Dripex D-THO-4824BC Electric Sit Stand Desk Instruction Manual

June 14, 2024
Dripex

D-THO-4824BC Electric Sit Stand Desk

Electric Sit-Stand Desk

Product Information:

Component Quantity
Beam 1
Left Leg 1
Right Leg 1
Drive Rod 1
Side Plate 2
Leg Base 2
Board 2
Desk Connection Hook 2
Hand Controller 1
Power Supply 1
Drawer 1
Desk Connection Plate 3
Cable Hole Cover 2
Wooden Pin 4
Cable Clip 2
Silicone Sheet 10
Screws (M-A) 1
Screws (M-B) 10
Wrench (M-F) 1
Wrench (M-G) 1
Screws (M-C) 8
Screws (M-D) 12
Screws (M-E) 12

Product Usage Instructions:

  1. Align the holes of Left Leg (2) and Drive Rod (4), using Wrench
    (M-F) to secure both with Screw (M-A).

  2. Insert Drive Rod (4) into the hole of Right Leg (3). If it
    cannot be inserted, tilt Right Leg (3) slightly until they are
    matched.

  3. As shown, use Wrench (M-G) to install Beam (1) to the Legs (2
    & 3) with Screws (M-B)*6.

  4. Using Wrench (M-G), install Leg Base (6)*2 to the Legs (2 &

  1. respectively with Screws (M-C)*8.
  1. Using Wrench (M-G), install Side Plate (5)2 on each side of
    the Legs (2 & 3) with Screws (M-B)
    4.

  2. Fix Silicone Sheet (16)*2 to the corresponding position on the
    Beam (1).

  3. Fix Boards (7a & 7b) with Wooden Pin (14)4. Use
    screwdriver, with Screws (M-D)
    10, install Desk Connection Plate
    (12)3 to the middle of the Boards, and Desk Connection Hook (8)2
    to both sides of the Boards.

  4. Fix Silicone Sheet (16)*8 to the corresponding hole position on
    the Boards (7a & 7b).

  5. Use screwdriver, secure the Leg part to the Boards (7a &
    7b) with Screws (M-E)8. Please align the Silicone Sheet
    (16)
    8.

  6. As shown, connect the motor at the Left Leg (2), Hand
    Controller (9), and Power Supply (10) in turn.

  7. Using screwdriver, install Hand Controller (9) to the Board
    (7a) with Screws (M-D)2. Secure the connecting cable with Cable
    Clip (15)
    2 and glue it to the bottom of the Board.

  8. Prepare the Drawer (11). Using screwdriver, install it to the
    Board (7a) with Screws (M-E)*4.

  9. Insert Cable Hole Cover (13)*2 into the hole in the Board
    (7b).

Using the Controller:

  • Raise the Desk: Press the “v” button to raise the desk
    continuously until it reaches the highest position or the button is
    released.

  • Lower the Desk: Press the “v” button to lower the desk
    continuously until it reaches the lowest position or the button is
    released.

  • Select Height Setting 1: Press the “1” button, and the desk
    will move to the height that was previously set for that
    button.

  • Select Height Setting 2: Press the “2” button, and the desk
    will move to the height that was previously set for that
    button.

  • Select Height Setting 3: Press the “3” button, and the desk
    will move to the height that was previously set for that
    button.

  • Save Current Height Setting: Short-press the “S” button, and
    the screen will show ‘S-‘. Press the “1”, “2”, or “3” button to
    save the current height setting to that button. When you press the
    “1”, “2”, or “3” button, the desk will move to the height that was
    previously set for that button. Any button press will stop the
    desk.

ELECTRIC SIT-STAND DESK
Instruction Manual
D-THO-4824BC

1 x1
Beam

2 x1
Left Leg

3 x1
Right Leg

4 x1
Drive Rod

5 x2
Side Plate

6 x2
Leg Base

7a x1
Board

7b x1
Board

8 x2
Desk Connection Hook

9 x1
Hand Controller

10 x1
Power Supply

11 x1
Drawer

12 x3
Desk Connection Plate

13 x2
Cable Hole Cover

14 x4
Wooden Pin

15 x2
Cable Clip

16 x10
Silicone Sheet

M-A x1
Screws

M-B x10
Screws

2.5mm
M-F x1
Wrench

5mm
M-G x1
Wrench

M-C x8
Screws

M-D x12
Screws

M-E x12
Screws

Screwdriver is required during the installation please prepare it in advance.

Step 1
4

M-F
M-A 2

Align the holes of Left Leg (2) and Drive Rod (4), using Wrench (M-F) to secure both with Screw (M-A).

Step 2
4 3
Insert Drive Rod (4) into the hole of Right Leg (3). If it cannot be inserted tilt Right Leg (3) slightly until they’re matched.
Step 3
2
M-G M-B
1 3
As shown, use Wrench (M-G), install Beam (1) to the Legs (2&3) with Screws (M-B)*6.

