PowerLocus P2 Kids Princess Bluetooth Headphones User Manual
- June 15, 2024
- PowerLocus
Table of Contents
PowerLocus P2 Kids Princess Bluetooth Headphones
For Warranty or Problems with the product, please contact us!
Email Support: info@powerlocus.com
PRODUCT INDICATION
- Power on /off
- play/pause, answer/end calls, reject call, last number redial
- + Volume up (Short Press) Next song (Long Press)
- – Volume down (Short Press) Last song (Long Press)
- Multi-function button(pairing,auto search radio)
- Headset jack
- LED indicator
- USB-C charging port
- Microphone
- Micro SD/TF card slot
Product Information|
---|---
Bluetooth Version:| V5.3
Impedance:| 32 Ohms
Working Distance Range:| 10M
Frequency Range:| 20Hz-20kHz
Weight:| 175g/0.39LBs
Audio Drivers:| 40mm
Charging Voltage:| DC 5V
Charging Time:| About 1.5 Hours
Talking/Music Time:| About 20 Hours (50% Volume)
POWER ON/OFF THE HEADSET
To power on the headset, press and hold the power button until the
indicator light turns on. To power off the headset, press and hold the power
button until the indicator light goes off.
- POWER ON: Slide the switch right and the blue and red indicator light will flash(the headset said:the wireless is ready to pair).
- POWER OFF: Slide the switch left and blue indicator light will go off.
PAIR TO YOUR MOBILE PHONE OR OTHER PRODUCTS
In Bluetooth mode, press the multi-function button to enter pairing mode. The headset will automatically search and connect to your phone or other products.
- Slide the switch right and the blue and red indicator light will flash(the headset said:the wireless is ready to pair ).
- Turn on the bluetooth function of your phone or other products.
- Search for the bluetooth devices and select”P2 Princess”. (Enter the code 0000′ if needed)
- If paring is successful, the blue light indicator starts flashing(the headset said: the wireless is connected successfully).
- Please make sure the headphone is working before pairing.
- It will connect to the pre-set phone automatically when turns on(Please make sure the bluetooth function of your phone is working)
- If the pairing is not successful, please switch off headset firstly, and then re-pair again.
MP3/FM MODE
To switch to MP3/FM mode, press the multi-function button. The headset will
automatically connect to your phone or other products.
- In power-on mode, insert the TF card, short press M button, MP3 will play automatically.
- If have not TF card, short press M button, FM radio will play automatically.
- (1) In power-on mode, short press button , FM radio will play automatically. (2) Long press the Play/Pause button to auto search all radio station, (3) wait for 40sec to 1min for the stations to be memorized, (4) then long press + or, – you will listen to any radio station you like..
- If you are listening to FM radio, short press M button, it will be converted to the bluetooth mode. And auto connected to your phone or other products.
ANSWER/END CALLS, REJECT CALL, LAST NUMBER REDIAL (In the Bluetooth
mode)
To answer a call, press the multi-function button. After the call, press
the multi-function button to hang up. If the other side hangs up, there is no
need to press the button. To reject a call, press and hold the multi-function
button for about 2-3 seconds. To redial the last number, press the multi-
function button twice.
- When there is a call, short press button can answer the call. After the call, press button can hang up. If the other side hang up, no need to press the button.
- reject call: long press button about 2-3sec.
- last number redial: press fast button 2 times
- When the phone call out or answer the call, if the bluetooth headphone are playing the music, the music will pause automatically and enter the waiting state. After hang up, the music will continue to play automatically.
CHARGING THE HEADSET
Connect the USB-C charging cable to the charging port on the headset and
the other end to a DC 5V power source. The indicator light will turn on during
charging and turn off when fully charged.
- Insert USB charging cable into USB port which have support 5V power (such as AC/DC USB adapter or PC USB port). When the red light is on, the headset is in charging. When the red light will be off, the headset is fully charged. It takes about 2-2.5 hours to charge the headset fully.
- The battery is rechargeable. Low-Voltage
alert: When the alert tone ‘low battery’ sounds and the indicator turns into red indicate that the battery has run out, need to be charged as soon as possible. First time charging : please be sure the battery has been charged fully before use.
WIRED HEADPHONE FUNCTION
You can connect one side of a 3.5mm stereo sound supply extension line to
the headphone audio jack and the other side to an audio jack on devices such
as a mobile phone, computer, or iPad to use the headset as wired headphones.
For any mode of headphone, you can connect one side of 3.5 stereo sound supply
extension line to headphone audio jack, the another side connect to Audio
jack(such as mobile phone, computer, Ipad etc).Then you will hear songs from
other devices.
Switch Mode – 85dB / 94dB
In order to change the volume sensitivity hold + and – button at the same time
till you hear the voice prompt “85dB” or “94dB”.
HOW TO RESET THE HEADPHONES?
To reset the headphones and enter pairing mode again, hold both buttons for
4-7 seconds.
- Hold both Buttons for 4-7 seconds in order to reset the bluetooth and enter pairing regime again.
FCC and ISED Canada Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This device
contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence exempt RSS(s).
Operation is subject to the following two conditions: this device may not
cause interference, and this device must accept any interference, including
interference that may cause undesired operation of the device.
Radiation Exposure: This equipment complies with Canada radiation
Exposure limits set forth for an uncontrolled environment to maintain
compliance with IC’s RF Exposure guidelines. This equipment should be
installed and operated with a minimum distance of 0mm from your body. This
device and its antenna(s) must not be co-located or operated in conjunction
with any other antenna or transmitter.
Warning
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
NOTE: This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter.
The device has been evaluated to meet general RF exposure requirement.
ISED Canada Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada ‘s licence exempt
RSS(s). Operation is subject to the following two conditions: this device may
not cause interference and this device must accept any interference, including
interference that may cause undesired operation of the device.
Radiation Exposure: This equipment complies with Canada radiation
Exposure limits set forth for an uncontrolled environment to maintain
compliance with IC’s RF Exposure guidelines. This equipment should be
installed and operated with minimum distance of 0mm the radiator your body.
This device and its antenna(s) must not be co-located or operation in
conjunction with any other antenna or transmitter.
CE
Hereby GL Grup-2015 LTD declares that wireless headphone PowerLocus P2 Kids is
in compliance with essential requirements and other relevant
conditions of Directive 2014/53/EU. The full text of the EU declaration
conformity is available at the following internet address: (powerlo-
cus.com/doc)
Frequency: 2402-2480 MHz
Max radio frequency power: 100 mW (EIRP)
GL GRUP-2015 LTD.
36 VASIL LEVSKI STREET, 5370 DRYANOVO, BULGARIA
UK
To find out more about the UK Declaration of Conformity, please visit:
https://powerlocus.com/doc-uk-p2kids
- This symbol on a product means that the product is covered by European Directive 2012/19/EU.
Electrical products should not be disposed of with household waste. Please
recycle them at the collect points provided for this purpose.
Contact the local authorities or your dealer for recycling advice. Proper
disposal of old appliances helps preserve the environment and health
Safety Instructions
- Please charge the headphones before first time using.
- Please charge at least once every 3 months to keep battery in good condition.
- To protect your hearing, please do not use the headphones long time with too high volume.
- Do NOT expose the headphone to hot temperature
- Protect from shocks and drops
- Do NOT try to open the product
- Do NOT expose to moisture, rain and liquids
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>