FOR X XQ-7452DSP Digital Media Receiver Owner’s Manual

FOR X XQ-7452DSP Digital Media Receiver

 PRECAUTIONS

WARNINGS & PRECAUTIONS

To avoid the risk of serious injury or possible violation of laws, please read the following thoroughly before installation or connecting.

• This product is designed specifically for use with 12-volt, negative ground electrical systems only.
• Having the wiring and installation done by expert. Be sure to disconnect the cable from the negative battery terminal while installtion.
• This apparatus shall not be exposed to dripping or splashing, and no object filled with liquids shall be placed on the apparatus.
• Fuses shall be replaced only with the correct type and fuse value, and only when the apparatus is powered off.
• To prevent a short circuit, never put or leave any metallic objects(such as coins or metallic tools inside the unit.
• Never set the volume of this product so high that you cannot hear outside traffic and emergency vehicles.

PRODUCT FEATURES

INSTALLATION

First, complete the electrical connections and then check for correctness. Installation Opening This unit can be installed in any dashboard Having an opening as shown below

TO Install The Car Radio
Be sure you test all connections first, and then follow these steps to install this unit.

1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery’s negative (-) terminal.
2. Disconnect the wire harness and the antenna.
3. Remove the detachable panel and decorative enclosure frame and place on one side.
4. Insert the two brackets into the left and right sides of the chassis, as shown in the following figure, and separate the chassis from the sleeve.
5. Insert the installation sleeve into the centre console to be installed, and bend the clip using a screwdriver. Make sure the locking rod is flush with the mounting sleeve and does not protrude.
6. Connect cables as shown in the Wiring diagram.
7. Insert the car radio into the mounting sleeve.
8. Install decorative enclosure frame.

ACCESSORY LIST

Please check the following accessories after opening the package

DIMENSION(UNIT:MM)

WIRING DIAGRAM:

BASIC FUNCTIONS OF PANEL KEYS

REMOTE OPERATION

APP OPERATION
APP Download

• Method 1: Please scan the QR code on the cover to download the APP and install it on your Android or Apple device.
• Method 2: Please go to the APPLE APP Store or Google Play Store and search [AUDIO DSP Control] APP, after downloading the APP, install it on your Appale&Android devices.

APP Connection

1. Open the [AUDIO DSP Control] APP, click to search for XQ-7452DSP
2. Click XQ-7452DSP to connect, th will be red after the connection is successful.

RADIO OPERATION

Start Listening

USB &SD PLAYBACK

BLUETOOTH OPERATION

Bluetooth Pairing

The first time pair a mobile phone with the receiver, please follow below steps:

1. When there is no pairing, in any mode, the BT on the LCD will flash, and the pairing can be performed at this time.
2. Turn on the phone’s Bluetooth to Search XQ-7452DSP
3. Click on the XQ-7452DSP on the phone to connect. After the connection is successful, the BT will stop flashing.
4. When pairing is complete, the mobile phone audio will automatically transfer to the car audio system whenever a call is made or received, or when the mobile phone plays music.

Note:
For more details of bluetooth pairing, please refer to the owner’s manual for your mobile phone.

Bluetooth Basic Operation

Bluetooth Basic Operation

EXTERNAL MICROPHONE

Note:
Since the panel microphone is far from the driver’ s position, when using an external microphone, you can get better voice calls.

AUDIO SETTINGS

1. Press the knob to enter the [MENU].
2. Turn the knob to select [AUDIO], then press the knob.

Audio Settings List Subwoofer Volume Adjustment

1. Turn the knob to select [SW LEVEL], then press the knob.
2. Turn the knob to adjust SVOL [-8 to +8].

Preset EQ Select

1. Turn the knob to select [PRESET EQ ], then press the knob.
2. Turn the knob to select [USER/NATURAL/POP/CLASSIC/ROCK/ JAZZ/FLAT/COUNTRY/SUPER BASS].

User EQ Setup

1. Turn the knob to select [PRESET EQ ], then press the knob.
2. Turn the knob to select [USER], then press the knob.
3. Turn the knob to select a frequency for adjustment.

X-BASS Adjustment

1. Turn the knob to select [XBASS], then press the knob.
2. Turn the knob to adjustment [0-20].

Surround Setup

1. Turn the knob to select [SURROUND], then press the knob.
2. Turn the knob to select [OFF/ON].

Bass Adjustment

1. Turn the knob to select [BASS], then press the knob.
2. Turn the knob to adjustment [-7 to +7].

Middle Adjustment

1. Turn the knob to select [MIDDLE], then press the knob.
2. Turn the knob to select [ L7-LO to Rl-R7].

AUDIO SETTINGS

1. Press the knob to enter the [MENU].
2. Turn the knob to select [AUDIO], then press the knob.

Treble Adjustment

1. Turn the knob to select [TREBLE], then press the knob.
2. Turn the knob to select [-7 to +7].

Audio Setup Reset

1. Turn the knob to select [AUDIO RESET], then press the knob.
2. Turn the knob to select [NO/YES].

XOVER SETUP

1. Press the knob to enter the [MENU].
2. Turn the knob to select [AUDIO], then long press the knob enter the [XOVER]. Xover List

Xover List

XOVER SETUP

1. Press the knob to enter the [MENU].
2. Tum the knob to select [AUDIO], then long press the knob enter the [XOVER].

Xover List

XOVER SETUP

1. Press the knob to enter the [MENU].
2. Turn the knob to select [AUDIO], then long press the knob enter the [XOVER].

Xover List XOVER SETUP

1. Press the knob to enter the [MENU].
2. Turn the knob to select [AUDIO], then long press the knob enter the [XOVER].

Net 4.2 Front Setup

1.  Turn the knob to select [NET 4.2], then press the knob.
2. Turn the knob to select [FRONT], then press the knob.
3. Turn the knob to select [HPF FREQ/HPF SLOPE/LPF FREQ/LPF SLOPE/ PHASE/ GAIN], then press the knob.

Net 4.2 Rear Setup

1. Turn the knob to select [NET 4.2], then press the knob.
2. Turn the knob to select [FRONT], then press the knob.
3. Turn the knob to select [HPF FREQ/HPF SLOPE/LPF FREQ/LPF SLOPE/ PHASE/ GAIN], then press the knob.

Net 4.2 Subwoofer Setup

1. Turn the knob to select [NET 4.2], then press the knob.
2. Turn the knob to select [SUBWOOFER], then press the knob.
3. Turn the knob to select [LPF FREQ/LPF SLOPE/PHASE/GAIN], then press the knob.

Net 2-Way Tweeter Setup

1. Turn the knob to select [NET 2-WAY], then press the knob.
2. Turn the knob to select [TWEETER], then press the knob.
3. Turn the knob to select [HPF FREQ/GAIN LEFT/GAIN RIGHT], then press the knob.

Net 2-Way Front Setup

1. Turn the knob to select [NET 2-WAY], then press the knob.
2. Turn the knob to select [FRONT], then press the knob.
3. Turn the knob to select [HPF FREQ/HPF SLOPE/GAIN], then press the knob.

Net 2-Way Rear Setup

1. Turn the knob to select [NET 2-WAY], then press the knob.
2. Turn the knob to select [REAR], then press the knob.
3. Turn the knob to select [HPF FREQ/HPF SLOPE/GAIN], then press the knob.

Net 2-Way Subwoofer Setup

1. Turn the knob to select [NET 2-WAY], then press the knob.
2. Turn the knob to select [SUBWOOFER], then press the knob.
3. Turn the knob to select [LPF FREQ/LPF SLOPE/LPF PHASE/GAIN], then press the knob.

XOVER SETUP

1. Press the knob to enter the [MENU].
2. Turn the knob to select [AUDIO], then long press the knob enter the [XOVER].

Net 3-Way Tweeter Setup

1. Turn the knob to select [NET 3-WAY], then press the knob.
2. Turn the knob to select [TWEETER], then press the knob.
3. Turn the knob to select [HPF FREQ/HPF SLOPE/PHASE/GAIN LEFT/ GAIN RIGHT], then press the knob.

Net 3-Way Middle Setup

1. Turn the knob to select [NET 3-WAY], then press the knob.
2. Turn the knob to select [MIDDLE], then press the knob.
3. Turn the knob to select [HPF FREQ/HPF SLOPE/LPF FREQ/LPF SLOPE/ PHASE/GAIN ], then press the knob.

Net 3-Way Woofer Setup

1. Turn the knob to select [NET 3-WAY], then press the knob.
2. Turn the knob to select [WOOFER], then press the knob.
3. Turn the knob to select [HPF FREQ/HPF SLOPE/LPF FREQ/LPF SLOPE/ PHASE/GAIN ], then press the knob.

Net 3-Way Subwoofer Setup

1. Turn the knob to select [NET 3-WAY], then press the knob.
2. Turn the knob to select [SUBWOOFER], then press the knob.
3. Turn the knob to select [LPF FREQ/LPF SLOPE/PHASE/GAIN], then press the knob.

ANIMATION SETTINGS

1. Press the knob to enter the [MENU].
2. Turn the knob to select [ANIMATION], then press the knob.
3. Turn the knob to select [OFF/PER 15SEC/30SEq1MIN/2MIN/4MIN].

DEMO MODE SELECT

1. Press the knob to enter the [MENU].
2. Turn the knob to select [DEMO MODE], then press the knob.
3. Turn the knob to select [OFF/ON].

