DRiPEX Q202A-D202 Ergonomic Office Chair Installation Guide

June 14, 2024
Dripex

DRiPEX Q202A-D202 Ergonomic Office Chair

DRiPEX Q202A-D202 Ergonomic Office Chair

PARTS

  1. Base joint

  2. Base legs (x 5 pcs)

  3. SGS cylinder

  4. Base joint Cap

  5. Castors (x 5 pcs)

  6. Tilt/height control

  7. Seat

  8. Arms

  9. Backrest

  10. Headrest

  11. Base Screws (x 10 pcs) M6*12MM

  12. Screws M6*40MM (x 6 pcs)

  13. Washers M6*15MM ( x 6 pcs )

  14. Screws M6*55MM ( x 4 pcs )

  15. Washers (x 7 pcs) M8*17MM

  16. Screws (x 3 pcs) M8*20MM

  17. Washers ( x 3 pcs) M8*13MM

  18. Screws M6*20MM (x 2 pcs)

  19. Screwdriver

ASSEMBLY INSTRUCTIONS

Step 1
Insert base legs into base joint, screw together
Installation Instructions

Step 2
Keep the gap on the castor loop down
Installation Instructions

Step 3
Insert a little, make sure the castor precisely aligned with base leg hole
Installation Instructions

Step 4
Push castor into base leg hole with both of your thumbs
Installation Instructions

  • If jammed, pull out the castor, switch to other castors then push it into holes again.

Follow the installation video on Amazon

Step 5
Insert base caps and cylinder into base
Installation Instructions

Step 6
Arms to seat
Installation Instructions

Step 7
Tilt control to seat
Installation Instructions

14

| | screws M6X55MM*4pcs
---|---|---

15

| | washer M8X17MM*4pcs

Step 8
Backrest to seat
Installation Instructions

16

| | screws M8X20MM*3pcs
---|---|---

15

| | washer M8X17MM*3pcs

17

| | washer M8X13MM*3pcs

Step 9
Insert headrest into the connector (on the top of backrest), then raise headrest to its highest point; Screw the connector. Adjust headrest height
Installation Instructions

Step 10
Installation Instructions

TILT/HEIGHT CONTROL

To Lower the Seat

  1. Keep seated on the chair
  2. Pull out the lever to unlock
  3. Lift up the lever handle
  4. Push in lever to lock
    Tilt/height Control

To Raise the Seat

  1. Pull out the lever to unlock
    Tilt/height Control

  2. Buttocks off the seat, then lift up the lever handle
    2
    Tilt/height Control

  3. Push in lever to lock, sit down
    Tilt/height Control

To Recline

  1. Lay your back on the chair back.
    Pull out the lever to unlock

  2. Press chair back with your back to tilt to 107° or 130°

  3. Push in lever to lock
    Tilt/height Control

If sticks, press chair back with your back a little, then repeat the above steps

Recline backward

  1. Your back off the chair back.
    Tilt/height Control
    Then, pull out the lever to unlock

  2. Press chair back to 130° with your back.
    Tilt/height Control

  3. Your back off the chair back again (chair back will automatically back to 95°)
    3
    Tilt/height Control

  4. Push in lever to lock

If sticks, press chair back with your back a little, then repeat the above steps

CARE AND CLEANING

|

  1. Do NOT get it close to the fire or a wet, acidic and corrosive environment. Avoid overexposure to the sun.
  2. Do NOT use sharp or hooked objects to scrape the chair’
  3. Do NOT use abrasive chemicals for cleaning.
  4. If the frame stained, wipe clean with warm water or pledge surface cleaner (available on Amazon).
  5. If squeaks, tighten screws underneath the seat.

---|---

NOTES AND WARNINGS

|

  1. For one person to sit on. Do NOT stand on.
  2. Do NOT sit on the armrest in case of danger.
  3. Do NOT put overweight on the chair, or used as trolley.
  4. Do NOT let the child sit on the chair alone if he is under 5 year-old.
  5. To avoid danger of suffocation, keep the plastic bag away from babies & children.
  6. If parts missing, broken, damages or wrong. Stop using this product until repairs are made using factory authorized parts.

| For parts missing or any quality issues, please message us via Amazon or email with your order id + photo/video proof. We’ll respond within 24 hours.

CUSTOMERS SUPPORT

support@dripex.co.uk

Logo

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals