FOR-X X-500DSP Car MP3 Radio Receivers User Manual

FOR-X X-500DSP Car MP3 Radio Receivers User Manual

WARNINGS & PRECAUTIONS

To avoid risk of serious injury or possble violation of laws, please read the following thoroughly before installation or connecting.

• This product is designed specifically for use with 12 volt, negative ground  electrical systems only.
• Having the wiring and installation done by expert.
• Be sure to disconnect the cable from the negative battery terminal while installation.
• This apparatus shall not be exposed to dripping or splashing, and no object filled with liquids, shall be placed on the apparatus.
• Fuses shall be replaced only with the correct type and fuse value, and only when the apparatus is powered off.
• To prevent a short circuit, never put or leave any metallic objects(such as coins or metallic tools)inside the unit.
• Never set the volume of this product so high that you cannot hear outside traffic and emergency vehicles.

PRODUCT FEATURES

LCD: VA-LCD
DSP: Built-in
Key Light : Multi Color
Bluetooth: Version 5.1
Remote: Support
Pre-Output: 6CH x 4V
Time Alignment: Support
AUX In: Support
SD Card: Support
Bluetooth Music : Support

EQ: 28 band/9 Preset
Radio: FM/AM/RDS
USB: Charge 2A
APP Control: iOS and Android Phone
Max Power: 4 x 60W
Subwoofer Control: Support
Dual Bluetooth Connection: Support
SWI Control: Support
Audio Format: MP3/WMA/AAC/FLAC
External Microphone : Support

INSTALLATION

Installation Procedures
First complete the electrical connections and then check for comectness.
Installation Opening
This unit can be installed in any dashboard Having an opening as shown below

To Install The Car Radio
Be sure you test all connections first, and then follow these steps to install this unit.

1. Make sure the ignition is Turned off, and then disconnect the cable from the vehicle battery’s negative (- terminal

2. Disconnect the wire harmess and the antenna.

3. Remove the detachable panel and decorative enclosure frame and place on one side.

4. insert the two brackets info the left and right sides of the chassis, as shown in the following figure, and separate the chassis from the sleeve.
   

5. insert the installation sleeve into the center console for be installed, and bend the clip using a screwdriver. Make sure the locking rod s flush with the mounting sleeve and does not protrude.

6. Connect cables as shown in the Wring diagram.

7. Insert the car radio into the mounting sleeve.

8. Install decorative enclosure frame .

ACCESSORY LIST

Please check the following accessories after opening the package:

1SO Male Connector x2

Diassemble keys x2

Remote x1

User Manual /Warranty Card Service Manual

DIMENSION(UNIT:MM)

WIRING DIAGRAM

POWER/SPEAKER CONNECTOR

Socket A (Power Supply)
A1: GND
A2: Ignition Wire
A3: NA
A4: Amplifier Control
A5: Battery(+)
A6: SWC/SWI Control Wire 1
A7: SWC/SWI Control GND
A8: SWC/SWI Control Wire 2

Socket B (Speakers):
B1: Rear Left (-)
B2: Rear Left (+)
B3: Front Left (-)
B4: Front Left (+)
B5: Front Right (-)
B6: Front Right (+)
87: Rear Right (-)
B8: Rear Right (+)

REMOTE OPERATION

**Install the battery

**

BLUETOOTH OPERATION

Bluetooth Pairing
The first time pair mobile phone with receiver please follow below steps:

1. When there is no pairing, in any mode, the BT on the LCD will flash, and the pairing can be performed at this time.
2. Turn on the phone’s Bluetooth to Search X-500DSP.
3. Click on the X-500DSP on the phone to connect. After the connection is successful, the BT wil stop flashing
4. When pairing is complete, the mobile phone audio will automatically transfer to the car audio system whenever a call is made or received, or when the mobile phone plays music.

Note
For more details of Bluetooth pairing, please refer to the owner’s manual for your mobile phone.

