FULLWAT LENNY-MD-089N 8 Zones Smart LED Control System Owner’s Manual
- June 13, 2024
- FULLWAT
Table of Contents
- FULLWAT LENNY-MD-089N 8 Zones Smart LED Control System
- Product Information
- Product Usage Instructions
- Technical specifications
- SINGLE COLOR
- Mobile control
- TUNABLE WHITE
- RGB
- RGBW
- RGBWW
- Led Strip-controller connection
- List of LENNY-DRV-LS2 modes and functions for RGB / RGBW / RGBWW
- System linking and unlinking
- Device auto-sync
- Auto-transmitting function
- Installation diagram – LENNY-TRIAC1
- Mobile phone pairing
- ALEXA linking
- GOOGLE HOME linking
- GOOGLE ASSISTANT linking
- Documents / Resources
FULLWAT LENNY-MD-089N 8 Zones Smart LED Control System
Product Information
The LENNY-MD-089 is a smart LED control system that allows for remote control of up to 8 zones. It features a 2.4GHz remote control with auto synchronization and auto transmission functions. The system is designed with low-power consumption technologies and can manage multiple receivers simultaneously. Additionally, the system uses a very low-level transmission signal to avoid interference. It is suitable for both domestic and professional installations.
Technical Specifications
- Remote Control Model: LENNY-MD-089
- Voltage: Not specified
- Emitting Power: Not specified
- Standby Current: Not specified
- Working Temperature: Not specified
- Working Frequency: Not specified
- Modulation Type: Not specified
- Approx. Operational Distance: Not specified
Compatible Receivers
- LENNY-DRV-LS2: DC12V~24V, 6A per channel, Common anode
- LENNY-DRV-WL5: DC12V~24V, 12A per channel, WiFi 5 in 1 receiver
- LENNY-DRV-WL2P: DC12V~24V, 15A, WiFi 2 in 1 receiver
Alternate Current Driver
- Model: LENNY-TRIAC1
- Input Voltage: AC 100-240V, 50/60Hz
- Output Voltage: AC 100-240V
- Output Current: MAX 1.36A
WiFi Gateway
- Model: LENNY-WIFOX1
- Working Voltage: DC5V/500mA (Micro USB)
- Working Temperature: Not specified
- Communication: Not specified
- Working Frequency: Not specified
- Transmission Power: Not specified
Product Usage Instructions
To use the LENNY-MD-089 smart LED control system, follow these instructions:
Single Color Mode
- Use the brightness regulation bar on the remote control to adjust the brightness of the LED strip.
- Press the ON key to switch on the LED strips in all 8 zones, and press the OFF key to switch them off.
Zone Control
- Press the number keys (1-8) to select a specific zone.
- Press the ON key to switch on the selected zone, and press the OFF key to switch it off.
- To link or unlink a driver from a zone, press the selected zone ON key.
Programmed Modes
- Press the M key to access programmed modes.
- Press the W key to exit programmed modes.
- Use the S+ and S- keys to increase or decrease the speed of the programmed mode.
Note : Each zone requires a separate driver for control.
Smart LED control system
- New smart LED color control system with 2.4GHz remote control.
- Auto synchronization and auto transmission functions.
- The device adopts low power consumption technologies and one controller can manage several receivers at the same time.
- The system does not produce interference as it uses a very low-level transmission signal. Suitable for simple installations in both domestic and professional environments.
Technical specifications
Remote control
Model| LENNY-MD-089
Voltage| 3V (2 AAA batteries)*
Emitting power| 6dBm
Standby current| 20uA
Working temperature| -20~60°C
Working frequency| 2400-2483.5MHz
Modulation type| GFSK
Aprox. operational distance| 30m
DIRECT CURRENT DRIVERS
| LENNY-DRV-LS2| LENNY-DRV-WL5| LENNY-DRV-WL2P
Description| 5 in 1 in-receiver| WiFi 5 1 receiver| WiFi 2 1 receiver
Voltage| DC12V~24V (terminal block & jack plug inputs)
Output max. current| 6A per channel| 12A per channel
Total current| 15A| 12A
Working temperature| -20~60°C| -10~40°C
Working frequency| 2.4GHz
Approx. operational distance| 30m
Connection mode| Common anode
WIFI| Requires gateway LENNY-WIFOX1| Included
ALTERNATE CURRENT DRIVER | TRIAC controller |
---|---|
Model | LENNY-TRIAC1 |
Input voltage | AC 100-240V 50/60Hz |
Output voltage | AC 100-240V |
Ouput current | MAX 1.36A |
Output power | 150W@100VAC; |
300W@240VAC
Regulation method| Wireless RF, push button, APP
RF range| 30m
Working temperature| -10-40ºC
WIFI| Requires gateway LENNY-WIFOX1
WIFI GATEWAY
Model| LENNY-WIFOX1
Working voltage| DC5V/500mA (Micro USB)
Working temperature| -20~60°C
Communication| WiFi-IEEE 802.11b/g/n 2.4GHz
Working frequency| 2.4GHz
Transmission power| 6dBm
- Suggested AC/DC adaptors (not included): MWMU10GS
FU-ADPY10-5-USB
SINGLE COLOR
Remote control functions : LENNY-MD-089
To regulate LED strip, we must use the “brightness regulation” bar. Use “ON”
and “OFF” keys to switch LED strips on and off.
