VICTROLA VPT-1500 Hi-Res Onyx Bluetooth Turntable Wireless Record Player Instruction Manual

June 13, 2024
Victrola

VICTROLA VPT-1500 Hi-Res Onyx Bluetooth Turntable Wireless Record Player

Product Information

  • Product Name: HI-RES
  • Model: VPT-1500 / VPT-2500

Overview

  • Speed Selector
  • Slipmat Platter
  • Dust Cover
  • Top View
  • Cartridge Back View
  • 45 RPM Adaptor
  • Counter Weight
  • Anti-Skate Knob
  • Tonearm Lift Lever
  • Tonearm Holder
  • Tonearm
  • Removable Headshell
  • Control Button
  • RCA Output with Ground
  • Pre-Amp Switch
  • AC Power Port
  • Auto-Stop Switch

In the Box

  • Turntable
  • Dust Cover
  • Power Cord
  • RCA Cable
  • 45 RPM Counter Removable Adaptor Weight
  • Headshell
  • Platter
  • Silicone Slipmat
  • Cartridge (Recommended models and downforce numbers provided below)

Recommended Cartridge Models and Downforce Numbers:

  • Ortofon 2M Series: 1.6-2.0g
  • Audio Technica AT-VM95E Series: 1.8-2.2g
  • Ortofon OM Series: 1.5-2.0g

Specifications:

  • Power Input: AC 100-240V ~ 50HZ/60HZ
  • Bluetooth Version / Profile / Frequency: Bluetooth V5.4 / A2DP, AVRCP, aptXTM HD, aptXTM, SBC
  • Outputs: RCA (Built-in pre-amp)

Product Usage Instructions

  1. Connect the power cord to the AC power port.
  2. Connect one end of the RCA cable to the RCA output with ground.
  3. Connect the other end of the RCA cable to your audio device or amplifier.
  4. If using a Bluetooth-enabled device, pair it with the turntable using the appropriate Bluetooth version and profile.
  5. Place the slipmat on the platter.
  6. Place the desired cartridge on the tonearm and secure it using the removable headshell.
  7. Adjust the counterweight alignment by following the instructions provided. Use the downforce scale to set the appropriate weight for your cartridge model.
  8. Set the speed selector to the desired speed (33 RPM or 45 RPM).
  9. Use the control button to start and stop playback.
  10. Adjust the anti-skate knob to minimize tracking errors.
  11. Use the tonearm lift lever to raise and lower the tonearm.
  12. Place the tonearm holder in the rest position when not in use.
  13. When finished, use the dust cover to protect the turntable.

OVERVIEW

VICTROLA-VPT-1500-Hi-Res-Onyx-Bluetooth-Turntable-Wireless-Record-Player-
FIG-1

IN THE BOX

VICTROLA-VPT-1500-Hi-Res-Onyx-Bluetooth-Turntable-Wireless-Record-Player-
FIG-2 VICTROLA-
VPT-1500-Hi-Res-Onyx-Bluetooth-Turntable-Wireless-Record-Player-
FIG-3

SPECIFICATIONS

GENERAL

  • POWER INPUT:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 100-240V ~ 50HZ/60HZ
  • BLUETOOTH VERSION / PROFILE / FREQUENCY: . . . . . . Bluetooth V5.4 / A2DP, AVRCP 2.402GHZ-2.480GHZ
  • SUPPORTED BLUETOOTH CODECS: . . . . . . . . . . . . . . . . Qualcomm® aptX™ Adaptive, aptX™ HD, aptX™, SBC
  • OUTPUTS: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA (Built-in pre-amp) 200-280 MV (5 CM/SEC AT 1 KHZ-10DB) PHONO 2.5MV±3DB (5 CM/SEC AT 1 KHZ-10DB)
  • DIMENSIONS:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W 16.93” x L 14.25“ x H 4.53” W 430mm x L 362mm x H 115mm
  • WEIGHT: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VPT-1500: 5.66 kgs / 12.48 lbs (w/ cover) VPT-2500: 6.15 kgs / 13.56 lbs (w/ cover)
  • ACCESSORIES INCLUDED:. . . . . . . . . . . . . . . . . . . . . . . . . Dust Cover, 45 RPM Adapter, 6’ RCA cable with ground

