Lenovo 14IRP8 Yoga 9 Pro Laptop User Guide

Lenovo 14IRP8 Yoga 9 Pro Laptop

Product Information

Specifications

• Machine Type (MT): 83BU
• Processor: Intel Core i7
• Memory: 8GB LPDDR4X RAM
• Storage: 512GB PCIe SSD
• Display: 14″ FHD IPS Touchscreen
• Operating System: Windows 10

Safety Information

This chapter provides important safety information that you need to be familiar with before servicing your Lenovo Yoga Pro 9i.

General Safety

1. Ensure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your  feet.
3. Use a slow lifting force and avoid sudden movements or  twisting.
4. Lift by standing or pushing up with your leg muscles to avoid  strain on your back.
5. Do not attempt to lift any object weighing more than 16 kg (35  lb) or that you consider too heavy for you.
6. Avoid covering the air vents or obstructing them with labels or  stickers.

About this manual

This manual contains service and reference information for the following Lenovo products.

Machine / Machine type (MT)

• Yoga Pro 9 14IRP8: 83BU
• Yoga Pro 9 14IRP8 D1: 83BU

Important

• This manual is intended only for trained service technicians who are familiar with Lenovo products.
• Before servicing a Lenovo product, be sure to read all the information under Chapter 1 “Safety information”.

Safety information

This chapter presents the following safety information that you need to be familiar with before you service a Lenovo notebook computer.

General safety

Follow these rules to ensure general safety:

• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
  1. Make sure that you can stand safely without slipping.
  2. Distribute the weight of the object equally between your feet.
  3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
  4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, make sure that other service technicians and the customer’s personnel are not in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the machine.
• Keep your tool case away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a non-conductive clip, about 8 centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.
• Attention: Metal objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan louvers or cover them with labels or stickers.

Electrical safety

Observe the following rules when working on electrical equipment.

Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.

• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
  • Performing a mechanical inspection
  • Working near power supplies
  • Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
  • Ensure that another person, familiar with the power-off controls, is near you.
  • Attention: Another person must be there to switch off the power, if necessary.
  • Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back.
  • Attention: An electrical shock can occur only when there is a complete circuit. By observing the above rule, you may prevent a current from passing through your body.
  • When using testers, set the controls correctly and use the approved probe leads and accessories for that tester.
  • Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames.Observe the special safety precautions when you work with very high voltages; Instructions for these precautions are in the safety sections of maintenance information. Use extreme care when measuring high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, non-grounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on when they are removed from their normal operating places in a machine:
  • Power supply units
  • Pumps
  • Blowers and fans
  • Motor generators
  • Similar units as listed above
• This practice ensures correct grounding of the units.
• If an electrical accident occurs:
  • Use caution; do not become a victim yourself.
  • Switch off power.
  • Send another person to get medical aid.

Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-Lenovo features or options not covered by this inspection guide. If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.

Consider these conditions and the safety hazards they present:

• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock)
• Explosive hazards, such as a damaged cathode ray tube (CRT) face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware

To determine whether there are any potentially unsafe conditions, use the following checklist at the beginning of every service task. Begin the checks with the power off, and the power cord disconnected.

Checklist:

1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for:
   • A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and the frame ground.
   • The power cord should be the authorized type specified for your computer. Go to: http://www.lenovo.com/serviceparts-lookup
   • Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.

Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.

Notes

1. Use product-specific ESD procedures when they exceed the requirements noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.

When handling ESD-sensitive parts:

• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement.

Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.

• Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
• When working on a double-insulated or battery-operated system, use an ESD common ground or reference point. You can use coax or connector-outside shells on these systems.
• Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements

• Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.

Safety notices (multilingual translations)

The safety notices in this section are provided in the following languages:

• English
• Arabic
• Brazilian Portuguese
• French
• German
• Hebrew
• Japanese
• Korean
• Spanish
• Traditional Chinese

DANGER

• Before the computer is powered on after FRU replacement, make sure that all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.
• Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery.
• The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the  battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result  in ignition or explosion of the battery.
• The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery.
• If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing.
• To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card.
• Though the main batteries have low voltage, a short-circuited or grounded battery can produce enough current to burn personnel or combustible materials.
• Unless hot swap is allowed for the FRU being replaced, do as follows before removing it: power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and disconnect any interconnecting cables.

General checkout

This chapter contains the following topics:

• Before you go to the checkout instructions, ensure that you read the following important notes.

