Regalo 20 Series Swing Down Bed Rail Instructions
- June 14, 2024
- regalo
Table of Contents
Swing Down Bed Rail
Models: 2020, 2220
• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF BED RAIL.
KEEP INSTRUCTIONS FOR FUTURE USE.
www.regalo-baby.com
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA , EE. UU.
866.272.5274 (U.S. only / aux États-Unis seulement / solo en EE. UU.) or / ou
/ o 952.435.1080
Made in China
Before Assembly
PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:
A. Mesh Wall
B. Upper Support Bar
C. Upper Support Bar
D Bottom Support Bar A
E. Bottom Support Bar B
F. Hinge Assembly A
G. Hinge Assembly B
BEFORE USING PRODUCT
Read and follow all instructions carefully to ensure that your product is
properly installed.
Failure to follow these instructions for the assembly of use of your bed rail
could result in serious injury or death. The safety of your child is your
responsibility. Please keep these instructions for your reference.
IMPORTANT
- Do not use two separate bed rails on one bed. The bed rails will not function properly and could be a safety hazard. Should you need coverage on both sides of the bed, purchase the Regalo Double Sided Bed Rail.
CARE AND MAINTENANCE
Periodically check the bed rail for signs of damage, wear or for missing
components. Do not use if any part is missing, worn or damaged. Check the bed
rail regularly to make sure all hardware and mountings are tight and secure.
Do not use abrasive cleaners or bleach when cleaning. Proper cleaning of bed
rail can be done by sponging it with warm water and mild detergent. Do not
machine wash.
Assembling Your Bed Rail
Insert the upper support bar (C) into the bottom support bar (E). Make sure the spring pin fits securely into the opposing hole so that the two pieces cannot pull apart. Repeat on the opposite side (B, D) of the bed rail.
With the upper and bottom support bars assembled, connect the two sides.
NOTE: Make sure that the spring pins are secured into the opposing holes
so that the bed rail cannot pull apart.
To install the mesh wall (A) on the bed rail, slide it over the frame until it reaches the other end, zip it shut, then attach the velcro strap over the zipper to complete the installation. Mesh wall must go over entire bed rail frame.
With the wall of the bed rail completely assembled, you will now connect the hinge assemblies (F, G).
Insert one side of the wall frame with locating pin into the hinge assembly
labeled “B”. Press in the metal spring button to fully insert the tube into
the hole in the plastic hinge. The spring button should line up with the
access hole in the plastic sleeve on the hinge. The spring button will rebound
and lock the tube in place. Repeat on opposite hinge assembly “A”.
NOTE: If the zipper does not close securely, make the necessary
adjustments to ensure proper closure. DO NOT use the bed rail without securely
zipping the mesh wall properly.
Installing Your Bed Rail
Start by placing the bed rail on the side of the bed you have chosen for installation. The left and right swing lock and strap assemblies should be placed on top of the box spring that will support the mattress. The ‘T’ shaped anchors and straps should be extended opposite the bed rail and mounted to the outer edge of the box spring or mattress support structure.
Once the bed rail is properly placed, check to make sure the left and right
swing lock and strap assemblies are parallel to one another. Then, place the
mattress on top of the assembly.
NOTE: In order for the bed rail mesh wall to be firmly held against the
side of the mattress you MUST properly tighten the anchoring straps. Please
follow the next STEPS 3 – 4 carefully.
NOTE: You may need to release the strap locking buckles located on the
under side of the plastic hinges. Ensure that the large end of the anchor is
pointing up. The anchoring straps should not be twisted. If twisted, the
anchoring straps will not tighten properly.
Tighten the straps to bring the bed rail into its proper position. To tighten the straps, first release the strap locks on the under side of the left and right under bars. Pull the straps towards you until all the excess slack has been pulled out from under the mattress.
If the strap does not pull through smoothly, the strap may be twisted under
the mattress. Correct this before continuing with the installation. Once you
have taken the slack out of the straps, give one final pull on the strap end,
hold it, and push down on the locking buckle to secure the strap tension. Use
the same procedure for each side to properly secure the bed rail.
NOTE: When using this bed rail on a foam mattress with little or no
internal structure, make sure not to over tighten the mounting straps. If
over-tightened, the mattress will likely fold or buckle in the middle and this
will cause the bed rail to not provide your child with the highest level of
safety. Make slight adjustments to find the best level of tightness on your
mattress. The bed rail must be tight but should not buckle or fold.
With your bed rail in the ‘up’ position push down on the locking tabs to
secure your bed rail in place.
NOTE: After locking both buckles, check to make sure that the mesh wall
of the bed rail is firmly up against the side of the mattress. There should be
NO GAPS. If the mesh wall is not firmly against the side of the mattress, check
to make sure the locking buckle is unctioning properly and that the strap is
not twisted beneath the mattress. Once this has been checked and corrected if
needed, unlock the buckle, pull on the end of the strap tightly and lock the
buckle again. Store the excess anchoring strap material by tucking it under
the mattress. Do not cut excess strap, may cause strap to fray.
Operating the Swing Down Feature
With the bed rail side in the ‘up’ position, release the locking tabs on each
swing lock and arm assembly by pushing them up. This will allow the upper part
of the bed rail to move freely.
NOTE: Be sure to continue to hold the upper part of the bed rail so that
it does not drop down on its own.
With both locking tabs turned to the ‘open’ position, hold the upper part of
the bed rail firmly and swing it down. The bed rail should now be in the ‘down’
position. To return the bed rail to the ‘up’ position, reverse STEPS 1 – 2.
NOTE: Make sure that the bed rail is in the ‘up’ position and the locking
tabs are securely closed before leaving a child alone in the bed.
Replacement Parts
A. MODEL 2020
Swing Down Bed Rail
SD – Mesh Wall
White = #23069
MODEL 2220
Extra Long Swing Down Bed Rail
XLSD – Mesh Wall
White = #23076
90 DAYS LIMITED WARRANTY
If, during the first 90 days after consumer purchase of the item, under
reasonable and non-commercial use and conditions of maintenance, it fails
while owned by the original purchaser because of the quality of materials or
workmanship of finish and assembly, Regalo International, LLC, will replace or
repair it at Regalo’s option. PROOF OF PURCHASE REQUIRED.
WARNING
- SUFFOCATION AND STRANGULATION HAZARD.
- Gaps in and around bed rails have entrapped young children and killed infants.
- NEVER use with children younger than 2 years old. USE ONLY with older children who can get in and out of adult bed without help.
- NEVER use in place of crib.
- NEVER use unless bed rail is tight against mattress, without gaps, and at least 9 in. from headboard and footboard. Do not fill gaps with pillows, blankets, or other items that can suffocate children.
- NEVER use on toddler bed, bunk bed, water bed, or bed with inflatable mattress. Use ONLY on adult bed.
- Use ONLY on a bed ranging from twin size to queen size.
- Use ONLY on adult bed with box spring and mattress.
- This bed rail is NOT recommended to be used on a platform or similar style bed.
- This bed rail is intended for use with children 2 years to 5 years of age.
- Discontinue use if damaged, broken, or if parts are missing.
- Do not use if bed rail is not fully assembled.
- Periodically check that all spring pins are fully engaged on bed rail support bars.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>