FULLWAT LENNY-MD-088B 1 Zone Remote Control Owner’s Manual

: June 13, 2024
: FULLWAT

FULLWAT LENNY-MD-088B 1 Zone Remote Control

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-PRODUCT

Product Information

Product Name: LENNY-MD-088 1 ZONE control
Product Type: Smart LED control system

Technical Specifications

Remote Control:
- Model: LENNY-MD-088
- Voltage: 3V (2 AAA batteries)*
- Emitting Power: 6dBm
- Standby Current: 20uA
- Working Temperature: Not specified
- Working Frequency: 2400-2483.5MHz
- Modulation Type: GFSK
- Aprox. Operational Distance: 30m
WIFI RECEIVER:
- Model: LENNY-WIFOX1
- Working Voltage: DC5V/500mA (Micro USB)
- Working Temperature: Not specified
- Communication: Not specified
- Working Frequency: Not specified
- Transmission Power: Not specified

Product Usage Instructions

To use the LENNY-MD-088 1 ZONE control Smart LED control system, follow these steps:

To control the LED lights using the remote control, make sure the remote control is powered by 2 AAA batteries (not included).
Point the remote control towards the LED lights and use the buttons to perform the desired actions.
To turn on the LED lights and exit programmed modes, press the ON switch or the White color direct ON button on the remote control.
To turn off the LED lights and exit programmed modes, press the OFF switch or the Exit button on the remote control.
To link or unlink the driver from this zone, press and hold the ON switch on the remote control.
To decrease the speed of programmed modes, use the corresponding button on the remote control.
To increase the speed of programmed modes, use the corresponding button on the remote control.

Note: For mobile control via mobile phone, Alexa, Google Home, or Google Assistant, a WIFI gateway is required. This can be either built into the receiver or using the LENNY-WIFOX1 gateway.

Smart LED control system

New smart LED color control system with 2.4GHz remote control.
Auto synchronisation and auto transmission functions.
The device adopts low power consumption technologies and one controller can manage several receivers at the same time.
The system does not produce interference as it uses a very low level transmission signal.
Suitable for simple installations in both domestic and professional environments.

Technical specifications

Remote control

DIRECT CURRENT DRIVERS

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-2

DIRECT CURRENT DRIVERS

WIFI

| Requires gateway LENNY-WIFOX1| Included

ALTERNATE CURRENT DRIVER TRIA Ccontroller

300W@240VAC

Regulation method| Wireless RF, push button, APP
RF range| 30m
Working temperature| -10-40ºC
WIFI| Requires gateway LENNY-WIFOX1

WIFI GATEWAY

Suggested AC/DC adaptors (not included): MWMU10GS
- FU-ADPY10-5-USB

SINGLE COLOR

Remote control functions: LENNY-MD-088

W: White color direct ON
- + Exit programmed modes.
ON: ON switch. Also used to link and unlink driver from this zone.
OFF: OFF switch.
M: Programmed modes.
- Exit from programmed modes, click on brightness bar or the W button.

Mobile control

For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI gateway is required, either built into the receiver or using the LENNY-WIFOX1 gateway.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-6

TUNABLE WHITE

Remote control functions: LENNY-MD-088

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-7

Mobile control

For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI gateway is required, either built into the receiver or using the LENNY-WIFOX1 gateway.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-8

RGB

Remote control functions: LENNY-MD-088

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-10

Working mode

Select color: Touch color wheel on desired color (e.g.blue).
Color saturation: Adjust color saturation (0% chosen color, 100% very saturated color).
Brightness bar: Adjust brightness level.
White: With any color selected from color wheel, click on “W” to set full white with R+G+B mixing.
- Brightness slide bar: White brightness level setting.
- Tunable white: Once white activated, use “color “saturation bar” to set different white tones from RGB leds mixing.

Mobile control

For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI gateway is required, either built into the receiver or using the LENNY-WIFOX1 gateway.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-11

Working mode

Select color: Touch color wheel on desired color (e.g. blue).
Saturation: Adjust color saturation (0% chosen color, 100% very saturated color).
Brightness level: Adjust brightness level.
White color: Bring out white color using R+G+B mixing combination (If maximum level is required, set saturation bar at highest level).
Tunable white: System allows to simulate dynamic white levels using RGB leds.

RGBW

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-12

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-13

Working mode

Select color: Touch color wheel on desired color (e.g. blue).
Brightness level: Adjust brightness level.
White activation only: Select color on the color wheel, push on “W” to set pure white.
Color+White activation: Set desired color on the color wheel then adjust white with saturation slide bar (0% on the left side, then white channel OFF, 100% on the right side, then white fully ON).
- Note: Once brightness level has been selected, if we push “W” then it will be switched ON at selected level.
Color + White and selected color cancelation: Push W.
Color + White and white setting cancelation: White channel slide bar on the left (0%).

