FLASH DJ Series RGB+W MINI LED Strobe User Manual
- June 13, 2024
- FLASH
Table of Contents
FLASH DJ Series RGB+W MINI LED Strobe
Symbols
WARNING! Use clamp to rig the fixture.
WARNING! When clamping the fixture to a truss or other structure at any
other angle than with the yoke hanging vertically downwards, use two clamps of
half-coupler type. Do not use any type of clamp that does not completely
encircle the structure when fastened.
WARNING! Position or shade the bar so that the front lens will not be
exposed to sunlight or any other strong light source from any angle – even for
a few seconds. See Figure 1. The LED STROBE lens can focused the sun’s
rays, creating a potential fire hazard and causing damage.
IMPORTANT! Do not point strong light output from other fixtures at the LED STROBE, as intense illumination can damaged the display.
INTRODUCTION
THANK YOU FOR PURCHASING LED STROBE. FOR SAFETY REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.
SAFETY INFORMATION
- Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.
- Unpack and check carefully there is no transportation damage before using the fixture.
- Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture.
- It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
- Disconnect main power before servicing and maintenance.
- Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
- Maximum ambient temperature is: 40°C Don’t operate it where the temperature is higher than this.
- In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself.
- Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
- Do not connect the device to any dimmer pack.
- Do not touch any wire during operation and there might be a hazard of electric shock.
- To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
- The housing must be replaced if they are visibly damaged.
- Do not look directly at the light spot while the fixture is on.
PRODUCT INFORMATION
- Light Source: 280×5050 RGB + 56×5050 White LEDs
- Power consumption: 40W
- Power supply voltage: 100-250V, 50/60Hz AC
- RGBW mixing, chose color temperature
- Operating modes: DMX512,Manual, Auto, Sound-controlled, Master/Slave,
- DMX channel mode 4/6/12/24/30
- IP Rating: IP20
- Housing made: Plastic+Alu
- Cooling: Active
- AC IN: IEC C13
- 3-Pin XLR DMX Input/Output
- Net Weight: 0.9 kg
- Net Dimensions: H(20)xW(38.5)xD(7) cm
- Pack Size: H(7)xW(27,5)xD(17) cm
INSTALATION
The unit should be mounted via its screw holes on the bracket. Always ensure
that the unit is firmly fixed to avoid vibration and slipping while operating.
Always ensure that the structure to which you are attaching the unit is secure
and is able to support a weight of 10 times of the unit’s weight. Also always
use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture. The equipment must be fixed by professionals. And it
must be fixed at a place where is out of the touch of people and has no one
pass by or under it.
The fixture may be installed in any orientation, but if installed horizontally
with a downward beam-angle, water can potentially pool in the fan wells. Under
normal operation the moisture will evaporate. However, in locations with high
rainfall, you may wish to fabricate a rain shield above the fixture, or modify
the position and orientation of the fixture to minimize pooling. Two quarter-
turn brackets are supplied with the fixtre if it is to be flown above the
ground. Rig the fixture to a support truss or structure using the supplied
brackets and suitable clamps. Fasten a safety cable between the support
structure and the attachment point on the fixture. The safety cable must be
able to bear at least 10 times the weight of the fixture.
The package includes:
❶ – LED STROBE (1 pc)
❷ – Power cable type IEC C13 (1 pc)
❸ – User Manual (1 pc)
CONNECTION
The device is equipped with the following interfaces:
- DMX (in/out): XLR 3(5)-pin socket
- Power (in): IEC C13 socket
The connection is performed using cable with XLR-female -> XLR-Male plugs.
CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120Ω resistor between signal (-) and signal (+) into a XLR plug and plug it in the DMX output of the last fixture.
Diagram of connection of devices by DMX cable.
The connection is performed using power cable with IEC C13 connector
(included). The device must be operated by qualified personnel.
CAUTION! In the case of cable damage do not attempt to repair.
Replacement or repair can be made only on the manufacturer or by a person with
appropriate permission
Using lamp, the change rate of power voltage should be within ±10%, if the voltage is too high, it will shorten the light’s life.
Voltage Specification.
| Input Voltage | Frequency | Total Power |
|---|---|---|
| 100-250 [V] AC | 50/60 [Hz] | 40 [W] |
Control Menu
- On the fixture display, four buttons from left to right:
- „MENU” button. It is the Function menu.
- „Up” button. Modify data up.
- „Down” button. Modify data down.
- „ENTER” button. Save the modified data and exit the edit state.
- In the editing state, if the „Enter” button is not pressed, the modified data will not be saved and will be lost after shutdown.
