FULLWAT LENNY-MD-087N Smart LED Control System Owner’s Manual
- June 13, 2024
- FULLWAT
Table of Contents
- Smart LED control system
- Technical specifications
- SINGLE COLOR
- Led Strip-controller connection
- System linking and unlinking
- Device auto-sync
- Auto-transmitting function **
- Battery installation – LENNY-MD-087
- Installation diagram – LENNY-TRIAC1
- Mobile phone pairing
- ALEXA linking
- GOOGLE HOME LINKING
- GOOGLE ASSISTANT linking
- Compatlbility table
- Table of controls by zones
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
remote control – 1 ZONE control
LENNY-MD-087
Smart LED control system
New smart LED color control system with 2.4GHz remote control.
Auto synchronisation and auto transmission functions.
The device adopts iow power consumption technologies and one controller can
manage several receivers at the same time.
The system does not produce interference as it uses a very low ievel
transmission signal.
Suitable for simpie installations in both Gomestic and professional
environments.
Owners manual
Technical specifications
Remote control
Model| LENNY-MD-087
Voltage| 3V (2 AM batteries)*
Emitting power| 6dBm
Standby current| 20uA
Working temperature| -10-40°C
Working frequency| 2.4GHz
Modulation type| GFSK
Aprox. operational distance| 30m
- Not inclued
DIRECT CURRENT DRIVERS
| LENNY-DRV-LS2 I I| LENNY-DRV-WL5| LENNY-DRV-WL2P
Description| 5 in 1 receiver| WiFi 5 in 1 receiver WiFi 2 in 1 receiver
Voltage| DC 12V–24V (terminal block & jack plug inputs)
Output max. current| 6A per channel| 12A per channel
Total current| 15A| 12A
Working temperatue| -20–60°C| -10-40°C
Working frequency| 2.4GHz
Aprox. operational distance| 30m
Connection mode| Common anode
WIFI| Requires gateway LENNY-WIFOX1| Included
ALTERNATE CURRENT DRIVER | TRIAC controller |
---|---|
Model | LENNY-TRIACI |
Input voltage | AC 100-240V 50/60Hz |
Output voltage | AC 100-240V |
Ouput current | MAX 1.36A |
Output power | 150W@100VAC; 300W@240VAC |
Regulation method | Wireless RF, push button, APP |
RF range | 30m |
Working temperature | -10-40°C |
WIFI | Requires gateway LENNY-WIFOX1 |
WIFI GATEWAY
Model| LENNY-WIFOX1
Working voltage| DC5V/500mA (Micro USB)
Working temperature| -20-60°C
Communication| VViFi-IEEE 802.11b/g/n 2.4GHz
Working frequency| 2.4GHz
Transmission power| 6dBm
- Suggested AC/DC adaptors (not included): MWMU10GS FU-ADPY10-5-USB
SINGLE COLOR
Remote control functions: LENNY-MD-087
| ON switch. Also used to link and unlink driver from this zone.
---|---
| OFF switch.
| Brigntness acijust.
Not3: Wetner control is inactive for 3 seconds, any mode is exited and
tne brightness requiation bar is activated.
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI
gateway is required, eltner bullt Into the receiver of using the LENNY-WIFOX1
gateway.
Led Strip-controller connection
Connection drawing
5 in 1 driver LENNY-DRV-LS2 / LENNY-DRV-WL5
Switch” button can be used to indicate which type of product Is being managed. To do so, press the “Switch” or “SET” button with a short touch until color from “indicator light” is required one.
| Single color| Tunable white| RGB| RGBW| RGBWW
---|---|---|---|---|---
Indicator light| | | | |
2 in 1 driver LENNY-DRV-WL2P
LENNY-TRIAC1 Push button control
Functioning
Short press: Switches the connected device ON/OFF.
Long press (press and hold): increases or decreases the intensity of the
light.
Connection
Tne maximum number of TRIACs is 25 pieces and maximum witing distance from the
push button is 20m.
To control everything with a single push button, LENNY-TRIACs must be
connected in cascade according to the connection diagram.
System linking and unlinking
Note: The light only works after the controller is paired with one or
more receivers.
Linking. Place Remote controller close to the desired driver to be paired.
Before starting linking process, configure receiver according to the type of
LED strip. Refer to “wiring diagram” section (previous point) from the manual.
-
Switch off power supply and after 10 seconds, switch tt on again.
Note: For LENNY-DRV-WL2P or LENNY-TRIAC 1, press the SET button once to enter pairing mode. -
Press ON button on the femote control 3 times within a maximum period of 3 sec.
-
The light will flash 3 times slowly to Indicate successful pairing.
If light does not flasn slowly, tne bonding is not done. Repeat the process until this occurs.
Unlinking
-
Switch off power supply and after 10 seconds, switch It on again.