RADIO OPERATION

Start Listening

Europe Area: 87.5 ~ 108.0 KHz (50KHz / Step)
U.SA Area : 87.5~107.9 KHz (200 KHz / Step)
ASIA Area : 87.5~108.0 KHz (100 KHz / Step)
RUSS Area : 65.0 ~74.0 KHz (30 KHz/ Step)
Preset| 18FM / 12AM

USB &SD PLAYBACK

Track selection
Fast playback| Press

• Press and hold

Playback/Pause| Press 1
Track pre-play| Press INT 2

• Repeat playback Press 3 RPT

Repeat playback| Press 3 RPT

• REPEAT ONE.REPEAT DIR.REPEAT ALL

Random playback| Press RoM &

• ON/OFF

Folder selection| Press5 6

AUX INPUT

1. Connect a portable audio player(commercially available). Auxiliary input jack
   
   Auxiliary input jack 3.5mm stereo mini plug with “L”shaped connector. (commercially available).

2. Press[~/SRC]buttons to select AUX IN.

3. Turn on the portable audio player and start playback.

EXTERNAL MICROPHONE

Note
Since the panel microphone is far from the driver’s position, when using an external microphone, you can get better voice calls.

AUDIO SETTINGS

1. Press the knob to enter the [MENU]
2. Turn the knob to select [AUDIO], then press the knob.

Audio Settings List

30HZ/60HZ/80HZ/120HZ/160HZ/250HZ/400HZ/600HZ/
1.5KHZ/2KHZ/
2.5KHZ/3KHZ/
3.5K/4K/5K/6K/7K/8K/9K/11K/12K/13K/14K/15K/16K/17K/18K/19K
LOUD| OFF/ON
BASS| BASS -7 ~ +7
MIDDLE| MIDDLE -7 ~ 7
TONE| TONE -7 ~ 7
TREBLE| TREBLE -7 ~ +7
BALAN| BALAN L7-L0, 0, R1-R7
FADER| FADER R7-R1, 0, F1-F7
AUDIO RESET| NO/YES

Subwoofer Volume Adjustment

1. Turn the knob to select [SW LEVEL], then press the knob.
2. Turn the knob to adjustment SVOL [ -8 to +8]

Preset EQ Select

1. Turn the knob to select [PRESET EQ], then press the knob.
2. Turn the knob to select [USER/INATURALIPOP/CLASSIC/ROCK/ JAZZIFLATICOUNTRY/OPTIMAL]

User EQ Setup

1. Turn the knob to select [PRESET EQ], then press the knob.
2. Turn the knob to select [USER], then press the knob
3. Turn the knob to select frequency for adjustment\

Loudness Setup

1. Turn the knob to select [LOUNDY, then press the knob.
2. Turn the knob to select [OFF/ON]

Bass Adjustment

1. Turn the knob to select [BASS], then press the knob.
2. Turn the knob to adjustment [-7 to

AUDIO SETTINGS

Middle Adjustment

1. Tum the knob to select [MIDDLE], then press the knob.
2. Tum the knob to select [-7 to 7].

Tone Adjustment

1. Tum the knob to select [TONE], then press the knob.
2. Tum the knob to select [ -7 to +7].

Treble Adjustment

1. Tum the knob to select [ TREBLE ], then press the knob.
2. Tum the knob to select [-7 to +7].

Balance Adjustment

1. Tum the knob to select [BALAN], then press the knob.
2. Tum the knob to select | L7-L0 to R1-R7].

Fader Adjustment

1. Tum the knob to select [ FADER ], then press the knob.
2. Tum the knob to select [ R7-R0 to F1-F7].

Audio Setup Reset

1. Tum the knob to select [ AUDIO RESET ], then press the knob.
2. Tum the knob to select [NO/YES].

CLOCK AND DATE SETTINGS

1. Press the knob to enter the [MENU].
2. Turn the knob to select [CLOCK], then press the knob.

Clock And Date Settings List

Clock Format Settings

1. Turn the knob to select [CLK FRMT], then press the knob. 2. Turn the knob to select [12H/24H].

Clock Adjust

1.  Turn the knob to select [CLK ADJ], then press the knob.
2. Turn the knob to adjustment.
3. Press the knob to switch the clock/minute adjustment.

Date Format Settings

1. Turn the knob to select [DATE FORMAT], then press the knob.
2. Turn the knob to select [DD-MM-YY/MM-DD-YY].

Date Settings

1. Turn the knob to select [DATE SET], then press the knob.
2. Turn the knob to adjustment.
3. Press the knob to switch day/month/year adjustment.

