K F CONCEPT B0CFZXH1ZK WiFi Trail Camera Instruction Manual

K F CONCEPT B0CFZXH1ZK WiFi Trail Camera

Package Check list

1. Wildlife camera; 2. Mounting strap; 3. Tree nail bracket;
2. USB cable (USB2.0); 5. Instructions; 6. Quick Operation Guide

Caution

1. Please tear off the protective film on the camera lens and PIR sensor before use.
2. Eight 1.5 V AA alkaline batteries or lithium batteries shall be installed before use. Caution: Ban mixing new batteries with old ones or mix the battery types.
3. Ordinary rechargeable AA batteries are not recommended, because the low voltage generated will cause operational problems. Using standard 1.5 V rechargeable AA batteries.
4. Batteries shall be removed when the camera is not in service.
5. In order to save photos and videos, SD memory card (Note: please use class 10 or above), must be inserted into the memory card slot. Please insert the SD card when the camera is in OFF mode. Caution: format the SD card when using the camera for the first time.( SD memory card capacity shall be within 512 GB).
6. The screen only be opened in the TEST mode to change the menu settings, view the photos and videos taken.
7. Connect the hunting camera via mini USB (USB2.0), the data can be displayed to the computer.
8. Please mount the camera at a height of 1 – 2 m with straps or tree nails, adjust best field of vision.

Product Introduction

Information of the K &F Concept trail camera

The Wifi wildlife camera is a wildlife observation camera with an infrared sensor that can detect the change of ambient temperature in the detection area. When animals enter the area, the camera can be activated to take photos or record videos, and the recorded photos and videos can be viewed through the mobile APP.

Structure of the camera

1. PIR sensor;

2. LED infrared light;

3. Lens;

4. Working light;

5. Locking buckle;
   
   

6. MENU;

7. REPLAY;

8. SHOT;

9. OK;

10. VIDEO/UP;

11. /12. (Left and right)SELECT;

12. PHOTO/DOWN;

13. Loudspeaker;

14. SD card slot;

15. USB interface;

16. TEST;

17. Battery jar;

18. 6V 1.5A Power interface;

19. Fixed port;

20. Screen.

Camera Operation

Installation of the battery

As shown in the images, open the camera locker, the battery jar is on the right part of the camera. Pull the rope at the top of the battery jar first, open the battery protective cover, install 8 new 1.5V AA batteries, and then close the protective cover. Checking the positive and negative directions of each battery are correct.

Note: Disposable AA alkaline batteries or lithium batteries are recommended. Never mix new batteries with old ones. Rechargeable AA batteries are not recommended, because most rechargeable batteries cannot reach the voltage of 1.5V.

Insertion of memory card

It is necessary to insert a memory card to save photos and videos. 32 GB to 128 GB SDHC/SDXC memory cards are recommended. Please insert the SD card into the memory card slot before startup. Please check whether the memory card protection setting is activated before inserting the SD card (as shown in the figure);

Insert the memory card as shown in the figure, push the memory card into the card slot, and a “snap” sound indicates that the memory card is in place;

When taking out the memory card, press the memory card and push it inward. When you hear a “snap” sound, the memory card will be partially ejected and then it can be taken out.

Caution: Only the SD memory card with standard size can be used. Micro SD cards with an adapter cannot be used. Please use the SD card of Class 10 or above, with a maximum capacity of 512 GB.

External power supply

The camera can be connected to an external power supply, and a 6V2A external power supply is required.
Please use a DC connector with an outer diameter of 3.5 mm and an inner diameter of 1.35 mm.

Installation of fixing device

• Install straps: Fix the camera to a tree or other object with the attached strap, place the camera as needed, and pull the loose end of the fixing strap until the camera is firmly fixed.
  

• Install tree nails: Fix the camera on the tree with the attached tree nail, and the interface of the tree nail is of 1/4″ x 20 thread, as shown in the figure
  

Schematic diagram of startup operation

Open the locker; Uncover the battery protection cover; Put in the battery; Confirm the memory card; Insert memory card;
Open the TEST mode; Enter the system menu; Select “Format the memory card” and then click OK.

Connect the camera and mobile APP “Trail Camera WiFi”

Scan the QR code below, or search for “Trail Camera Wifi” in Apple APP Store/Google Play to download the APP. Please keep the Bluetooth on. Note: WIFI visual distance is 20m, and Bluetooth connection distance is 20m.

Connection steps

Step 1: Turn on WiFi on your phone, turn on Bluetooth, and open the “Trail Camera Wifi” APP

Step 2: Switch the device to ON mode, select the camera on the mobile client, enter the password, and connect the mobile phone and the camera

Step 3: Enter the password 12345678 and click OK, it will prompt that Bluetooth is being connected

Step 4: It will prompt you to connect to the camera on the APP, the APP will connect to your camera through WLAN network, and then click Connect. The mobile APP has entered the preview interface, and PHOTO mode defaults.