TURNTABLE

  • DRIVE METHOD: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Belt-drive
  • PLATTER: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Die-cast aluminum
  • CARTRIDGE:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio Tecnhica VM95E (VPT-1500)
  • Ortofon 2M Red (VPT-2500)
  • MOTOR: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Servo-Controlled
  • SPEEDS: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-1/3 RPM & 45 RPM
  • PHONO PRE-AMP GAIN: . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 dB Nominal, RIAA Equalized
  • SIGNAL-TO-NOISE: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >45 dB
  • WOW & FLUTTER: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <0.175
  • TONEARM LENGTH: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225mm
  • OVERHANG: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.50mm
  • TRACKING ERROR ANGLE: . . . . . . . . . . . . . . . . . . . . . . . . <2 Degrees

AUTO – STOP SWITCH
ON: Platter will begin spinning when tonearm hovers over the edge of the record and stop spinning at the end of the record to prevent stylus wear.
OFF: Platter will spin when speed control is set to 33 or 45, regardless of tonearm position.

PRE-AMP SWITCH
LINE: Set the switch to line if connecting to line line-level input on speakers or amplifier. PHONO: Set the switch to phono if using external pre pre-amp or amplifier with phono input.

ADDITIONAL NOTES

  • Unit automatically powers off if no playback for 15 minutes.
  • Wired RCA output is disabled when mode is set to Bluetooth Out.
  • Unit automatically starts Bluetooth pairing when entering Bluetooth Out mode.
  • To reset the unit, press and hold the function button (5 seconds).
  • This will remove and forget all previously paired Bluetooth devices.

USER GUIDE
For user guide and more product information, please visit www.victrola.com /hi-res

WARNINGS

Important Safety Instruction

  1. Read these instructions – All the safety and operating instructions should be read before this product is operated.

  2. Keep these instructions – The safety and operating instructions should be retained for future reference.

  3. Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to.

  4. Follow all instructions – All operating and use instructions should be followed.

  5. Do not use this apparatus near water – The appliance should not be used near water or moisture – for example, in a wet basement or near a swimming pool, and the like.

  6. Clean only with dry cloth.

  7. Do not block any ventilation openings. Install in accordance with the manufacture’s instructions.

  8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

  9. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.

  10. Only use attachments/accessories specified by the manufacturer.

  11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

  12. Unplug the apparatus during lightning storms or when unused for long periods of time.

  13.  Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
    CAUTION/ATTENTION:
    RISK OF ELECTRIC SHOCK. DO NOT
    OPEN. / ATTENTION RISQUE DE

  14. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
    a. Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.
    b. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.

  15. This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.

  16. The mains plug is used as disconnect device, the disconnect device shall remain readily operable.

  17. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall not be placed on apparatus.

  18. The use of the equipment in moderate climate.

  19. WARNING: Please refer the information on exterior bottom/back enclosure for electrical and safety information before installing or operating the apparatus.

  20. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains etc.

  21. No naked flame sources, such as lighted candles, should be placed on the apparatus.

  22. Do not install this equipment in a confined space such as a book case or similar unit.

  23. The symbol with indicates AC voltage.

  24. CAUTION, These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

SAFETY INFO

Safety Information

  1. In order to shut off power to this product completely, unplug the power cord from the wall outlet. Be sure to unplug the unit if you do not intend to use it for an extended period of time, such as during a vacation.
  2. Use of controls, adjustments and performance of procedures other than those specified herein may result in hazardous radiation exposure.
  3. To prevent electric shock, match wide blade of plug to wide slot, fully insert.
  4. If this product is experience problems during operation, contact qualified service centers, and do not use the product in defective states.

Before Use

  1. Choose unit installation location carefully. Avoid placing it in direct sunlight or close to a source of heat. Also avoid locations subject to vibrations and excessive dust, cold or moisture. Keep away from sources that hum, such as transformers or motors.
  2. Do not open the cabinet as this may result in damage to the circuitry or electrical shock. If a foreign object should get into the set, contact Customer Service.
  3. Be sure not to handle record with dirty fingers. Never play a record that has a crack on the surface.
  4. When removing the power plug from the wall outlet, always pull directly on the plug, never pull the cord.
  5. To protect the stylus, don’t forget to put on the white protective needle cover after use.
  6. Do not attempt to clean the unit with chemical solvents as this might damage the finish. Use a clean, dry cloth.
  7. In order to shut off the power to this product completely, unplug the power cord from the wall outlet. Be sure to unplug the unit if you do not intend to use it for an extended period of time, such as a vacation.
  8.  Keep this manual in a safe place for future reference.