Important notes

• Only certified trained personnel should service the computer.
• Before replacing any FRU, read the entire page on removing and replacing FRUs.
• Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs might be overwritten.
• Replace an FRU only with another FRU of the correct model. When you replace an FRU, make sure that the model of the machine and the FRU part number are correct by referring to the FRU parts list.
• An FRU should not be replaced because of a single, unreproducible failure. Single failures can occur for a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. Consider replacing an FRU only when a problem recurs. If you suspect that an FRU is defective, clear the error log and run the test again. If the error does not recur, do not replace the FRU.
• Be careful not to replace a nondefective FRU.

What to do first

When you return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it:

1. Name and phone number of service technician
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Failure symptoms, error codes appearing on the display, and beep symptoms
6. Procedure index and page number in which the failing FRU was detected
7. Failing FRU name and part number
8. Machine type, model number, and serial number
9. Customer’s name and address

Note: During the warranty period, the customer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer. Following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use.

Before checking problems with the computer, determine whether the damage is covered under the warranty by referring to the following list:

The following are not covered under warranty:

• LCD panel cracked from the application of excessive force or from being dropped
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force
• Damage caused by liquid spilled into the system
• Damage caused by the improper insertion of a personal-computer card (PC card) or the installation of an incompatible card
• Improper disc insertion or use of an external optical drive
• Fuses blown by attachment of a non-supported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect ac power adapter on laptop products

The following symptoms might indicate damage caused by non-warranted activities:

• Missing parts might be a symptom of unauthorized service or modification.
• Check for obvious damage to a hard disk drive. If the spindle of a hard disk drive becomes noisy, the hard disk drive might have been dropped or subject to excessive force.

CRU list

Table 1. Models: Yoga Pro 9 14IRP8 and Yoga Pro 9 14IRP8 D1 (MT: 83BU)

Identifying FRUs

Identifying FRUs (CRUs)

Locate FRUs and CRUs

• The exploded illustrations help Lenovo service technicians identify FRUs or CRUs that they may need to replace when servicing a customer’s computer.

Table 2. FRU (CRU) categories

Note: The LCD unit as a whole is not an FRU. It contains FRUs as its components.

2| Upper case
3| System board
4| I/O board
5| I/O board bracket
6| I/O board cable
7| Heat sink
8| Fan
9| Solid-state drive (SSD)
 10| Solid-state drive (SSD) mylar
 11| Speakers
 12| Battery pack
 13| Lower case
 14| Wi-Fi card
 15| Touchpad board cable
a| Power cord
b| ac power adapter
c| Screw kit

Table 3. FRU (CRU) categories

Removing a FRU or CRU

Service tools

The following table lists tools for servicing Lenovo computers. Tools with a cross mark are needed for serving the product models as described by this publication. Prepare them before you service the product.

Table 4. Service tools

Notes

• T30 screw drivers are used to service the new Intel Xeon CPUs.
• Hexagonal sockets are used to remove antenna connectors.
• Silicone grease is applied to the CPU and heatsink surfaces to eliminate air gaps.

General guidelines

When removing or replacing an FRU, ensure that you observe the following general guidelines:

1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts.
2. Begin by removing any FRUs that have to be removed before replacing the failing FRU. Any such FRUs are listed at the beginning of each FRU replacement procedure. Remove them in the order in which they are listed.
3. Follow the correct sequence in the steps for removing an FRU, as shown in the illustrations by the numbers in square callouts.
4. When removing an FRU, move it in the direction as shown by the arrow in the illustration.
5. To install a new FRU in place, perform the removal procedure in reverse and follow any notes that pertain to replacement.
6. When replacing an FRU, carefully retain and reuse all screws.
7. When replacing the base cover, reapply all labels that come with the replacement base cover. If some original labels are not included with the replacement base cover, peal them off from the original base cover and paste them on the replacement base cover.

DANGER

• Before removing any FRU or CRU, shut down the computer and unplug all power cords from electrical outlets.

Attention

• After replacing an FRU, do not turn on the computer until you have ensured that all screws, springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.
• The system board is sensitive to and can be damaged by ESD. Before touching it, establish personal grounding by touching a ground point with one hand or by using an ESD strap (P/N 6405959).

Remove the lower case

Make sure the computer has been shut down before servicing the computer.

• Step 1. Place the computer upside down on a flat surface.
• Step 2. Remove five screws.

• Step 3. Pry up the latches and then remove the lower case.

• Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Lower case

Remove the battery pack

Make sure the following FRU (or CRU) has been removed.
“Remove the lower case” on page 28

• Step 1. Disconnect the battery pack cable from the system board.
  • Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.
• Step 2. Remove three screws and then remove the battery pack.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Battery pack

Remove the solid-state drive (SSD)

Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case

• Step 1. Disconnect the battery pack cable from the system board.
  • Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.
• Step 2. Remove one screw and then remove the SSD by pulling it away from the slot.

• Step 3. Remove the SSD mylar.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following replacement parts:

• Solid-state drive (SSD)
• Solid-state drive (SSD) mylar

Remove the Wi-Fi card

Make sure the following FRU (or CRU) has been removed.
“Remove the lower case”

• Step 1. Disconnect the battery pack cable from the system board.
  • Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.
• Step 2. Detach the main and auxiliary antenna cable connectors. Remove one screw and then remove the Wi-Fi card by pulling it away from the slot.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Wi-Fi card

Remove the touchpad board cable

Make sure the following FRUs (CRUs) have been removed.

“Remove the lower case”
“Remove the battery pack”

• Step 1. Peel off the keyboard cable.
• Step 2. Peel back the tape on the touchpad board connector. Disconnect the touchpad board cable from the system board and touchpad board. Remove the touchpad board cable. Figure 10.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Touchpad board cable

Remove the I/O board bracket

Make sure the following FRU (or CRU) have been removed.
“Remove the lower case”

• Step 1. Disconnect the battery pack cable from the system board.
  • Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.
• Step 2. Remove two screws then peel off the tape. Remove the I/O board bracket.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: I/O board bracket

Remove the I/O board

Make sure the following FRU (or CRU) have been removed.

“Remove the lower case”
“Remove the I/O board bracket”

• Step 1. Disconnect the battery pack cable from the system board.
  • Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.
• Step 2. Disconnect the speaker cable connector and I/O board cable connector from the I/O board.
• Step 3. Remove one screw then remove the I/O board.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: I/O board

Remove the heat sink

Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case”

• Step 1. Disconnect the battery pack cable from the system board.
  • Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.
• Step 2. Peel off conductive fabric on the heat sink.
• Step 3. Loosen five screws and then remove the heat sink.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Heat sink

Remove the fan

Make sure the following FRUs (or CRUs) have been removed.
“Remove the lower case” on page 28“Remove the heat sink”

• Step 1. Disconnect the battery pack cable from the system board.
  • Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.
• Step 2. Disconnect the fan cable from the system board. Release the cables from the cable guide.
• Step 3. Remove six screws then remove the fan.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Fan

Remove the system board and the I/O board cable

Make sure the following FRUs (or CRUs) have been removed.

“Remove the lower case”
“Remove the battery pack”
“Remove the solid-state drive (SSD)”
“Remove the Wi-Fi card”
“Remove the heat sink”
“Remove the fan”

• Step 1. Peel off the tape.
• Step 2. Disconnect cables connected to the system board.
• Step 3. Remove six screws and then remove the system board.

• Step 4. Peel off the tape then disconnect the I/O board cable from the system board.

Go to https://support.lenovo.com/partslookupto look up the Lenovo part numbers of the following replacement parts:

• System board
• I/O board cable

Use a Golden Key U1 tool to flash-write key id information

After replacing the system board and re-assembling the computer, use a pre- made Golden Key U1 tool to start the computer and flash-write the serial number (SN), machine type (MT), product name (PN), and UUID to the new system board. The Golden Key U1 tool is prepared by running the U1 Update software on a FAT32-formatted USB thumb drive. Go to http://support.lenovo.com/us/en/solutions/HT506954 for detailed instructions on how to create and use a Golden Key U1 tool.

Remove the speakers

Make sure the following FRUs (CRUs) have been removed.

“Remove the lower case”
“Remove the battery pack”
“Remove the solid-state drive (SSD)”
“Remove the Wi-Fi card”
“Remove the I/O board bracket”
“Remove the I/O board”
“Remove the heat sink”
“Remove the fan”
“Remove the I/O board”
“Remove the system board and the I/O board cable”

• Step 1. Remove six screws then release the cables from the cable guide. Remove the speakers.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Speakers

Remove the LCD module

Make sure the following FRUs (CRUs) have been removed.
“Remove the lower case”

• Step 1. Disconnect the battery pack cable from the system board.
  • Attention: Use your fingernails to pull the connector to unplug it. Do not pull the cable.
• Step 2. Peel off the two pieces of tape.
• Step 3. Disconnect the EDP cable and camera cable from the system board then detach the main and auxiliary antenna cable connectors. Release the cables from the cable guide.
• Step 4. Rotate the LCD module to an angle of more than 90 degrees and place the computer on a flat surface as shown. Remove four screws and then remove the LCD module.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: LCD module

Remove the upper case

Make sure the following FRUs (CRUs) have been removed.

