ZALMAN S3 ATX Mid Tower Gaming Case User Manual
- June 4, 2024
- ZALMAN
Table of Contents
- S3 ATX Mid Tower Gaming Case
- Precautions
- Specifications
- Accessories Component
- Separating the side panel
- Mounting the motherboard
- Mounting the 3.5″ and 2.5″ SSD / HDD
- Mounting 2.5″ SSD / HDD
- Mounting PCI-E(VGA) card
- Mounting the top fan
- Mounting the bottom fan
- Mountain the front fan and front radiator
- Cable Connection
- Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
User Manual
S3 ATX MID
TOWER COMPUTER CASE
KOR
S3 TG ATX MID TOWER COMPUTER CASE
Ver. 070720
S3 ATX Mid Tower Gaming Case
- To ensure safe and easy installation, please read the following precaution.
- Product design and specifications may be revised to improve quality and performance without notice.
Developed and designed by ZALMAN in Korea.
Th6 product 6 is protected by ZAIMAN’s pending or registered patents.
Precautions
- Read this manual carefully before installing.
- Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
- Wear gloves to prevent accidents when installing the product.
- Severe damage may occur when mounting the system, so do not apply excessive force.
- Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
- Be careful not to block the ventilation hole of the product when using the system.
- Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
- Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
- Do not insert your hand or another object into the product during operation, as this may injure your hand or damage the object.
- Store and use the product out of children’s reach.
- Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
- The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
Specifications
| Model | S3 | I S3(KOR) | I S3 TG |
|---|---|---|---|
| Case Form Factor | ATX Mid-Tower | ||
| Dimensions | 424(D) x 195(W) x 462(H)mm | 424(D) x 196(W) x 462(H)mm | |
| Weight | 3.7kg | I 3.8kg | 4.8kg |
| Case Materials | Steel, Plastic, Acrylic | Steel, Plastic, Tempered glass | |
| Motherboard Support | ATX / mATX / Mini-ITX | ||
| Maximum VGA Length | 330mm | ||
| Maximum CPU Cooler Height | 156mm | ||
| Maximum PSU Length | 180mm | ||
| PCI Expansion Slots | 7 | ||
| Case Drive Bays | 2 x 3.5″, 2 x 2.5″ | ||
| Fan Support | Front | 3 x 120mm | |
| Top | 2 x 120mm | ||
| Rear | 1 x 120mm | ||
| Bottom | 2 x 120mm | ||
| Fan(s) Included | Front | 2 x 120mm | |
| Rear | 1 x 120mm | 1 x 120mm | |
| Radiator Support | Front | 1 x 120mm | |
| Rear | 1 x 120mm | ||
| I/O Ports | 1 x Headphone, 1 x Mic, 2 x USB 2.0, 1 x USB 3.0 |
I/O Part
| # | Part | # | Part | # | Part | # | Part |
|---|---|---|---|---|---|---|---|
| A | Power button | B | Microphone jack | C | Headphone jack | D | USB 2.0 |
| E | USB 3.0 | F | Reset button | G | Power LED | H | HDD LED |
Accessories Component
Separating the side panel
Side Panel Removal
Mounting the motherboard
As 6 stand-offs are mounted by default, insert an additional stand-off according to the type of motherboard by referring to the mounting position of the main board, and mount the motherboard on the case.
Mounting the 3.5″ and 2.5″ SSD / HDD
Separate the 2.5° and 3.5″ combo HDD guide and assemble the HDD or SSD. Mount the assembled HDD on the slot.
Mounting 2.5″ SSD / HDD
2.5° SSD and HDDs can be installed on the right side of the case as shown in the diagram below.
Mounting PCI-E(VGA) card
Loosen the screw, separate the PCI cover, mount the graphic card, and fix it using the screw.
Mounting the top fan
As shown in the picture, install the fan on the top of the case using bolts
Mounting the bottom fan
Mountain the front fan and front radiator
After Front Cover Removal Mount the fan or the radiator on the mounting hole in the front as shown in the figure. (For liquid coolers, only products with a hose length of 240 mm or more can be installed)
Cable Connection
Warranty
10:00-17:00
10:00-16:00
www.zalmansvc.com
www.zalmansvc.com
MEMO
……………………………………..
………………………………………
……………………………………..
COOL INNOVATIONS
www.zalman.com
site: https://andpro.ru
+7 495-545-4870
email: info@andpro.ru
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>