- Brightness control.
- 8 zones ON.
- 8 zones OFF.
- Exit programmed modes.
- Programmed modes.
- Selected zone ON.
- Also used to link and unlink drivers from this zone.
- Selected zone OFF.
Note : We need one driver per each zone we want to control.
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI gateway is required, either built into the receiver or using the LENNY-WIFOX1 gateway.
TUNABLE WHITE
Remote control functions: LENNY-MD-089
On the remote control, use the slide bar “dynamic white” to switch between
different white tones.
To regulate the LED strip, we must use the “brightness regulation” bar. Use
the “ON” and “OFF” keys to switch LED strips on and off.
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI
gateway is required, either built into the receiver or using the LENNY-WIFOX1
gateway.
RGB
Remote control functions: LENNY-MD-089
- Slide your finger over the coloured ring to change colors.
- Color brightness level and white changing.
- Color saturation level
- 8 zones ON.
- 8 zones OFF.
- White color output with R+G+B. combination.
- Dynamic modes.
- Under dynamic mode running, you can get light running faster with this switch.
- Under dynamic mode running, you can get slow speed with this switch.
- Selected zone ON. Also used to link and unlink drivers from this zone.
- Selected zone OFF.
Note : We need one driver at least per each zone we want to control.
Working mode
- Select color: Touch color wheel on desired color (e.g.blue).
- Color saturation: Adjust color saturation (0% chosen color, 100% very saturated color).
- Brightness bar: Adjust brightness level.
- White: With any color selected from color wheel, click on “W” to set full white with R+G+B mixing.
- Brightness slide bar: White brightness level setting.
- Tunable white: Once white activated, use “color “saturation bar” to set different white tones from RGB leds mixing.
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI
gateway is required, either built into the receiver or using the LENNY-WIFOX1
gateway.
Working mode
- Select color: Touch color wheel on desired color (e.g. blue).
- Saturation: Adjust color saturation (0% chosen color, 100% very saturated color).
- Brightness level: Adjust brightness level.
- White color: Bring out white color using R+G+B mixing combination (If maximum level is required, set saturation bar at highest level).
- Tunable white: System allows to simulate dynamic white levels using RGB leds.
RGBW
Remote control functions: LENNY-MD-089
- Slide your finger over the coloured ring to change colors.
- Color and white brightness control.
- With an active RGB colour, add “White” channel and dim only this one. In case you want to dim RGB and white at the same time, set white to maximum brightness and use the “brightness and dimming” bar.
- 8 zones ON.
- 8 zones OFF.
- Turn on white channel (from 4th channel). To dim the white, the “brightness and dimming” bar must be used. It is not possible to achieve white with the combination of R+G+B.
- Dinamic modes.
- Under dynamic mode running, you can get light running faster with this switch.
- Under dynamic mode running, you can get slow speed with this switch.
- Selected zone ON. Also used to link and unlink driver from this zone.
- Selected zone OFF.
Note : One driver is necessary per every zone.
Working mode
- Select color: Touch color wheel on desired color (e.g. blue).
- Brightness level: Adjust brightness level.
- White activation only: Select color on the color wheel, push on “W” to set pure white.
- Color+White activation: Set desired color on the color wheel then adjust white with saturation slide bar (0% on the left side, then white channel OFF, 100% on the right side, then white fully ON).
- Note: Once brightness level has been selected, if we push “W” then it will be switched ON at selected level.
- Color + White and selected color cancelation: Push W.
- Color + White and white setting cancelation: White channel slide bar on the left (0%).
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI
gateway is required, either built into the receiver or using the LENNY-WIFOX1
gateway.
Working mode
- Select color: Touch color wheel on desired color (e.g. blue).
- “Saturation” bar: Adjust color saturation (0% chosen color, 100% very saturated color).
- Brightness level: Adjust brightness level.
- White light: Only white channel activation set.
- The “Brightness slide bar” is used to set desired brightness level.
- Color + White activation: Choose color with “color slide wheel” and set white level with saturation bar (0% white channel off, 100% white channel set at max level).
- Color + tunable white and turn off white: We lower the saturation to 0%.
- Remove Color + white and Color levels: Press “White light”.
RGBWW
Remote control functions : LENNY-MD-089
- Slide your finger over the coloured ring to change colors.
- Color and white brightness control.
- With an active RGB colour, add “White” channel and dim only this one. In case you want to dim RGB and white at the same time, set white to maximum brightness and use the “brightness and dimming” bar.
- 8 zones ON.
- 8 zones OFF.
- Activates dynamic white channels. To adjust dynamic white, use the “dynamic white” slide bar until the desired color is achieved.
- If you want to adjust brightness, use the “brightness and dimming” slide bar. It is not possible to achieve white with an R+G+B combination.
- Dynamic modes.
- Under dynamic mode running, you can get light running faster with this switch.
- Under dynamic mode running, you can get slow speed with this switch.
- Selected zone ON. Also used to link and unlink drivers from this zone.