• “Remove the lower case”
• “Remove the battery pack”
• “Remove the solid-state drive (SSD)”
• “Remove the Wi-Fi card”
• “Remove the touchpad board cable”
• “Remove the I/O board bracket”
• “Remove the I/O board”
• “Remove the heat sink”
• “Remove the fan”
• “Remove the I/O board”
• “Remove the heat sink”
• “Remove the fan”
• “Remove the system board and the I/O board cable”
• “Remove the speakers”
• “Remove the LCD module”

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Upper case

Disassemble the LCD module

The LCD module as a whole is not an FRU. Instead, it contains FRUs as its components. Before disassembling the LCD module, make sure it has been detached from the upper case.

Remove the hinge cover

Make sure the following unit has been removed.
“Remove the LCD module”

• Step 1. Remove the hinge cover.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Hinge cover

Remove the strip cover

Make sure the following FRUs (CRUs) have been removed.

“Remove the LCD module”
“Remove the hinge cover”

• Step 1. Release the cable from the cable guide.
• Step 2. Remove six screws and then remove the strip cover.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Strip cover

Remove the LCD panel and EDP cable

Make sure the following FRUs (CRUs) have been removed.
“Remove the LCD module”
“Remove the hinge cover”
“Remove the strip cover”

• Step 1. Remove the two pieces of removable tape with tweezers and then remove the LCD panel.
  • Note: The removable tape is not reusable. Replace it when replacing related FRUs.
• Step 2. Peel off the tape and then detach the touch board connector.
• Step 3. Turn over the LCD panel and peel off the EDP connector absorber and then detach the EDP cable from the LCD panel.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following replacement parts:

• LCD panel
• Removable tape
• EDP connector absorber
• EDP cable

Remove the microphone rubbers

Make sure the following FRUs (CRUs) have been removed.

“Remove the LCD module”
“Remove the hinge cover”
“Remove the strip cover”
“Remove the LCD panel and EDP cable”

• Step 1. Remove the microphone rubbers.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following replacement parts:

• Microphone rubbers
• Removable tape

Remove the camera

Make sure the following FRUs (CRUs) have been removed.

“Remove the LCD module”
“Remove the hinge cover”
“Remove the strip cover”
“Remove the LCD panel and EDP cable”

• Step 1. Remove the camera rubber.
• Step 2. Disconnect the camera cable from the camera board and then remove the camera.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following replacement parts:

• Camera
• Removable tape

Remove the camera cable

Make sure the following FRUs (CRUs) have been removed.

“Remove the LCD module”
“Remove the hinge cover”
“Remove the strip cover”
“Remove the LCD panel and EDP cable”

• Step 1. Remove the camera rubber.
• Step 2. Disconnect the camera cable from the camera board and then remove the camera cable.

Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following replacement parts:

• Camera cable
• Removable tape

Remove the LCD cover

Make sure the following FRUs (CRUs) have been removed.

“Remove the LCD module”
“Remove the hinge cover”
“Remove the strip cover”
“Remove the LCD panel and EDP cable”
“Remove the camera”
“Remove the camera cable”

Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: LCD cover

Appendix A

Appendix A.Label locations

• Labels attached to the base cover are country/region specific.
• Make sure to apply the appropriate labels to the replacement base cover.

Table 5. All base cover labels

Label| Label name| Applied country/region| Label dimensions
---|---|---|---
a| Country label| Malaysia label| 8 mm x 8 mm
 b| TW vision warning label| 70 mm x 10 mm
c| Vietnam energy label| 35 mm x 16 mm
 d| KCC Printing label| 50 mm x 22 mm
e| WL/BT label| South Africa| 20 mm x 10 mm
The United Arab Emirates| 45 mm x 20 mm
 f| CO2 label| Not defined| 18 mm x 18 mm
g| OS label| 16.077 mm x 22.501 mm

Trademarks

• LENOVO and the LENOVO logo are trademarks of Lenovo.
• All other trademarks are the property of their respective owners. © 2023 Lenovo.

References

• support.lenovo.com/us/en/solutions/HT506954
• Lenovo Computer Parts | Genuine Replacement Parts | Lenovo Support US
• Lenovo Computer Parts | Genuine Replacement Parts | Lenovo Support US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>