VIVOTEK AM-312 Mounting Adapter Installation Guide
- June 13, 2024
- Vivotek
Table of Contents
VIVOTEK AM-312 Mounting Adapter
Product Information
The VIVOTEK Mounting Accessories AM-312_V03_60MM Pole mount is a bracket designed to accommodate a pole with a diameter ranging from 55 ~ 89mm (2.16 ~ 3.5 inches). It is compatible with various VIVOTEK cameras and can be used for mounting purposes. The package contents include the pole mount bracket, stainless straps, screws, hex L wrenches, and other necessary items.
Compatible Cameras
| Compatible Brackets | Supported Cameras |
|---|---|
| AM-714 | IB9371-EHT/HT, IB9391-EHT |
| AM-719 | IB9371-(E)HT, IB9365-(E)HT, IB9365-(E)HT-A, IB9367-(E)H(T), |
IB8377-(E)HT, IB9391-EHT, IB9387-(E)H(T), IB9387-(E)HT-A
AM-218 (via AM-714/AM-719)| IB9365-EHT-A, IB9365-EHTV-v2, IB9367-(E)H(T),
IB9367-EHT-v2 (5-50MM), IB9367-EHT-v2, IB9380-H, IB9387-(E)HT-A, IB9388-HT,
IB9389-(E)H(M) T),IB9389EH(T)-v2, IB9391-EHT,IB9391-EHTV-v2, MS8391-EV,
MS9390-HV, TB9330-E, TB9331-E, MS9321-EHV
Corresponding ordering part numbers:
| AM-312_V03_60MM: VIO900000015 | AM-714: VIO100134800 |
|---|---|
| AM-218: VIO100146100 | AM-719: VIO100184500 |
Compatible VIVOTEK Cameras
| Compatible brackets | Supported Cameras |
|---|---|
| AM- 714 | IB9371-EHT/HT, IB9391- EHT |
| AM- 719 | **IB9371-(E)HT, IB9365-(E)HT, IB9365-(E)HT-A, |
IB9367-(E)H(T), IB8377-(E)HT, IB9391-EHT, IB9387-(E)H(T), IB9387-(E)HT-A
AM-218 (via AM-714/ AM-719)| Please refer to AM-218, AM-520, and
AM-525 documents.
Directly attached| IB9365-EHT-A, IB9365-EHTV-v2, IB9367-(E)H(T),
IB9367-EHT-v2 (5-50MM),**
IB9367-EHT-v2, IB9380-H, IB9387-(E)HT-A, IB9388-HT, IB9389-(E)H(M)(T),IB9389- EH(T)-v2, IB9391-EHT,IB9391-EHTV-v2, MS8391-EV, MS9390-HV, TB9330-E, TB9331-E, MS9321-EHV
The directly-attached configuration is less recommended for the lack of
waterproof and cabling protection. If directly attached, you should properly
wrap the rear-end cables and connectors with waterproof protection such as
putties.
Package Contents
- Pole mount bracket
- Stainless strap x2
- M6X20mm screws x4
- M5X20mm screws x4
- Hex L wrench 5mm x1
- Hex L wrench 4mm x1
- M4x15 screws x4
Mechanical Drawings
AM-312_V03_60MM Pole mount bracket
The pole mount bracket is designed to accommodate a pole in a diameter
ranging from 55 ~ 89mm (2.16 ~ 3.5 inches).
AM-312_V03_60MM Applications
- Make sure you have purchased the adequate accessories to be combined for your installation.
- Please do not install an indoor camera in an outdoor environment! Doing so will void our warranty. This is determined by whether the camera housing is weather-proof.
- Direct sunlight can tremendously increase the temperature within the device.
Installation
Below is a general, sample procedure using a Pole mount bracket:
- Pass the stainless steel straps through the bracket and around the pole.
- Tighten the straps using a pincer plier and a flat blade screwdriver.
- The 4 screw holes in the center are used for directly mounting the IB series bullet cameras. The 4 screw holes at the edges are used for mounting the AM-714 conduit box.
- Secure the AM-714 / AM-719 conduit box to bracket using the M5 screws, washers, and hex heads. A hex crescent wrench is required.
- For the rest of the installation procedure, refer to the documentation that came with the AM-714, AM-719, AM- 218, and the other accessories.
The 3/4″ cable glands and conduts for protecting cables are user-supplied.
Below are the corresponding mount holes for the MS9390-HV.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>