Step 4

M-G
M-C
6

Using Wrench (M-G), install Leg Base (6)2 to the Legs (2&3) respectively with Screws (M-C)8.
Step 5
5
M-B
M-G
Using Wrench (M-G), install Side Plate (5)2 on each side of the Legs (2&3) with Screws (M-B)4.

Step 6
16 1

Fix Silicone Sheet (16)*2 to the corresponding position on the Beam (1).

Step 7

7b
14

7a

M-D 8
M-D 12
Fix Boards (7a&7b) with Wooden Pin (14)4. Use screwdriver, with Screws (M-D)10, install Desk Connection Plate (12)3 to the middle of the Boards , and Desk Connection Hook (8)2 to both sides of the Boards.
Step 8
16
Fix Silicone Sheet (16)*8 to the corresponding hole position on the Boards (7a&7b).

Step 9
M-E 16

Use screwdriver, secure the Leg part to the Boards (7a&7b) with Screws (M-E)8. Please align the Silicone Sheet (16)8.

Step 10

9
2

9
10

As shown, connect the motor at the Left Leg (2), Hand Controller (9) and Power Supply (10) in turn.

Step 11
1

M-D 9

15
2 3

Using screwdriver, install Hand Controller (9) to the Board (7a) with Screws (M-D)2. Secure the connecting cable with Cable Clip (15)2 and glue it to the bottom of the Board.
Step 12
11 M-E

Prepare the Drawer (11). Using screwdriver, install it to the Board (7a) with Screws (M-E)*4.

Step 13
13
Insert Cable Hole Cover (13)*2 into the hole in the Board (7b).

Using the Controller
Raise the Desk
Press the v button to raise the desk continuously until it reaches the highest position or the button is released.
Lower the Desk
Press the v button to lower the desk continuously until it reaches the lowest position or the button is released.
Select Height Setting 1
Press the 1 button, and the desk will move to the height that was previously set for that button.
Select Height Setting 2
Press the 2 button, and the desk will move to the height that was previously set for that button.
Select Height Setting 3
Press the 3 button, and the desk will move to the height that was previously set for that button.
Save Current Height Setting
Short-press the S button, and the screen will show `S-‘ .Press the 1 , 2 , or 3 button to save the current height setting to that button. When you press
the 1 , 2 , or 3 button, the desk will move to the height that was previously set for that button. Any button-press will stop the desk.

Settings
Reset
Press and hold the v button until ‘rst’ is displayed. Continue holding until the desk goes down to its lowest level and comes back up slightly. Release the button, and reset is complete. If the button is released during the reset procedure, reset will stop. The desk won’t work until reset is done correctly.
Child Lock
Press and hold the v and v buttons together for 5 seconds to turn child lock on. The screen will show ‘LOC’ and the buttons will be disabled. Turn child lock off the same way.
Settings Menu
Press and hold the S button for 5 seconds to enter the settings menu. Short- press the S button to navigate through the menu. Short-press the v or v button to adjust the settings. Long-press the v or v button to quickly adjust the height settings. Press and hold the S button again to save the changes. ‘SUS’ will be displayed if saving is successful (or ‘FAL’ if saving fails). If there is no button-press for 10 seconds, the settings menu will be exited automatically.
Power-Saving Mode
The screen will turn off if there is no button-press for a minute. Any button- press will turn the screen on again.

SC0 SC1 SC4 hot r-6 rst

Protection Mode Error Codes
Standby Overvoltage Protection: Standby voltage too high. Power off the desk, check the connection between power and the controller, and power on again. If error code persists, please contact technical support.
Power Supply Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again. If error code persists, please contact technical support.
Operating Overvoltage Protection: Operating voltage too high. Power off the desk, check the connection between power and the controller, and power on again. If error code persists, please contact technical support.
Overheating Protection: When the motor has been working continuously for too long, it will stop operating to prevent overheating. Wait for at least 18 minutes (until error code disappears) before making any further height adjustment.
Power Supply Overvoltage Protection (during use): Input voltage too high. Error clears when power supply voltage returns to normal. If error code persists, please contact technical support.
Reset Warning: Continue to complete reset.

E10

Short Circuit Protection: Power off, check the cable connections, and power back on again. If error persists, please contact technical support.

E11

Overloading Protection: Max load exceeded. Error code will persist for 20 seconds (DO NOT operate). Take the things off the desk and confirm there is no mechanical damage before trying again.

E12

Motor Phase Error Protection: Power off, check the cable connection between the motor and the controller, and power back on again. Then follow the reset instructions. If error code persists, please contact technical support.

E13 E14

Sensor Malfunction Warning: Motor sensor can’t be detected. Power off, check the cable connection between the motor and the controller, and power back on again. Then follow the reset instructions. If error code persists, please contact technical support.
Anti-Collision System Warning: Impact detected. The desk will move 2″ (50mm) in the opposite direction and stop.

E16

Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected. If error code persists, please contact technical support.

E17

Mechanical Failure Warning: Check if there is any structural damage or motor fault.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals