FOR-X XQ-1000.1D Amplifiers Owner’s Manual
- June 13, 2024
- FOR-X
Table of Contents
FOR-X XQ-1000.1D Amplifiers
FRONT PANEL
XQ-1000.1D
XQ-225.2D/XQ-400.2D/XQ-550.2D
XQ-125.4D/XQ-225.4D/XQ-300.4D
XQ-1000.5D
GGIG GGGGGGL
ILLLL LEVEL (PRE IN/SPK IL)
FREQ CONTROL
FULL/HPF/LPF (BPF)
HPFCONTROL
LPF CONTROL
BASS BOOST CONTROL
INPUT
The amplifier support High/Low level RCA signal input. When choose PRE IN, Input sensitivity is 0.35-3.5V; When choose SPK IN, input sensitivity is 0.7-7V.
REAR PANEL
XQ-1000.1 D
XQ-225.2D/XQ-400.2D/XQ-550.2D
XQ-125.4D/XQ-225.4D/XQ-300.4D
XQ-1000.5D
GND
Used to connect power amplifier grounding cable. The power supply grounding
cable need lo be firmly connected lo the frame or the vehicle or other places
with good conduclivily.
Please use the cable with same specifications as the power supply cable and
connect to frame of the vehicle near the installation position of the power
amplifier. Please ensure that the grounding point is good and take appropriate
anti-oxidation measures.
REM
Remote control terminal. The remote control cable must be connected with source unit remote terminal so the amplifier will switch on and off automatically with source unit.
+12V
Used to connect the positive terminal 12V car battery. In order to ensure adequate power supply for the amplifier, special cable should be used to connect directly to the positive pole of the battery, and the fuse should be connected in series within 20 centimeters from the positive pole of the battery.
SPEAKER
Connect your speakers correctly which means plus to plus and minus to minus. Never connect speaker cables with chassis ground directly. It may destroy your amplifier.
Select cable and fuse according to the following table
Model| XQ-1000 .1D| XQ -225.20| XQ -400.20| XQ -550.20| XQ -125.4D| XQ
-225.4D| XQ-300 . 4D| XQ-1000.5D
---|---|---|---|---|---|---|---|---
Cable| 6 – BAW G| 6 – BAWG| 6 –
8AWG| 2 -4 AWG| 6-BAWG| 6-BAWG| 2-4AWG| 2-4AWG
Fuse| BOA| 60A| 1DOA| 180A| 60A| 100A| 1B0A| 100A
Power & speaker terminal size table
Power terminal XQ-1000.1 D
XQ-225 .2D
XQ-400.2D
XQ-125 .4D| 
---|---
Power terminal
XQ-550.2D
XQ-300.4D
XQ-1000.5D| 
---|---
Speaker terminal
XQ-125.4D
XQ-225.4D
XQ-300.4D| 
---|---
Speaker terminal
XQ-1000.1 D
XQ-225.2D
XQ-400.2D
XQ-550.2D| 
---|---
Speaker terminal
XQ-1000.5D| 
---|---
XQ-125.4D/XQ-225.4D/XQ-300.4D
XQ-125.4D/XQ-225.4D/XQ-300.4D
XQ-225.2D/XQ-400.2D/XQ-550.2D
XQ-225.2D/XQ-400.2D/XQ-550.2D
XQ-1000.1 D
XQ-1000.5D
SPECIFICATIONS
Model| I XQ-100 0 . 1D I| XQ-225 . 2D I|
XQ-400 .2 D I XQ-550.2D I XQ-125.4D I XQ-225.4D I
XQ-3 00 . 4D| XQ-1000 . 5D
---|---|---|---|---
RMS Power at 14.4V, 1KHz
2Ohm Load| 1000W X 1| 325W X 2| 600W X 2| 850Wx 2| 180W X 4| 300W X 4|
400Wx4| 150Wx4+400W
4Ohm Load| 665W X 1| 225W X 2| 400W X 2| 550Wx2| 125W X 4| 225W x4|
300Wx4| 100Wx4+250W
Bridged 4Ohm Load| NA| 650W X 1| 1200W X 1| 1700Wx 1| 360W X 2| 600W X 2|
&YJWx2| 300W x 2 + 250W
P eak Power 40hm Load| 2000W X 1| 650W X 2| 1200W X 2|
1700Wx2| 360W x4| 600W x4| &YJWx4| 300W x 4 + 800W
Features
Input Level| PRE INPUT : 0.35-3.5V / SPK INPUT: 0.7-7V
Frequency Response| 10Hz-25KHz| 10Hz-35KHz| 10Hz-30KHz| 10Hz-30KHz|
10Hz-30KHz 10Hz-30KHz| 10Hz-30KHz
X-over Type| HPF/FULL/BPF| HPF/FULL/BPF| HPF/FULL/BPF| HPF/FULL/BPF|
