Pet Manka IPX7 Bark Collar with Auto Modes User Guide
- June 15, 2024
- Pet Manka
Table of Contents
Pet Manka IPX7 Bark Collar with Auto Modes
PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING
Package includes
- 1 x Remote Controller
- 1 x Receiver Collar
- 1 x Test Bulb
- 1x USB Charging Cable
- 2 x Sets of Contact Points
- 1 x User Manual
Overview
Remote Controller
Receiver Collar
How to replace the battery?
DESCRIPTION
- Vibration Button: By pressing the “Vibration” button, the receiver will vibrate.
- Shock Button: By pressing the “Static Shock” button, the receiver will emit a shock.
- AUTO Button: Tap the “AUTO” button, the receiver will change to automatic mode. By pressing and hold the “AUTO” button or set to level 0 to turn off automatic mode, the receiver screen will show “0”.
- Sensitivity Button: Tap the sensitivity button, ”S” mode will flash, can adjust the sensitivity for auto anti barking function.
- Beep Button: By pressing the “Beep” button, the receiver will emit a beep sound.
- + / – Buttons: Selects the level of the vibration and static Shock. It also selects the sensitivity of automatic mode.
- Turn on/off the Receiver: Turn on the receiver by pressing the “Power” button one time. Turn off the receiver by pressing the “Power” button twice.
FEATURES
-
Remote dog training and auto anti bark collar 2-in-1 system.
-
Remote range up to 50 meters /165ft /55 yard.
-
0-7 levels of vibration.(Level 7 is the strongest.)
-
0-7 levels of static shock.(Level 7 is the strongest.)
-
0-7 levels of sensitivity. (Level 7 is the highest sensitivity.)
-
Receiver is fully waterproof.
-
Rechargeable receiver.
-
Mini remote control, easy to carry.
-
Power saving design
- The Receiver Collar will enter STANDBY MODE if its not used for 5 minutes.
- Any movement will activate the Receiver Collar .
- The Controller will go into STANDBY MODE
if there is no operation after 30 seconds and can be activated by pressing any buttons.
-
2hours quick charge
-
Long standby time: The receiver’s battery can last for up to 7 days in standby time and 3-5 days in working time, and the remote can last up to 90 days in working time.
INSTRUCTIONS
Note: Please make sure the product is fully charged before using!
Please use 5V-Output charger only!
Pairing the remote controller and receiver
- Turn on the receiver (by pressing the “power” button one time)
- Long press the “power”button on receiver and the light will flash.
- After seeing light flash from the receiver, press the “Vibration button” within 30 seconds for pairing.
Adjusting the level of the vibration and shock
Press the “+” or “-” buttons to adjust the levels of vibration and shock modes
to get the perfect level that works best with your dog. (It is recommended to
use level 1-2 for electric shock)
How to change to automatic mode
Press the ”AUTO” Button on the remote, and the receiver screen will show “S”, at the same time the receiver will emit a “Beep Beep” sound which indicates that it is changed to automatic mode.
Adjusting the training function intensity under automatic mode
After entering into the automation mode, press down the “+” or “-” button on the controller to adjust the sensitivity and training intensity of vibration and shock to the level that best suits your dog. If you don’t want to give shock or vibration to the dog , you can set to level 0.
How to test automation mode
- Turn on the power.
- Set the sensitivity to Level 7. The electric shock intensity is greater than level 0.
- Please imitate the dog’s voice and shout “ah~~~ah” within the inductive zone of the bark stop collar, the sensor shall be triggered at this time. Since the frequency of human voice is different from that of dogs, if it is not triggered, please test it again.
- After the collar is triggered, the bark stop collar will first beep, then vibrate, and finally make electric shock.
- After testing, please configure an appropriate mode for your dog and follow the instructions that match your actual situation!
- We recommend that you do not use the shock mode at first.
We suggest working mode with beep+vibration to start training. If these functions do not stop your dog from barking, then use the shock mode. But please start with the lowest level and then gradually increase it according to your needs.
Note: Under automation mode, in order to ensure the safety of the dog, the product will enter the protected mode after work for 7 times consecutively in less than 90seconds. After a minute, the product re-enters the working mode. When in auto-protect mode, set the product back into working mode by pressing any button.
