facilitate the removal and adjustment of the filter;

K F CONCEPT P 10.08.03.0281 02 Nano X PRO Filter Holder System Kit for Plate
Filters - Filter holder 4.2 How to assemble the protection frame for Square filter

  1. Please wear gloves or use a cleaning cloth to wrap the filters when assembling, to prevent greasy dirt on the glass;
  2. First, install the two side frarnes A on the square filter;
  3. There is a installation buckles on each side of the top frame B and the bottom frame C, please insert the buckle with the corresponding hole site at both ends of each side frame A, then the assembly is finished.
    Note: Please keep the text surfaces of the top frame and bottom frame facing the same side while assembling, lest using effect.

K F CONCEPT P 10.08.03.0281 02 Nano X PRO Filter Holder System Kit for Plate
Filters - Square Filter

Designed byK F CONCEPT P 10.08.03.0281 02 Nano X PRO Filter Holder
System Kit for Plate Filters - logo 2

-2 years free warranty period is covered. Please register on www.kfconcept.com to extend warranty period for your products, where you can also obtain further product information,using manual and maintenance instructions.

Shenzhen Zhuo Er Photographic Equipment Co., LTD
Address: 3rd Floor, Ist Building, Mengliyuan Industrial Park, No.146 Yousong Road,
Longhua Street, Longhua District, Shenzhen City,
Cuangdong Province, China
Importer: Cross Global GmbH
Address: Kraeling weg 2, 60435, Frankfurt

K F CONCEPT P 10.08.03.0281 02 Nano X PRO Filter Holder System Kit for Plate
Filters - qr codehttps://www.kfconcept.com/
Please Scan for More Information
Made In China

Documents / Resources

| K F CONCEPT P-10.08.03.0281-02 Nano-X PRO Filter Holder System Kit for Plate Filters [pdf] User Manual
P-10.08.03.0281-02 Nano-X PRO Filter Holder System Kit for Plate Filters, P-10.08.03.0281-02, Nano-X PRO Filter Holder System Kit for Plate Filters, System Kit for Plate Filters, Plate Filters
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

K F CONCEPT User Manuals

Related Manuals