Note: For LENNY-DRV-WL2P of LENNY-TRIAC1, press the SET button once to enter pairing mode. -
Press ON button on the femote control 5 times within amaximum period of 3 sec.
-
The light will flash 10 times quickly to indicate that unlinking is successful.
If light does not flash quickly, the bonding ts not done.
Repeat the process until this occurs.
Attention
-
Please check if input voltage is compatible with voltage supported by the driver. Pay special attention not to cross positive and negative poles.
Reversed connection will damage the controller. -
Do not connect the cables while the power supply is on. Tum it on when you are sure of connections are correct and there is no short circuit is possible.
-
Avoid placing driver controller in areas influenced by electromagnetic fields or close to devices that produceelectromagnetic fields. Also, do not place driver controller in areas shielded by metal surfaces or where metal surfaces come between the control and the controller.
This would affect operating distance effectiveness.
Device auto-sync
Different receiver drivers can be Connected to operate with the same remote
controller and operate in the same modes.
Notes:
- Self emitting indication.
- Remote driver controllers can be paired with the same remote controller within a maximum range of 30 meters. (possicle where as free of semi-free spaces and without too many obstacles of walls).
Auto-transmitting function **
**
A single remote controller may transmit control signals in succession to other diver controllers provided if maximum coverage distance of 30m Is respected between them.
Battery installation – LENNY-MD-087
- Open rear control unit cover.
- insert batteries conectty and close the covet
Installation diagram – LENNY-TRIAC1
Mobile phone pairing
Downlood and install the application on your mobile phone:
Note:
a Via QR Code
b. Searching the Play Store for *MiBoxer’.
https://www.futlight.com/app/1.html
Note:
Also compatible with the application: SMART LIFE
To link our installation with our mobile phone, we will need one of these
drivers:
~ LENNY-DRV-WL5
~ LENNY-DRV-WL2P
– LENNY-DRV-LS2 + LENNY-WIFOX1
– LENNY-TRIAC] + LENNY-WIFOX1
Register in MiBoxer:
We wil receive an e-mail with a
registation verification code, which we will have to enter in the application
to finish tagistering account.
In order to use the application, we must activate GPS on our mobile phone
(either Android or Apple}.
Once on the main screen and our session stared, we must add the device. To do
this:
Seleccionamos el tipo de dispositivo: For model
LENNY-DRV-WL5 :
Click on “Smart Strip Controller (WL5)”.
For model LENNY-DRV-WL2P:
Click on “LED controller (FUTO35W-FUTO39W)”.
For model LENNY-DRV-LS2 or model LENNY-TRIAC1:
Click on “2.4GHz Gateway (WL-Box1)”. For model LENNY-DRV-
WL5:
Disconnect power supply from LENNY-DRV-WLS5 for 10 sec.
After 10 seconds, power the controlier and within the fist three seconds,
press and hold “SET” button on the receiver until LED on the recetver flasnes.
For models LENNY-DRV-WL2P / LENNY-DRV-LS2 / LENNY-TRIAC 1:
Press SET button on device or on WIFI gateway for 3 seconds fo activate WIFI
signal.
In both cases, on the phone screen, click on “Ensure pilot lamp
blinking”.Enter network name and password.
Attention: only 2.4GHz network Is supporied (no 5G) and click on “Start
configuration”.
A countdown will appear and once paired, It will Indicate that pairing has
been successful.
Our device will appear in the list of paired devices.
Wether we have to use the WIFI gateway (LENNY-WIFOX1):
We must link the driver to be controlled via the APR
To do this, click on 2.4GHz gateway.
First we must choose whether we are going to configure one or more zones. In
this case, as It is a zone, we enter tne “change” section and select FUTOB7.
On the screen of our mobile phone we will see image as follows:
Click on “Link/uniink”.
Click on “link” fo tink and on “unlink” fo unlink.
Remove the power supply to controller for 10 seconds.
After 10 seconds, power the controller and In the first 3 seconds, click on
the mobile screen on “IInk” of “unlink”.
The light will flash three times and confirm correct linking.
In the case of unlink, light will fash 10 times for confimation.
The Gpplicalion GIOWs Us to CrEale Groups win ciferant racelvers. The wil GOW
Us IO COntO sevecds secevers at the same time: 1umn ON / OFF / change the
color, efc.
Once we have
Inked our receiver we can change our device name. The is Interesting we cre
gaing fo consol It wih Alexa, Google Assistant of Google Home.
To do 60, we press and hokd name of she device on the screen Onc Move It to
the teft We wil see an “edi and a “aalete”. Click On “El”, change the narne
and *OK°.
ALEXA linking
To control system with Alexa, a wifi gateway is required, either built into
receiver or using LENNY-WIFOX1 gateway. Install Alexa app and log in using
your account.