Mobile control

For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI gateway is required, either built into the receiver or using the LENNY-WIFOX1 gateway.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-14

Working mode

Select color: Touch color wheel on desired color (e.g. blue).
“Saturation” bar: Adjust color saturation (0% chosen color, 100% very saturated color).
Brightness level: Adjust brightness level.
White light: Only white channel activation set.
- The “Brightness slide bar” is used to set desired brightness level.
Color + White activation: Choose color with “color slide wheel” and set white level with saturation bar (0% white channel off, 100% white channel set at max level).
Remove Color + white and Color levels: Press “White light”.

RGBWW

Remote control functions: LENNY-MD-088

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-15

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-16

Working mode

Select color: Touch color wheel on desired color (e.g. blue).
Brightness level: Adjust brightness level.
Dynamic white control: Press W key (if other color is selected previously, it will be switched off). Use slide touch “dynamic bar” until your get desired tone.
Color + White activation: Select desired white tone first (see previous steps). Once white shade tone is reached you must choose color using “color wheel”.
- Color + Dynamic white and white removing: Use “dynamic white” bar. 100% on the right (Selected white tone will be turn on at highest level) and 0% on the left (white color is turn off and color selected will remain).
- Color + Dynamic white and color removing: Press “W” key and set desired white tone.

Mobile control

For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI gateway is required, either built into the receiver or using the LENNY-WIFOX1 gateway.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-17

Working mode

Select color: Touch color wheel on desired color (e.g.blue)
Brightness level: Adjust brightness level.
Tunable white: Slide your finger over “tunable white bar” to get desired white tone.
- Note: If there is a previous selected level from color slide wheel, it will switch off.
Color + Dynamic White: Choose desired color with slide wheel and adjust white tone desired with saturation bar (0% white channel off, 100% white channel at highest level).
- Note: If dynamic white color is desired, please firstly set dynamic white mode.
Color + dynamic white and turn white off: Set saturation bar at lowest level 0%.
Color + dynamic white and color off: Select dynamic white tone with “Kelvin grade” bar and color will be switched off.

Led Strip-controller connection

Connection drawing

5 in 1 driver LENNY-DRV-LS2 / LENNY-DRV-WL5

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-18

“Switch” button can be used to indicate which type of product is being managed. To do so, press the “Switch” or “SET” button with a short touch until color from “indicator light” is required one.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-19

2 in 1 driver LENNY-DRV-WL2P

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-20

Press “SET” continuously to switch between single color and tunable white mode.

LENNY-TRIAC1 Push button control

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-21

Functioning

Short press: Switches the connected device ON/OFF.
Long press (press and hold): increases or decreases the intensity of the light.

Connection

The maximum number of TRIACs is 25 pieces and maximum wiring distance from the push button is 20m.
To control everything with a single push button, LENNY-TRIACs must be connected in cascade according to the connection diagram.

List of LENNY-DRV-LS2 modes and functions for RGB / RGBW / RGBWW

Number	Dynamic mode	Brightness / Saturation / Speed
1	Mardi Gras	****

Adjustable

List of LENNY-DRV-WL5 modes and functions for RGB / RGBW / RGBWW

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-22

System linking and unlinking

Note: The light only works after the controller is paired with one or more receivers.

Linking: Place Remote controller close to the desired driver to be paired.

Before starting linking process, configure receiver according to the type of LED strip. Refer to “wiring diagram” section (previous point) from the manual.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-23

Switch off power supply and after 10 seconds, switch it on again.
- Note: For LENNY-DRV-WL2P or LENNY-TRIAC1, press the SET button once to enter pairing mode.
Press ON button on the remote control 3 times within a maximum period of 3 sec.
The light will flash 3 times slowly to indicate successful pairing.

Warning: If light does not flash slowly, the bonding is not done. Repeat the process until this occurs.

Unlinking

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-24

Switch off power supply and after 10 seconds, switch it on again.
- Note: For LENNY-DRV-WL2P or LENNY-TRIAC1, press the SET button once to enter pairing mode.
Press ON button on the remote control 5 times within a maximum period of 3 sec.
The light will flash 10 times quickly to indicate that unlinking is successful.

Warning

If light does not flash quickly, the bonding is not done.
Repeat the process until this occurs.

Attention

Please check if input voltage is compatible with voltage supported by the driver. Pay special attention not to cross positive and negative poles. Reversed connection will damage the controller.
Do not connect the cables while the power supply is on. Turn it on when you are sure of connections are correct and there is no short circuit is possible.
Avoid placing driver controller in areas influenced by electromagnetic fields or close to devices that produce electromagnetic fields. Also, do not place driver controller in areas shielded by metal surfaces or where metal surfaces come between the control and the controller. This would affect operating distance effectiveness.

Device auto-sync

Device auto-sync

Different receiver drivers can be connected to operate with the same remote controller and operate in the same modes.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-25

Notes

: Self emitting indication.
Remote driver controllers can be paired with the same remote controller within a maximum range of 30 meters. (possible where as free or semi-free spaces and without too many obstacles or walls).

Auto-transmitting function

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-27

A single remote controller may transmit control signals in succession to other driver controllers provided if maximum coverage distance of 30m is respected between them.

