Zooz

Zooz Z-Wave Plus Smart Chime

SKU: ZSE33

Quickstart

This is a ****

Siren
for
U.S. / Canada / Mexico.

Please make sure the internal battery is fully charged.

To add this device to your network execute the following action:
Auto Inclusion:1. Put your Z-Wave controller in inclusion mode2. Carefully remove the cover from the device3. Remove the plastic pull-tab from the battery slotthe Chime will automatically enter inclusion mode for 20 seconds4. A new alarm siren / doorbell device will appear on your controller’s device listManual Inclusion:1. Bring the Smart Chime within direct range of your controller2. Carefully remove the cover from the device3. Remove the plastic pull-tab from the battery slot. The LED indicator will blink slowly4. Put your Z-Wave controller in inclusion mode5. Press and release the Z-Wave button on the Smart Chime 3 TIMES quickly. The LED indicator will flash quickly6. A new alarm siren / doorbell device will appear on your controller’s device list (if it connects as an on/off switch, you may need to change the device type manually. Contact us for instructions).

Please refer to the
Manufacturers Manual for more information.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

Product features:- Audio and visual notifications triggered by other Z-Wave devices or scheduled in your routine- Choose from 10 different sounds for chime and siren modes- Advanced configuration available- Powerful long-lasting batteries – Z-Wave Plus with improved 500 chip for faster and safer wireless communication- Small size and quick installation Specifications:Model Number: ZSE33Z-Wave Signal Frequency: 908.42 MHzPower: 2 CR123 batteries (included)Power Consumption: 2WOperating Temperature: 32104 FRange: Up to 100 feet line of sightInstallation and Use: Indoor onlyDimensions: 2.7 x 1.2 Weight: 3 oz

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This
procedure should only be used when the primary controller is inoperable.

When your networks primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. To complete the process, make sure the Smart Chime is powered on, then PRESS AND HOLD the Z-Wave button for AT LEAST 10 SECONDS until the LED indicator flashes ONCE. Release the button. NOTE: All previously recorded activity and custom settings will be erased from the devices memory.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Inclusion

Auto Inclusion:1. Put your Z-Wave controller in inclusion mode2. Carefully remove the cover from the device3. Remove the plastic pull-tab from the battery slotthe Chime will automatically enter inclusion mode for 20 seconds4. A new alarm siren / doorbell device will appear on your controller’s device listManual Inclusion:1. Bring the Smart Chime within direct range of your controller2. Carefully remove the cover from the device3. Remove the plastic pull-tab from the battery slot. The LED indicator will blink slowly4. Put your Z-Wave controller in inclusion mode5. Press and release the Z-Wave button on the Smart Chime 3 TIMES quickly. The LED indicator will flash quickly6. A new alarm siren / doorbell device will appear on your controller’s device list (if it connects as an on/off switch, you may need to change the device type manually. Contact us for instructions).

Exclusion

1. Make sure the Smart Chime is powered on and located within direct range of your Z-Wave gateway controller2. Put your Z-Wave controller in exclusion mode3. Press and release the Z-Wave button 3 TIMES quickly. The LED indicator will flash quickly 4. The Smart Chime should disappear from your controller’s device listIf the first attempt is unsuccessful, please repeat the process following all steps carefully.

Communication to a Sleeping device (Wakeup)

This device is battery operated and turned into deep sleep state most of the time
to save battery life time. Communication with the device is limited. In order to
communicate with the device, a static controller C is needed in the network.
This controller will maintain a mailbox for the battery operated devices and store
commands that can not be received during deep sleep state. Without such a controller,
communication may become impossible and/or the battery life time is significantly
decreased.

This device will wakeup regularly and announce the wakeup
state by sending out a so called Wakeup Notification. The controller can then
empty the mailbox. Therefore, the device needs to be configured with the desired
wakeup interval and the node ID of the controller. If the device was included by
a static controller this controller will usually perform all necessary
configurations. The wakeup interval is a tradeoff between maximal battery
life time and the desired responses of the device. To wakeup the device please perform
the following action:

Press and release the Z-Wave button three times.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

1| 5| Z-Wave Plus Lifeline.Supported command classes:SWITCH_BINARY_REPORTNOTIFICATION_REPORTBATTERY_REPORTDEVICE_RESET_LOCALLY_NOTIFICATION
---|---|---
2| 5| Status notifications to Z-Wave devices associated in this group. Supported commandclasses:SWITCH_BINARY_REPORT
3| 5| Notifications to Z-Wave devices associated in this group. Supported command classes:NOTIFICATION_REPORT

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 1: Siren Volume

Choose from 3 volume levels for the alarm siren sound. Set volume to low, medium, or high.
Size: 1 Byte, Default Value: 3

SettingDescription

Parameter 2: Siren Alarm Duration

Choose from 5 modes to set the duration for siren alarm:0alarm is off1alarm goes off for 30 seconds2alarm goes off for 60 seconds3alarm goes off for 5 minutes255alarm continues until battery drains
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 3: Chime Sound Duration

_Choose how many times the chime should repeat the doorbell sound once triggered by a BASICSET alarm command from a door sensor.Values: 0chime is off, 1254 (cycles); 255chime sound continues until battery drains; 2default setting.
Size: 1 Byte, Default Value: 2

SettingDescription

Parameter 4: Chime Volume

Choose from 3 volume levels for the doorbell sound. Set volume to low, medium, or high.
Size: 1 Byte, Default Value: 3

SettingDescription

Parameter 5: Siren Alarm Tone

Choose one of the 10 different tones for alarm siren.
Size: 1 Byte, Default Value: 10

SettingDescription

Parameter 6: Chime Tone

Choose one of the 10 different tones for doorbell.
Size: 1 Byte, Default Value: 4

SettingDescription

Parameter 7: Siren Alarm or Chime Mode

Switch between Siren Alarm (configured by parameters 1, 2, 5, 8) and Chime / Doorbell (parameters 3, 4, 6, 9) modes.Values: 1Siren Alarm enabled; 2Chime enabled (default).
Size: 1 Byte, Default Value: 2

SettingDescription

Parameter 8: LED Notifications for Siren Alarm

Enable or disable visual alarm for Siren mode. The LED will blink when triggered.Values: 0LED disabled; 1LED enabled (default).
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 9: LED Notifications for Chime

Enable or disable visual alarm for Chime mode. The LED will blink when triggered.Values: 0LED disabled (default); 1LED enabled.
Size: 1 Byte, Default Value: 0

SettingDescription

Technical Data

Supported Command Classes

• Association Grp Info
• Association V2
• Basic
• Battery
• Configuration
• Device Reset Locally
• Manufacturer Specific V2
• Notification V6
• Powerlevel
• Switch Binary
• Version V2
• Zwaveplus Info V2

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>