Display Function Menu
| No. | Content | Value | Function specification |
|---|---|---|---|
| 1 | A001 | 001-512 | The DMX512 address setting |
| 2 | 12CH | 4/6/12/24/30 | Channel mode setting |
| 3 | R255 | 000-255 | Red dimming, from dark to bright |
| 4 | G255 | 000-255 | Green dimming, from dark to bright |
| 5 | B255 | 000-255 | Blue dimming, from dark to bright |
| 6 | W255 | 000-255 | White dimming, from dark to bright |
| 7 | F000 | 000-255 | Total strobe, from slow to fast |
| 8 | AU01 | 01-08 | UP to switch the effect |
SP01-SP15
9| EF01| 00-20| UP to switch the effect| Press ENTER to set the speed
SP01-SP15
10| UF01| 00-45| UP to switch the effect| Press ENTER to set the speed
SP01-SP15
11| SU01| 01-03| Sound mode| Press ENTER to set the sensitivity SE01-SE15
DMX CHART
4 Channel Mode
| Channel | Value | Function Declaration |
|---|---|---|
| CH1 | 000-255 | R Red dimming, from dark to bright |
| CH2 | 000-255 | G Green dimming, from dark to bright |
| CH3 | 000-255 | B Blue dimming, from dark to bright |
| CH4 | 000-255 | W White dimming, from dark to bright |
6 Channel Mode
| Channel | Value | Function Declaration |
|---|---|---|
| CH1 | 000-255 | Total dimming, from dark to bright |
| CH2 | 000-255 | Total strobe, from slow to fast |
| CH3 | 000-255 | R Red dimming, from dark to bright |
| CH4 | 000-255 | G Green dimming, from dark to bright |
| CH5 | 000-255 | B Blue dimming, from dark to bright |
| CH6 | 000-255 | W White dimming, from dark to bright |
12 Channel Mode
| Channel | Value | Function Declaration |
|---|---|---|
| CH1 | 000-255 | Total dimming, from dark to bright |
| CH2 | 000-255 | RGB strobe, from slow to fast (W strobe by CH6) |
| CH3 | 000-005 | Perform the CH9-Ch11, RGB dimming |
| 006-010 | Static color, CH4 Select (R, G, B, W, yellow, purple, cyan) | |
| 011-015 | Breathing effect, CH5 Select color | |
| 016-020 | Jump change effect | |
| 021-025 | Gradient change effect | |
| 026-030 | Gradient change effect, CH5 Select color | |
| 031-040 | Auto run effect-1, CH5 Select color (cycle auto run) | |
| 041-050 | Auto run effect-2, CH5 Select color | |
| … | ||
| 211-220 | Auto run effect-19, CH5 Select color | |
| 221-229 | Auto run effect-20, CH5 Select color | |
| Channel | Value | Function Declaration |
| --- | --- | --- |
| 230-239 | Sound mode 1, CH5 Select color | |
| 240-249 | Sound mode 2, CH5 Select color | |
| 250-255 | Sound mode 3, CH5 Select color |
CH4
|
000-255
| Auto run effect: adjustment speed, from slow to fast. Sound mode: adjustment
sensitivity, from low to high (The highest sensitivity is the sensitivity set
by the menu).
CH5| 000-031| Default color
| 032-063| Red, CH3 Manual color selection
| 064-095| Green, CH3 Manual color selection
| 096-127| Blue, CH3 Manual color selection
| 128-159| Yellow, CH3 Manual color selection
| 160-191| Purple, CH3 Manual color selection
| 192-223| Cyan, CH3 Manual color selection
| 224-255| White CH3 Manual color selection
CH6| 005-255| W strobe, from slow to fast (RGB strobe by CH2)
CH7| 000-005| Perform the Ch12, W dimming
| 006-010| W effect-1 (cycle effect)
| 011-015| W effect-2 (W static effect)
| …|
| 221-255| W effect-44
| 226-255| W efect-45
CH8| 000-255| W effect adjustment speed, from slow to fast
CH9| 000-255| R Red dimming, from dark to bright
CH10| 000-255| G Green dimming, from dark to bright
CH11| 000-255| B Blue dimming, from dark to bright
CH12| 000-255| W White dimming, from dark to bright
24 Channel mode
| Channel | Value | Function Declaration |
|---|---|---|
| CH1 | 000-255 | R1 Red dimming, from dark to bright |
| CH2 | 000-255 | G1 Green dimming, from dark to bright |
| CH3 | 000-255 | B1 Blue dimming, from dark to bright |
| … | … | |
| CH 22 | 000-255 | R8 Red dimming, from dark to bright |
| CH 23 | 000-255 | G8 Green dimming, from dark to bright |
| CH 24 | 000-255 | B8 Blue dimming, from dark to bright |
30 Channel mode
| Channel | Value | Function Declaration |
|---|---|---|
| CH1 | 000-255 | Total dimming, from dark to bright |
| CH2 | 000-255 | Total strobe, from slow to fast |
| CH3 | 000-255 | R1 Red dimming, from dark to bright |
| CH4 | 000-255 | G1 Green dimming, from dark to bright |
| CH5 | 000-255 | B1 Blue dimming, from dark to bright |
| … | … | |
| CH24 | 000-255 | R8 Red dimming, from dark to bright |
| CH25 | 000-255 | G8 Green dimming, from dark to bright |
| CH26 | 000-255 | B8 blue dimming, from dark to bright |
| CH27 | 000-255 | W1 white dimming, from dark to bright |
| CH28 | 000-255 | W2 white dimming, from dark to bright |
| CH29 | 000-255 | W3 white dimming, from dark to bright |
| CH30 | 000-255 | W4 white dimming, from dark to bright |
Customer Support
FLASH-BUTRYM Sp.j.
Skarbimierzyce 18 · 72-002 Dołuje · POLAND
WWW.FLASH-BUTRYM.PL
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>