Installation Diagram

Installation diagram – LENNY-TRIAC1

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-28

Mobile phone pairing

Download and install the application on your mobile phone:

Via QRl code
Searching the Play Store for “MiBoxer”.

Note: Also compatible with the application: SMART LIFE.

To link our installation with our mobile phone, we will need one of these drivers:

LENNY-DRV-WL5
LENNY-DRV-WL2P
LENNY-DRV-LS2 + LENNY-WIFOX1
LENNY-TRIAC1 + LENNY-WIFOX1

Register in MiBoxer:

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-30

We will receive an e-mail with a registration verification code, which we will have to enter in the application to finish registering account.
In order to use the application, we must activate GPS on our mobile phone (either Android or Apple).

Once on the main screen and our session started, we must add the device. To do this:

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-31

Select device model

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-32

For model LENNY-DRV-WL5:
- Click on “Smart Strip Controller (WL5)”.
For model LENNY-DRV-WL2P:
- Click on “LED controller (FUT035W-FUT039W)”.
For model LENNY-DRV-LS2 or model LENNY-TRIAC1:
- Click on “2.4GHz Gateway (WL-Box1)”.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-33

For model LENNY-DRV-WL5:
- Disconnect power supply from LENNY-DRV-WL5 for 10 sec.
- After 10 seconds, power the controller and within the first three seconds, press and hold “SET” button on the receiver until LED on the receiver flashes.
For models LENNY-DRV-WL2P / LENNY-DRV-LS2 / LENNY-TRIAC1:
- Press SET button on device or on WIFI gateway for 3 seconds to activate WIFI signal.

In both cases, on the phone screen, click on “Ensure pilot lamp blinking”.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-34

Enter network name and password.
Attention: only 2.4GHz network is supported (no 5G) and click on “Start configuration”.
A countdown will appear and once paired, it will indicate that pairing has been successful.
Our device will appear in the list of paired devices.

Wether we have to use the WIFI gateway (LENNY-WIFOX1):

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-36

We must link the driver to be controlled via the APP.
To do this, click on 2.4GHz gateway.
First we must choose whether we are going to configure one or more zones. In this case, as it is a zone, we enter the “change” section and select FUT088/B0.

On the screen of our mobile phone we will see image as follows:

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-37

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-38

Click on “Link/Unlink”.
Click on “link” to link and on “unlink” to unlink.
Remove the power supply to controller for 10 seconds.
After 10 seconds, power the controller and in the first 3 seconds, click on the mobile screen on “link” or “unlink”.
The light will flash three times and confirm correct linking.
In the case of unlink, light will flash 10 times for confirmation.

The application allows us to create groups with different receivers. This will allow us to control several receivers at the same time: turn ON / OFF / change the color, etc.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-39

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-40

Once we have linked our receiver we can change our device name. This is interesting if we are going to control it with Alexa, Google Assistant or Google Home.
To do so, we press and hold name of the device on the screen and move it to the left. We will see an “edit” and a “delete”. Click on “Edit”, change the name and “Ok”.

ALEXA linking

To control system with Alexa, a wifi gateway is required, either built into receiver or using LENNY-WIFOX1 gateway. Install Alexa app and log in using your account.

We need to install Mi-Light Smart skill. To do so:

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-41

Click on “more” and select “Skill and games”.
In the search engine type “Mi-Light Smart” and click on this option.
We allow application using.
Log in with your MiBoxer data.
If everything is correctly done, we will see a message of successful linking

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-42

Once reached step as above, Alexa will detect our receiver automatically and we will be able to change its name, include it in a group or control it by voice.
If receiver is not detected automatically , we can push “detect devices” via Alexa app function.
Now you can work with standard ALEXA managing.
We can rename device to be able to control that device only instead the whole group, command Alexa to turn off/on the device, etc.

GOOGLE HOME linking

To control system with Google Home, a wifi gateway is required, either built into the receiver or using LENNY-WIFOX1 gateway.
Install Google Home app and log in with your Google account. If you have not yet configured your home, you can do this now or later.

We need to install Mi-Light Smart skill. To do this:

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-44

Click on “more”.
Select “Configure device”.
Look for the “Mi-Light Smart” application in the list of applications.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-45

You may get a link warning message. Click on “Link” to accept.
Log in with your MiBoxer data.
If we do it correctly, a successful linking message will appear.

Once we have reached this point, the linking is done.

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-46

On the main Google Home screen, our home will appear with our device.
We can rename device to make “name it” easier.
Clicking on the device icon, you are reaching another page where you can control the lights too.

GOOGLE ASSISTANT linking

To control system with Google Assistant, a wifi gateway is required, either built into the receiver or using LENNY-WIFOX1 gateway.

And Install Google Assistant application via PlayStore on your phone:

FULLWAT-LENNY-MD-088B-1-Zone-Remote-Control-FIG-47

We must configure it to recognize your voice. Then enter “settings” in the application and click on “Voice Match”.
The application will ask you to repeat two phrases several times.
Once this is done, we will be able to “call” our device using “Ok Google”. For example, “Ok Google turn on Fullwat” and LED strips connected to Fullwat receiver will light up properly.