We need to install Mi-Light Smart skill. To do so:Once reached step as above, Alexa will defect our receiver
automatically and we will be able to change its name, include it in a group or
control it by voice.
If receiver is not detected automatically , we can push “detect devices” via
Alexa app function.
Now you can work with standard ALEXA managing.
We can rename device to be abie
to control that device only instead the whole group. command Alexa to tum
off/on the device, etc.
GOOGLE HOME LINKING
To control system with Google Home, a wifi gateway is required, either built
info the receiver of using LENNY-WIFOX1 gateway.
Install Google Home app and fog in with your Google account. If you have not
yet configured your home, you can do this now of later.
We need fo install MiLight Smart skill. To do this:
GOOGLE ASSISTANT linking
To control system with Google Assistant, a wifi gateway Is required, either
built into the receiver of using LENNY-WIFOX1 gateway.
And Install Google Assistant application via PlayStore on your phone:
‘We must configure it to recognize your
voice. Then enter “settings” in the application and click on “Voice Match’.
The application will ask you to repeat two phrases several times.
Once this is done, we will be able to “call” our device using “Ok Google”. For
example, “Ok Google turn on Fullwat* and LED strips connected to Fullwat
receiver will light up property.
Compatlbility table
| Single color| CCT| RGB| RGBW| RGBWW| “Mobile app
Alen
Google Home”| Zones
---|---|---|---|---|---|---|---
LENNY-DRV-1.52 LENNY-DRV-LS2S
5-in-1 standcrd recesver| LENNY-MD-085| LENNY-MD-085| | | | LENNYWIFOX1
gateway is required| 1
LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| 1
LEttly.mD.037| | | | | 1
LENNY-MD-088| LENNW-MD-088| LENNY-MD-088| LENNY-MD-038| LENNY-MD-088| 1
LENNY-PAN-00| LENNY-PAN-80| LENNY-PAN-80| LENNY-PAN-80| LENNY-PAN-80| 1
LENNY-PAN-Kl| LENNW-PAN-K1| | | | 1
LENNY-MD-007| LENNYMD-007| | | | 4
LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| 4
LENNY-PAN-B4| LENNY-PAN-84| LENNY-PAN-84| LENNY-PAN-84| LENWPAN-84| 4
LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| 8
LENNYPAN-B8| LENNY-PAN-88| LENNY-PAN-138| LENNY-PAN-B8| LENNY-PAN-88| 8
LENNY•DRY-WU
5 in 1 win receiver| LENNY-MD-085| LENNY-MD-085| | | | included| 1
LENNY-MD-086| LENNY-MD-086| LENNY-MD.086| LENNY-MD-086| LENNY-MD-086| 1
LENNY-MD-087| | | | | 1
LENNY-MD-088| LENNY-MD-088| LENNY-MD.088| LENNY-MD-088| LENNY-MD-088| 1
LENNY-PAN-BO| LENNY-PAN-BO| LENNY-PAN-80| LENNY-PAN-80| LENNY-PAN-80| 1
LENNY-PAN-Kl| LENNY-PAN-KI| | | | 1
LENNY-MD-W7| LENNY-MD-037| | | | 4
LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| 4
LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN.B4| LENNY-PAN-84| LENNY-PAN-B4| 4
LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| LENNY-MO-089| 8
LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-88| LENNY-PAN-68| LENNY-PAN-B8| 8
LENNY-DRV-WL2P
2 n 1 receiver with wifi and push button| LENNY-MD-085| LENNY-MD-085| | | |
hcbded| 1
LENNY-MD-086| LENNY-MD-086| | | | 1
LENNY-MD-I387| | | | | 1
LENNY-MD-088| LENNW-MD-088| | | | 1
LENNY-PAN-BO| LENNY-PAN-BO| | | | 1
LENNY-PAN-K1| LENNY-PAN-K1| | | | 1
LENNY-MD-007| LENNY-MD-007| | | | 4
LENNY-MD-092| LENNY-MD-092| | | | 4
LENNY-PAN-B4| LENNY.PAN-84| | | | 4
LENNY-MD-089| LENNY-MD-089| | | | 8
LENNY-PAN-B8| LENNY-PAN-88| | | | 8
LENNY-1RLAC1 Driver TRIAC| LENNY-MD-085| | | | | LENNY-VVFOX1 gateway is
required| 1
LENNY-MD-086| | | | | 1
LENNY-MD-087| | | | | 1
LENNY-MD-088| | | | | 1
LENNY-PAN-BO| | | | | 1
LENNY-PAN-Kl| | | | | 1
LENNY-MD-W7| | | | | 4
LENNY-MD-092| | | | | 4
LENNY-PAN-B4| | | | | 4
LENNY-MD-089| | | | | 8
LENNY-PAN-B8| | | | | 8
Table of controls by zones
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>