Camera Settings

The camera can start working once the battery and SD card are putting in and WiFi on the phone is connected.

Before using the camera, please change the settings as your need, which a TEST mode is available. Under this mode, in addition to the change of settings, you can also view photos and videos taken.

Mode switch

“OFF” mode: An initial mode, under which, the camera can be shut down;
“TEST” mode: This mode can be used to set up the camera or view the photos and videos taken;
“ON” mode: Under this mode, the camera will enter the working state and operate according to the set parameters.

Introduction to keys

Turn the mode switch to TEST mode and the camera will be turned on;

Use the operation key. The following operation keys are provided on both sides of the display panel:

Switch to VIDEO (in TEST mode)
Down| “Down” (in MENU mode); View the next photo/video (in REPLAY mode); Switch to PHOTO (in TEST mode)
Left| Left navigation (MENU mode)
Right| Right navigation (MENU mode)
SHOT| Start photo taking/video recording ( in TEST mode )
OK| Start / stop playing video files ( PLAY mode );
OK / Enter (in MENU mode)

Description of function settings

In TEST mode, press the MENU key to call the menu, which lists all the menu options and RECORDING mode values of the camera.

camera will take photos or record videos; in “PHOTO + VIDEO” mode, the camera will take photos before recording
Photo resolution| 32MP24MP16MP12MP；8MP5 MP (default)| The higher the resolution, the better the photo quality, and the more storage space required
Continuous photo taking|

1. photo (default);
2. photos; 3 photos; 10 photos

| Select the number of photos taken when the camera is triggered in the PHOTO mode
Video resolution| 38402160@10fps
2304×1296@30fps
1920×1080@30fps
1280×720@30fps
(default) 720×480@30fps
640×480@30fps| Video resolution is optional
Time-lapse video resolution| 8MP (3840 2160); 3MP (23041296); 5MP (30721728) (default)| Time-lapse video resolution is optional
Video duration| 10 s (default); Minimum 3 s, maximum 10 min| Video length is adjustable
Sound recordings| ON (default); OFF| Choose whether to record video with sound or not
Motion sensing delay| 30 s (default); Minimum 2 s, maximum 60 min| The interval between two triggers, the camera will not record any images and videos during the time interval. Note: With a short interval, the camera shoots more frequently and the battery consumption will be higher.
Monitoring period| ON (time setting); OFF (default)| You can set the camera to work only in one time period, and the camera will not be triggered in other periods, and will not take any photos and videos.
Time-lapse Shooting| Normal；TL video :Off (default)| When on, the camera will automatically take photos/videos at selected intervals regardless of whether the PIR senses motion.

Note: In this mode, the PIR stops working.

Languages| 13 languages are available, and English is the default one| Language Settings
Motion sensing sensitivity| Low; Medium (default); High| The higher sensitivity means more sensitive sensing, and the battery consumption also increases. It is recommended to set the sensitivity to medium or high when shooting small animals with a fast moving speed. When shooting large animals, the sensitivity can be set to low or medium.
Loop recording| ON; OFF (default)| After this function is turned on, the earliest filewill be overwritten according to the shooting time when the memory card storage space is insufficient,and when it is not turned on the camera will stop shooting when the memory card storage space is insufficient.
Loop recording| The time format can be 24-hour or 12-hour time system, and the date format can be dd-mm-yyyy, yyyy-mm-dd or mm-dd-yyyy| After this function is turned on, the earliest filewill be overwritten according to the shooting time when the memory card storage space is insufficient,and when it is not turned on the camera will stop shooting when the memory card storage space is insufficient.
Photo tagging| Time and date (default); OFF| Time and date can be printed on the photos
Automatically turn off WiFi| Auto WiFi turn-off if no operation within 1 min / 3 min (default) / 5 min| Set the time to turn off wifi automatically
WiFi name| The WiFi name is GcamproXXXX|
WiFi password| Default password is 12345678|
Warning tone| ON (default); OFF| ON / OFF prompt tone
Format the memory card| YES; NO (default)| Operate cautiously! Formatting the memory card will delete all filedata. Please make a backup
Serial number| ON; OFF (default)| Numbers and letters can be used to tag this camera to indicate the position of the obtained photos and videos.
Restore Settings| YES; NO (default)| After pressing OK to confirm,all camera settings will be restored to the default values

Positioning of the camera

In the TEST mode, it is beneficial to determine the best possible detection angle and range of the motion sensor. First, open the TEST mode and operate as follows: Please fix the camera on a tree or other suitable object about 1 – 2 m high, and adjust the direction as required;

Move slowly from one side of the observation area to the other side, moving parallel to the camera, and observing the indicator.