XOVER SETUP

1. Press the knob to enter the [MENU].
2. Turn the knob to select [XOVER], then press the knob.
3. Turn the knob to select [SUB SET], then press the knob.

Subwoofer Xover List

OFF/30HZ/40HZ/50HZ/63HZ//80HZ/100HZ//125HZ/160HZ/200HZ/250HZ/
LPF FREQ| OFF/1KHZ/1.6KHZ/2.5KHZ/3.15KHZ/4K/5KHZ/ 6.3KHZ/8KHZ/10KHZ/12.5KHZ
SUB SET| FRQ THROUGH| 32HZ/40HZ/50HZ/63HZ/80HZ/100HZ/125HZ/160HZ/200HZ/250HZ
SW PHASE| NORMAL/REVERSE
SW GAIN| GAIN -8 ~ 8

Front &Rear HPF Frequency Setup 

1. Tum the knob to select [HPF FREQ 1, then press the knob.
2. Turn the knob to select frequency [OFF/30HZ/40HZ/50HZ/63HZ/70HZIB80HZ/ 90HZ/100HZ/125HZ/160HZ/180HZ/220HZ/250HZ/315HZ/400HZ/500HZI630HZ/ 700HZ/B00HZ]

Front &Rear LPF Frequency Setup

1. Tum the knob to select [LPF FREQ ], then press the knob.
2. Turn the knob to select frequency [FULLIK/1.6K/2.5K/3.15K/4K/5K/6.3K/8K/ 10K/12.5K]

Subwoofer Frequency Through Setup

1. Tum the knob to select [SW FRQ THROUGH , then press the knob.
2. Tum the knob to select frequency[32Hz/40Hz/50Hz/6 3Hz/80Hz/100HZ125Hz 160HZ/200H/250HZ/ ]

Subwoofer Phase Setup

1. Tum the knob to select [SW PHASE], then press the knob.
2. Turn the knob to select [NORMAL/REVERSE]

Subwoofer Gain Setup

1. Tum the knob to select [SW GAIN], then press the knob.
2. Turn the knob to select [0-5]

DTA SETTINGS

1. Press the knob to enter the [MENU].
2. Turn the knob to select [DTA SET], then press the knob.

DTA Settings List

Car Type Settings

1. Turn the knob to select [CAR TYPE], then press the knob.
2. Turn the knob to select [SMALL /MEDIUM/LARGE]

Listening Position Settings

1. Turn the knob to select [POSITION], then press the knob.
2. Turn the knob to select [USER/FRONT R/FRONT L/CENTER].

Delay Unit Settings

1. Turn the knob to select [UNIT], then press the knob.
2. Turn the knob to select [CM/MS/INCH].

DSP Reset

1. Turn the knob to select [DTA RST], then press the knob.
2. Turn the knob to select [NO/YES

ANIMATION SETTINGS

1. Press the knob to enter the [MENU].
2. Turn the knob to select [ANIMATION], then press the knob.
3. Turn the knob to select [OFF/PER 15SEC/30SEC/1MIN/2MIN/4MIN].

TIME ALIGNMENT(DISTANCE)

1. Press the knob to enter the [MENUJ]
2. Turn the knob to select [DTA SET], then press the knob
3. Turn the knob to select [DISTANCE], then press the knob.
4. Turn the knob to select[F LEFT/F RIGHT/R LEFT/R RIGHT/SUBWOOFER] to adjustment.

Determining the value for adjustment.