DTA SETTINGS

1. Press the knob to enter the [MENU].
2. Turn the knob to select [DTA SET], then press the knob.

DTA Settings List

DTA SETTINGS

1. Press the knob to enter the [MENU].
2. Turn the knob to select [DTA SET], then press the knob.

Car Type Settings

1. Turn the knob to select [CAR TYPE], then press the knob.
2. Turn the knob to select [SMALL /MEDIUM /LARGE].

Listening Position Settings

1. Turn the knob to select [POSITION], then press the knob.
2. Turn the knob to select [USER/FRONT R/FRONT L/CENTER].

Delay Unit Settings

1. Turn the knob to select [UNIT], then press the knob.
2. Turn the knob to select [MS/CM/INCH].

Distance Net 4.2 Settings

1. Turn the knob to select [DISTANCE], then press the knob.
2. Turn the knob to select [CHl~CHB], then press the knob.
3. Turn the knob to select[O~18.0MS/ 0~612CM/ 0~240 INCH].

Distance Net 2-Way Settings

1. Turn the knob to select [DISTANCE], then press the knob.
2. Turn the knob to select [CHl~CHB], then press the knob.
3. Turn the knob to select[0~18.0MS/ 0~612CM/0~240 INCH].

Distance Net 3-Way Settings

1. Turn the knob to select [DISTANCE], then press the knob.
2. Turn the knob to select [CHl~CHB], then press the knob.
3. Turn the knob to select[O~18.0MS/ 0~612CM/ 0~240 INCH]. www.for-x.com.tr

Note: Net 4.2/Net 2-Way /Net 3-Way can be set in the “XOVER” option.
DTA Reset

1. Turn the knob to select [DTA RST], then press the knob.
2. Turn the knob to select [NO/YES].

TIME ALIGNMENT(DISTANCE)

1. Press the knob to enter the [MENU].
2. Turn the knob to select [DTA SET], then press the knob.
3. Turn the knob to select [DISTANCE], then press the knob. www.for-x.com.tr
4. Turn the knob to select[F LEFT/F RIGHT/R LEFT/R RIGHT/SUBWOOFER] to adjust.

Determining the value for adjustment.

CD Determine the centre of the currently set listening position as the reference point.

• The adjustable speaker has five directions: front left, front right, back left, back right, and back.
• The time for the speakers in the five directions to reach the center is the same by default.
• Set the value for each speaker, the delay range: 0-20ms.
• Adjust the increase or decrease of each speaker, 0.2ms each time.

Example : When is selected as the listening position CLOCK AND DATE SETTINGS

1. Press the knob to enter the [MENU].
2. Turn the knob to select [CLOCK], then press the knob.

Clock And Date Settings List

Clock Format Settings

1. Turn the knob to select [CLK FORMAT], then press the knob.
2. Turn the knob to select [12H/24H].

Clock Adjust

1. Turn the knob to select [CLK ADJ], then press the knob.
2. Turn the knob to adjust.
3. Press the knob to switch the clock/minute adjustment.

Date Format Settings

1. Turn the knob to select [DATE FORMATI, then press the knob.
2. Turn the knob to select [DD-MM-YY/MM-DD-YY].

Date Settings

1. Turn the knob to select [DATE SET], then press the knob.
2. Turn the knob to adjust.
3. Press the knob to switch day/month/year adjustment.

TUNER SETTINGS

1. Press the knob to enter the [MENU].
2. Turn the knob to select [TUNER], then press the knob.

Tunner Settings List

TUNER SETTINGS

Stereo/Mono Select

• Turn the knob to select [STEREO or MONO], then turn the knob to select
• [STEREO/MONO].

DX/Local Select

• Turn the knob to select [LOC or DX], then turn the knob to select [DX /LOCAL].
• Remark: DX:Distant exchange.

RDS ON/OFF

• Turn the knob to select [RDS OFF], then tum the knob to select [RDS OFF, ON].

Tuner Area Select

• Turn the knob to select [REGIONAL], then turn the knob to select
• [ASIA/RUSSIA/EUR/USA].

DISPLAY SETTINGS

• Press the knob to enter the [MENU].
• Turn the knob to select [DISPLAY], then press the knob.

Display Settings List

Key Light Select

1. Turn the knob to select [COLOR SEL], then press the knob.
2. Turn the knob to select the key light colour: [AUTO/RED/GREEN /BLUE/YELLOW/CYAN/PURPLE/WHITE].

Spectrum ON/OFF

1. Turn the knob to select [SPECTRUM], then press the knob.
2. Turn the knob to select [OFF/ON].

ID3 ON/OFF

1. Turn the knob to select [ID3 TAG], then press the knob.
2. Turn the knob to select [OFF/ON].

System Version
Tum the knob to select [VERSION], then press the button to query the system version information

TROUBLESHOOTING

SPEAKER CONNECTION

Do not connect the speaker leads of the power cord to the car battery; otherwise, the unit wil be seriously damaged. Before oconnecting the speak leads of the power cord to the speakers, check the speaker wiring in your car

SPECIFICATION

www.for-x.com.tr

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>