LPF/FULL/HPF LPF/FULL/HPF| LPF/HPF
LPF| OFF-300Hz| OFF-300Hz| OFF- 300Hz| OFF-300Hz| GROUP A: 0 – 300Hz / GROUP
B: 50Hz – 300Hz| SUB: 50-200Hz
Subsonic/HPF| OFF- 300Hz| OFF- 300Hz| OFF-300Hz| OFF- 300Hz| 50Hz – 300Hz|
Group A & B: 0- 200Hz; SUB: 0- 50Hz
Bass Boost Frequency| 40Hz| 40Hz| 40Hz| 40Hz| NA
NA NA| NA
Bass Boost Level| 0dB- 12dB| 0dB -12dB| 0dB -12dB| 0dB -12dB| NA
NA NA| NA
Intelligent Power
Management System
| Overload protection , Shortcircu it protect i on,
Overhea t protec ti on , Low voltage protect
i on, Over vo ltage pro t ec ti on
SIN Ratio| >96dB| >96dB| >95dB| >95dB| >95dB| >91dB I >93dB| >93dB
Min imum Load| 2Ohm| 2Ohm| 2Ohm| 2Ohm| 2Ohm| 2Ohm| 2Ohm
Voltage Range| 7.5V – 16V| 7.5V – 16V| 7.5V – 16V| 7.5V – 16V| 7.5V – 16V|
7.5V – 16V| 7.5V – 16V
Optiona l Bass Remote| YES| YES| YES| YES| NA| NA| YES
Components & PCB| SMT Parts / Double-Sided FR-4 PCB
DIMENSION
Height ( mm )| | | 46|
Width ( mm )| | | 155|
Length ( mm )| 186 I| 165 I| 186 I 226
I 165 I 186 I 256| 256
The contents of this manual the specifications of this product are subject to change without notice.
-
No Function:
Please check whether the power cable/ ground cable/ remote control cable connection is wrong. Make sure all connections are correct and in good contact. If the fuse is damaged, please pay attention to the correct value of a new fuse. -
No Sound:
Speaker cable or speaker plug are not connected correctly. No Sound /Red LED Protection Shines: The plus and minus wires of the speaker cable have contact, thus eliminate the short circuit. If you use a 2 Ohm speaker in stereo mode, a 4 Ohm speaker in. bridge mode or tri-mode and the set is overloaded, then turn the gain control to “min” until the operation is free of trouble. -
Poor Sound Quality (Distortions):
The speakers are overloaded, therefore turn down the volume level and check the volume control positions. -
No Stereo Sound And A Weak Bass:
Speaker cables(+) and(-) are mixed up, unit wired out of phase.
PRECAUTIONS
- This unit is designed for negative ground 12V DC operation only
- Avoid installing the unit where:
- It would be subject to high temperatures, such as from direct sunlight or hot air from the heater.
- It would be exposed to rain or moisture.
- It would be subject to dust or dirt.
- If your car is parked in direct sunlight and there is a considerable rise in temperature inside the car, allow the unit to cool off before operation.
- When installing the unit horizontally, be sure not to cover the heatsink fins with the floor carpet.
- If this unit is placed too close to the car radio, an interference may occur. In this case, separate the amplifier from the car radio.
- This power amplifier employs a protection circuit to protect the transistors and speakers if the amplifier malfunctions. Do not attempt to test the protection circuits by covering the heatsink or connecting improper loads.
- Do not use the unit with a weak auto battery as its optimum performance depends on a normal battery supply voltage.
- For safety reasons, keep the volume of your car audio system moderate so that you can still hear normal traffic sounds outside your car.
- If the product contains desiccant, do not eat, avoid touching the liquid, and keep away from children.