1. Determine the center of the currently set listening position as the reference point
2. The adjustable speaker has five directions: front left, front right, back left, back right, and back
3. The time for the speakers in the five directions to reach the center is the same by default.
4. Set the value for each speaker, the delay range: 0-20ms,
5. Adjust the increase or decrease of each speaker, 0.2ms each time. Example: When s selected as the listening position
   

TUNER SETTINGS

1. Press the knob to enter the [MENU]
2. Turn the knob to select [TUNER], then press the knob.

Tunner Settings List

SCIENCE/VARIED/POP M/ROCK M/EASY M/LIGHT M/CLASSICS OTHER M/WEATHER/FINANCE CHILDREN/SOCIAL/RELIGION PHONE IN/TRAVEL/LEISURE JAZZ/COUNTRY/NATION M OLDIES/FOLK M/DOCUMENT __
DX/LO C
| ARER EUROPE/USA/ASIA/RUSSIA
| RDS| | ON/OFF
| | TA ON/OFF   AF ON/OFF EON ON/OFF   REG ON/OFF  PTY OFF

Stereo/Mono Select
Turn the knob to select [STEREO or MONOY, then turn the knob select [STEREO/MONO] DX/Local Select
Turn the knob to select [LOC or DX, then tum the knob select [DX /LOCAL] Remark:  DX-Distant exchange
Tuner Area Select
Turn the knob to select [REGIONAL], then turn the knob select [ASIA/OIRT/EUR/USA] RDS ON/OFF Turn the knob to select
[RDS OFF],
then tur the knob select [RDS OFF,ON].

DEMO MODE SELECT

1. Press the knob to enter the [MENU]
2. Turn the knob to select [DEMO MODE], then press the knob.
3. Turn the knob to select [OFF/ON].

DISPLAY SETTINGS

1. Press the knob to enter the [MENU]
2. Turn the knob to select [DISPLAY], then press the knob.

Display Settings List

Spectrum ON/OFF

1. Turn the knob to select [SPECTRUM], then press the knob.
2. Turn the knob to select [OFF/ON].

ID3 ON/OFF

1. Turn the knob to select [ID3 TAG], then press the knob.
2. Turn the knob to select [OFF/ON].

Key Light Select

1. Turn the knob to select [MODE SEL], then press the knob.
2. Turn the knob to select [C-MODE 1/C-MODE 2/C-MODE 3].

Key Light Bright Setup

1. Turn the knob to select [BRIGHT], then press the knob.
2. Turn the knob to select [MANUAL], then press the knob.
3. Turn the knob to select [M-LEVER 1-8].
4. Turn the knob to select [AUTO], then press the knob.
5. Turn the knob to select [A-LEVER 1-8], then press the knob.
6. Turn the knob to select [START], then press the knob to setting start time.
7. Turn the knob to select [STOP], then press the knob to setting stop time.

System Version
Turn the knob to select [VERSION], then press the button to query the system version information.

TROUBLE SHOOTING

Not work
Fuse blown Loose panel contact
Not responding
System problem
No bass
Subwoofer setting level is too small
Can’t tum on voice
Bluetooth is not connected Phone does not support voice
Not playing
Incorrect device format Device error Unsupported audio file
Radio reception is poor
Poor contact of radio antenna Poor signal at location
Remote control is invalid
Remote control battery is low
Bluetooth call is poor
Microphone is too far away

Remedy
Replace the fuse: 10A(Red) Take out the panel and reinstall Reset the unit
Enter AUDIO to set SVOL
Connect Bluetooth NA
Reformat Replacement device Replace supported audio files
Reconnect the radio antenna Change to other positions
Replace CR2025 battery
Speak into the microphone

SPEAKER CONNECTION

Do not connect the speaker leads of the power cord to the car battery; other wise ,the unit will  be seriously damaged

Before oconnecting the speak leads of the power cord to the speakers, check the speaker wiring in your car.

SPECIFICATION

AM Frequency Range             522 KHz~1620 KHz
Preset
USB Index| Usable Audio Formats:| MP3/WMA
---|---|---
USB Port Type:| 2.0
USB Charging:| 5V/2A
Frequency Response:| 20 Hz – 20 KHz
S/N Ratio:| 60 dB
**BLUETOOTH**| Version| Bluetooth 5.1
---|---|---
BT Profile Supports:| A2DP, AVRCP, HFP
Range Of Frequency:| 2.4 GHz spectrum

APP CONTRO

APP Download
Please go to the APPLE APP Store or Google Play Store and search [AUDIO DSP Control] APP after downloading the APP ,install it on your Appale &Android devices.

APP Connection

1. Open the [AUDIO DSP Control] APP, click [ ] to search for X-500DSP.
2. Click X-500DSP to connect, the [ will be red after the connect is successful .

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>