FCC & IC WARNINGS

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
The device must not be co-located or operating in conjunction with any other antenna or transmitter. To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.

IC Radiation Exposure statement
This device complies with RSS247 of Industry Canada. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
The device must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with IC radiation exposure limits set forth for an uncontrolled environment. The device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

WARRANTY

Victrola is a registered trademark of Innovative Technology Electronics, LLC.

United States
Victrola (Innovative Technology Electronics, LLC) warrants to the original retail purchaser that this product will be free from defective materials and workmanship for one (1) year from the date of purchase, subject to the limitations below. This warranty period is not extended if we replace the product. To obtain a replacement under the terms of this warranty, you must contact the dealer from which it was purchased with your original receipt. If assistance from the dealer from which it was purchased is impossible, you may contact our customer service for warranty assistance at victrola.com/contact. Except as limited below, if the product proves defective in either material or workmanship within one (1) year from the date of purchase, Victrola will replace the product at no charge. If the product model is no longer available and cannot be replaced with an identical model, Victrola will issue a merchandise credit for the purchase price to be redeemed at victrola.com.

Limitations:

  • This limited warranty does not cover failure of the product arising, in whole or in part, from improper installation, storage, transportation, misuse, abuse, accident, neglect, mishandling, unauthorized repair, modification, or wear from ordinary use or environmental deterioration.

  • This limited warranty does not cover cosmetic damage, including paint damage, or consequential damage to other components or premises which may result for any reason from the failure
    of the product.

  • This limited warranty is null and void for products not used in accordance with Victrola’s instructions.

  • This limited warranty terminates if the original retail purchaser sells or otherwise transfers this product.

  • This limited warranty is null and void for defects or damage caused by installation or repair performed by any person or entity other than a Victrola authorized installer or dealer.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state, jurisdiction to jurisdiction or country to country. All express and implied warranties for the product, including but not limited to any implied warranties of merchantability and fitness for a particular purpose, are limited in time to the term of this warranty. Some states, jurisdictions or countries do not allow the exclusion of certain implied warranties or conditions, or limitations on how long an implied warranty or condition lasts, so this limitation may not apply to you. Victrola’s responsibility for malfunctions and defects in hardware is limited to replacement or repair as set forth in this warranty statement. Victrola does not accept liability for special, punitive, consequential or incidental damages or losses, whether direct or indirect, including without limitation, any liability for third party claims against you for damages or losses or for products not being available for use. The maximum liability for which Victrola may be responsible will be no more than the amount you paid for the product that is the subject of the claim. Some states, jurisdictions or countries do not allow the exclusion or limitation of special, indirect, incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Canada and US Territories

  • The Warranty on this product shall comply with applicable law when sold to a consumer in Canada or a US Territory. To obtain any applicable warranty service, please contact the dealer from which you purchased the product, or the distributor that supplied the product, with your original receipt.
  • If assistance from the dealer from which it was purchased is impossible, you may contact our customer service for warranty assistance at victrola.com/contact.
  • If this product proves defective in either material or workmanship, Victrola will replace the product at no charge. If the product model is no longer available and cannot be repaired effectively or replaced with an identical model, Victrola at its sole option may replace the unit with a current model of equal or greater value.

Outside the U.S, Canada, and US Territories

  • The Warranty on this product shall comply with applicable law when sold to a consumer outside of the United States, Canada, and US Territories. To obtain any applicable warranty service, please contact the dealer from which you purchased the product, or the distributor that supplied the product, with your original receipt.
  • Please note: As a result of continual improvements, the design and specifications of this product are subject to change without notice.
  • Bluetooth is a registered trademark of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.
  • Qualcomm aptX is a product Qualcomm Technologies, Inc. and/or its subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.
  • aptX is a trademark of Qualcomm technologies International, Ltd., registered in the United States and other countries.
    Made In China.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Victrola User Manuals

Related Manuals