MiBOXER RGB+CCT LED Light WiFi 2.4G Instruction Manual

**MiBOXER RGB+CCT LED Light WiFi 2.4G

**

Product features

This product uses WiFi + Bluetooth + 2.4G wireless transmission technology, low power consumption, strong interference ability. WiFi + Bluetooth connect network can greatly enhance the connect network experience. When the router is disconnected, Bluetooth can also directly connect and control equipment at close range.

After successful network configuration using [Toya Smart] app to achieve wireless dimming, remote control, group control, scene control, Ming control, music movement, biorhythm, sleep plan, wake plan, one key execution, automation, etc. functions. And it supports 2.4G remote control.

• 16 Millions of colors to choose

• Color temperature adjustable

• Dim brightness / Saturation

• 2.4G RF wireless transmission technology

• WiFi wireless control support long-range control

• Auto-transmitting & Synchronization (only for remote control dimming)

• Device sharing

• Tap-to-Run & automation

• Timing setting / countdown turn on / off LED light

• DMX512 controllable (DMX512 LED transmitter is needed)

• Remote control Control distance 30m

• Smartphone app control

• Support third party voice control

• Group control

• Biorhythm

• Support music rhythm

• Sleep / wake up plan

• Support scene customization

• Do not disturb mode

Compatible with these 2.4G RF remote controls (Purchased separately)

• FUT100

• FUT089S

• FUT089 FUT089-B

• FUT088

• FUT092 FUT092-B

• FUT096 FUT096-B

• B8

• B0 / B0-B

• B4 / B4-B / T4
  

• B3 / B3-B / T3
  

• S2-B / S2-W S2-G

• FUTD01

2.4G RF Remote control instruction

Linking Code Instructions

1. Power off 10 seconds and power on again

2. Short press ” I ” button 3 times within 3 seconds.

3. Lights blink 3 times slowly means linking is done successfully.

 Linking failed if light is not blinking slowly, Please follow above steps again. (Note: Light that have linked can’t link again).

Unlinking Code Instructions

1. Power off 10 seconds and power on again

2. Short press ” I ” button 5 times within 3 seconds.

3. Lights blink 10 times quickly means unlinking is done successfully.

Auto transmi�ng & Synchroniza�on (only for remote control)

Remote signal auto transmi�ng

One light can transmit the signals from the remote control to another light within 30m, as long as there is a light within 30m, the remote control distance can be limitless.

Dynamic modes auto synchronization

Multi lights can synchronize if they are in same dynamic mode and linked with same remote (distance between each light is within 30m).

Dynamic mode table silicon (only for remote control)

Select dynamic mode table 1:
While the light is in static mode, short press “ S+ ” button 5 times quickly until blue light flashes 3 times slowly, static mode is activated successfully

Select dynamic mode table 2:
While the light is in static mode, short press “ S- ” button 5 times quickly until yellow light flashes 3 times slowly, static mode is activated successfully

Dynamic mode table 1 (default)

Dynamic mode table 2 (need to switch manually)

“Do Not Disturb” mode is activated and shut down (default activated)

Turn on “Do Not Disturb” mode (wide using in the area which have power failure frequently to save energy)

  2.4G RF Remote turn on and turn off instruction

  Turn on “Do Not Disturb” mode:

Press “OFF” button three times within three seconds and press “ON” button three times, Activated successfully once led light flashes four times quickly.

Attention: Do not disturb mode is activated

1. When the light is OFF stat us (For example: Use app or remote to turn off light) The light is OFF status once you t urn off power and t urn on again.
   (User must turn off and turn on power twice times to activate light or use APP/ remote to activate light]

2. When the light is ON status
   The light is ON 5tatus once you turn off and turn on power one time.

Turn off “Do Not Disturb” mode:

Press “ON” button t reed times within t here seconds and press “OF F” button t here times, closed successfully once led light flashes four times slowly.

Attention: The light will be always “ON” stat us if you t urn on and turn off power once user closed ”Do Not Disturb” mode.

App turn on and off •Do Not Disturb” mode instruction (check details in page 7)

Smartphone APP control instruction

  Network Configuration (Don’t support SG router)

  Download and install [Toya Smart] app

Search for [Toya Smart] in Apple or Google store or scan following QR code to download and instar II t he app. Please open t he app clit k ‘1 Register ” button to credited. account Wt.) le using t ln t heir stims, lapin direct lv if aula needy and account.

Network Configuration

1. Connect controller with power supply.

2. Confirm indicator light is flashing quickly (2 flashes per second),
   If indicator light isn’t in fast flashing state, there are two ways to enter:

   • Long press” SET” key until indicator light flashing quickly.
   • Power off and on controller 3 times.

3. Connect phone with home WiFi network in the 2.4GHz frequency.

4. Open homepage of app and click”+ ” button at the upper right corner of page.

5. Click” Lighting” on the left side of page and then click” Light Source (BLE+ Wi-Fi)”

6. Follow app prompts to complete configuration.

App turn on and off “Do Not Disturb” mode (default activated)

Click the light which need to be set up or group control — click “More” — click “Power-on behavior” –turn on or off.

Alexa voice control instruction

Please add device into [Tuya Smart] app (check details in page 6), then start following steps

1. Open Alexa App

2. Click “More” on the bottom of right corner

3. Click “Skills & Game
   

4. Click” 0.” on the top of right corner

5. Type into “Smart life” and search

6. Click “Smart Life” skill, follow instruction to finish configuration and start voice control

Google Home voice control instruction

Please add device into [Tuya Smart] app (check details in page 6), then start following steps

1. Open Google Home App

2. Click”+” on the top of left corner
   

3. Click “Set up device”

4. Click “Works with Google”

5. Click” 0.” on the top of right corner

6. Type into “Smart life” and search

7. Click “Smart Life” skill, follow instruction to finish configuration and start voice control

DMX512 LED Transmitter Control (Purchased separately)

DMX512 LED Transmitter Link/Unlink

1. Follow instruction of DMXS12 transmitter (FUTD01), Choose the zone for the light by pressing 11 + 11 or” – 11 (e.g. “CH1211 means zone 12)
   Link

2. The light is powered off for 10 seconds and then powered on,

3. Short press Ҥ11 3 times within 3 seconds while the indicator of controller is ON

4. Link is done once indicator of controller flashes 3 times slowly

Unlink

1. The lamp is powered off for 10 seconds and then powered on.
2. Short press “@” 5 times within 3 seconds while the indicator of controller is ON
3. Unlink is done once indicator of controller flashes 10 times quickly

 If the !ink or μn·link failed, please follow the above steps again.

Attention

1. Please turn off power supply before installation
2. Please ensure input voltage to be same as requirements from device
3. Don’t disassemble de¥ice if you are not expert, otherwise it will damage 1t.
4. Please do not use the light 1n the place with widely range metal area or “Strong electromagnetic wave nearby, otherwise, the remote distance will be seriously affected.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>