If the red indicator lights up, it means you are detected by the motion sensor, according to the detection range, and find the best position for the appropriate camera.

Note: To prevent unnecessary photos, we recommend not pointing the camera straight in the direction of sunlight. Make sure that the camera height is consistent with the area to be observed. Do not set the camera too close to the tree branches to avoid irrelevant triggering.

Working mode

When the switch is set to the ON position, the camera enters the working mode.

The screen will enter the STANDBY mode after a countdown of 15 seconds. Once a moving object is detected to enter the PIR detection range, the sensor will activate the camera to shoot/record.

Connect to the computer

The camera can be connected to the computer through the attached mini USB to view the existing photos/videos.

Technical Specifications

1280720@30fps (default) 720480@30fps 640×480@30fps
Video format| AVI(H.264)
Objektiv| f=4.0mm F/NO=2.0 FOV=90 °
PIR detection angle and distance| The detection angle up to 120 ° and the detection distance is 65 ft
Detection distance| 80 ft (in the day), 65 ft (at night)
Number of infrared fill lamps| 34 infrared lamps, 940 nm (no glow effect)
Trigger time| 0.2s
Dustproof, waterproof grade| IP66
Living broadcast function| APP real-time preview
Connection method| Camera WIFI ON/OFF via Bluetooth
Memory card type| Up to 512 GB SD card, Class 10 or above
Working temperature| -22°F ~ 160°F
Power supply mode| Battery or external power supply
Type of battery| AA Battery
Operating voltage| 6V
External power| DC 6V
Standby time| Up to 6 months

Common Troubleshooting

1. The camera cannot be turned on
   A. Please check whether the battery has been installed properly and whether the electrodes are correct;
   B. Check whether the battery capacity is fully discharged;
   C. If an external power supply is used, please check whether the external power supply is used correctly.

2. Display of an error in SD card
   A. Please format the SD card on the camera when sing the camera for the firsttim;
   B. Please check whether the SD card has been installed in place;
   C. Check whether the SD card above Class 10 is used.

3. Video displayed wrongly on the computer
   A. Make sure to use a correct video player;
   B. Please format the memory card before using it.

4. The picture is not clearly displayed
   A. Be sure to remove the protective film of the lens before use;
   B. Check whether there is dirt in front of the camera lens. If so, please wipe it clean with a dry cloth before use.

5. The camera cannot take pictures or record videos
   A. Check whether the SD card is full. If it is full, please transfer the files in the SD card to other devices before use it again;
   B. Enter the REPLAY mode and delete some unnecessary pictures and videos;
   C. The memory card format is incorrect. Please reformat the memory card or replace it with a new one.

6. The camera cannot be turned off Once this happens, please remove all batteries and restart the camera.

7. The password is forgotten, and the camera cannot be opened
   Firstly, turn the switch to OFF, at the same time, press and hold the REPLAY + VIDEO key, and turn the switch from OFF to TEST.

8. What are the ranges of WiFi and Bluetooth?
   The serviceable range of camera WiFi is about 10 m in the forest or indoors, and about 20 m in open space.

9. At what distance can I turn on WiFi with Bluetooth?
   The maximum service distance of Bluetooth switch of the camera is 20 m.

10. Can it be connected to home WiFi and a network for camera use?
    No, trail camera is connected to your phone’s WiFi, not your home WiFi/network. Please download the “Trail Camera Wifi” APP on your mobile phone, and then connect to Wifi. You can adjust the settings and view photos/videos directly on your phone.

11. The camera didn’t detect anything
    A. Please make sure the camera is not behind the glass;
    B. Please make sure that the protective film of PIR sensor has been torn off;
    C. Please check the settings in the menu and adjust the detection distance and sensitivity of the camera.

12. Is this APP suitable for iPhone?
    Yes, both iOS and Android systems are supported.
    Please download the “Trail Camera Wifi” APP from Apple Store or GooglePlay.

13. Is it possible to connect 9V DC or 12V DC power supply instead of a battery?
    Yes, you can use 9V DC power supply for this camera, and there is an interface dedicated to the external power supply. It is recommended to use 8*1.5V AA battery in this tracking camera to get the maximum battery life.

14. Why the camera doesn’t record at night but works well during the day?
    Please check the battery power of the camera. If the battery power is insufficient (less than 1/3), the night vision function will automatically turn off. Please replace the new battery to restore the night vision function.

15. Why the “Target Recording Time” function does not work?
    Please check if you have also turned on the “time-lapse” function and selected the time-lapse mode, then set the time-lapse length.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>