( Do not attach the dog leashes to this collar.The training collar is not a regular traction collar. Do not connect a leash directly to the training collar. Doing so during pulling may hurt the dog due to protruding the contact points and will directly damage the collar.)
IMPORTANT NOTES
- For the safety of your pet, the maximum amount of time you can press the vibration or static shock to your pet continuously is 15 seconds (in manual mode). After this, the vibration or static shock will stop, and the button must be released and pressed again.
- The transmitter will be changed to Standby Mode if there are no operations after 30 seconds. Press any button to take it out of the standby mode.
- The receiver will be changed to Standby Mode if there are no operations for five minutes. Any movements from the dog will activate the receiver.
- In working mode, if you want to reconnect the receiver to the transmitter, simply press the “Beep” button, there will be a beep sound indicating that it is ready to be matched.
- The design of the receiver is waterproof on level IP7 which makes the receiver fully waterproof. However, make sure your dog does not swim with it for too long to ensure that the nylon collar stays in good condition.
- The valid distance of the remote means the straight-line distance between the Transmitter and the Collar Receiver without obstacles in between. If there are interference signals or other disruptions, the actual remote control distance may vary.
- Training sessions should be kept positive and short, 10-15 minutes for each session is recommended.
- Presently, this product is the most effective and safest tool for training or barking prevention. When you follow the correct operational instructions, you can effectively train the pet without any problems.
- Once your pet is well trained you probably wont have to use this product on a regular basis. However, You may need to reinforce training with the Receiver Collar from time to time.
WARNINGS
- Make sure to read and follow the instructions carefully. It is important to use the collar correctly. Failure to do so may harm your pet.
- Do not use this product for your aggressive dog, or if your dog is prone to aggressive behavior. Aggressive dogs may cause damage to the people or things around. If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or certified trainer.
- Make sure the collar is not too tight on your dog, wearing a tight collar may cause skin damage.
- Avoid wearing the collar on the dog for more than 10 hours per day.
- If possible, reposition the collar every 1 to 2 hours.
- Never connect a dog rope or leash hook to the collar, it will cause excessive pressure on the contact area. And may cause skin damage or potentially harm your pet.
- Wash the neck area of your dog and the contact area of the collar weekly with a damp cloth.
- Examine the contact area of dog daily, lest rash or sore appears.
- If you see unusual conditions on your pets neck, immediately discontinue to use the product for a few days. If the condition persists beyond 48 hours, consult your veterinarian for help. Once the skin recovers, check the skin condition of your pet frequently
GENERAL TRAINING TIPS
The following tips will show you how to get the best performance out of your Dog Training Collar.
-
Make training sessions short and positive (about 10-15 minutes for each session.)
This will enable the dog to focus on the trainer. -
Training one dog each time is recommended.
-
During the first initial training sessions, keep the dog in a familiar outdoor environment.
Training in a place that the dog is not familiar with may make the dog become distracted. -
Use a long leash fastened to a non-metallic collar to help the dog to learn. Ensure that the additional collar and leash does not interfere with the Contact Points of the Collar Receiver. Do not use the remote training collar without a long leash unless your dog is fully trained.
-
More success will occur by teaching the dog a command first before trying to reinforce the command with the Remote Transmitter.
-
For basic obedience training, vibration is more useful.
-
Issue one obedience command each time, this will reduce confusion and allow the dog to remain focused. Do not use the training system for commands that the dog has not learned.
-
During training, look for all the positive changes in the dog’s behavior and remember to encourage it promptly with ample praise and reward.
-
Avoid over-correcting your dog. Use as less remote correction as possible during the training process.
-
When the dog has become apparently perplexed, shift the focus of the training by drawing the dog’s attention to a command they have been familiar with.Example: Tell the dog to sit and give abundant praise and encouragement on successful completion of the sit command.
-
Do not use the training system to correct or eliminate aggressive or biting behavior.
When the dog is showing signs of aggressive behavior, contact a professional dog trainer in your local area immediately. -
Please keep in mind that training sessions should be kept short. Stop Training and play with the dog when the dog has made progress.