- Selected zone OFF.
Note : We need one driver at least per each zone we want to control.
Working mode
- Select color: Touch the color wheel on the desired color (e.g. blue).
- Brightness level: Adjust brightness level.
- Dynamic white control: Press W key (if another color is selected previously, it will be switched off). Use slide touch “dynamic bar” until you get the desired tone.
- Color + White activation: Select the desired white tone first (see previous steps). Once the white shade tone is reached you must choose color using “color wheel”.
- Color + Dynamic white and white removing: Use the “dynamic white” bar. 100% on the right (The selected white tone will be turned on at the highest level) and 0% on the left (the white color is turned off and the color selected will remain).
- Color + Dynamic white and color removing: Press the “W” key and set the desired white tone. (when you press “W” it will go to 100%)
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI
gateway is required, either built into the receiver or using the LENNY-WIFOX1
gateway.
Working mode
- Select color: Touch color wheel on desired color (e.g.blue)
- Brightness level: Adjust brightness level.
- Tunable white: Slide your finger over “tunable white bar” to get desired white tone.
- Note : If there is a previous selected level from color slide wheel, it will switch off.
- Color + Dynamic White: Choose desired color with slide wheel and adjust white tone desired with saturation bar (0% white channel off, 100% white channel at highest level).
- Note : If dynamic white color is desired, please firstly set dynamic white mode.
- Color + dynamic white and turn white off: Set saturation bar at lowest level 0%.
- Color + dynamic white and color off: Select dynamic white tone with “Kelvin grade” bar and color will be switched off.
Led Strip-controller connection
Connection drawing
5 in 1 driver LENNY-DRV-LS2 / LENNY-DRV-WL5
Press “SET” continuously to switch between single color and tunable white mode.
LENNY-TRIAC1 Push button control
Functioning
- Short press: Switches the connected device ON/OFF.
- Long press (press and hold): increases or decreases the intensity of the light.
Connection
- The maximum number of TRIACs is 25 pieces and maximum wiring distance from the push button is 20m.
- To control everything with a single push button, LENNY-TRIACs must be connected in cascade according to the connection diagram.
List of LENNY-DRV-LS2 modes and functions for RGB / RGBW / RGBWW
Number| Dynamic mode| Brightness / Saturation /
Speed
---|---|---
1| Mardi Gras| ****
Adjustable
2| Automatic colors changing
3| Sam
4| Gemma
5| Twlight
6| American
7| Super super Tuesday
8| Party
9| Splash colors
List of LENNY-DRV-WL5 modes and functions for RGB / RGBW / RGBWW
System linking and unlinking
Note : The light only works after the controller is paired with one or more receivers.
Linking
Place Remote controller close to the desired driver to be paired.
Before starting linking process, configure receiver according to the type of
LED strip. Refer to “wiring diagram” section (previous point) from the manual.
-
Switch off power supply andafter 10 seconds, switch it on again.
Note : For LENNY-DRV-WL2P or LENNY-TRIAC1, press the SET button once to enter pairing mode. -
Press ON button on the remote control 3 times within a maximum period of 3 sec.
-
The light will flash 3 timesslowly to indicate successful pairing.
Warning
- If light does not flash slowly, the bonding is not done.
- Repeat the process until this occurs.
Unlinking
-
Switch off power supply and after 10 seconds, switch it on again.
Note : For LENNY-DRV-WL2P or LENNY-TRIAC1, press the SET button once to enter pairing mode. -
Press ON button on the remote control 5 times within a maximum period of 3 sec.
-
The light will flash 10 times quickly to indicate that unlinking is successful.
WARNING
- If light does not flash quickly, the bonding is not done.
- Repeat the process until this occurs.
Attention
-
Please check if input voltage is compatible with voltage supported by the driver. Pay special attention not to cross positive and negative poles.
Reversed connection will damage the controller. -
Do not connect the cables while the power supply is on. Turn it on when you are sure of connections are correct and there is no short circuit is possible.
-
Avoid placing driver controller in areas influenced by electromagnetic fields or close to devices that produce electromagnetic fields. Also, do not place driver controller in areas shielded by metal surfaces or where metal surfaces come between the control and the controller.
This would affect operating distance effectiveness.
Device auto-sync
Different receiver drivers can be connected to operate with the same remote controller and operate in the same modes. ** Notes:**
- Self emitting indication.
- Remote driver controllers can be paired with the same remote controller within a maximum range of 30 meters. (possible where as free or semi-free spaces and without too many obstacles or walls).
Auto-transmitting function
A single remote controller may transmit control signals in succession to other driver controllers provided if maximum coverage distance of 30m is respected between them.
Installation diagram – LENNY-TRIAC1
Mobile phone pairing
Download and install the application on your mobile phone:
- a. Via QRl code
- b. Searching the Play Store for “MiBoxer”.
Note:
Also compatible with the application: SMART LIFE
To link our installation with our mobile phone, we will need one of these drivers:
- LENNY-DRV-WL5
- LENNY-DRV-WL2P
- LENNY-DRV-LS2 + LENNY-WIFOX1
- LENNY-TRIAC1 + LENNY-WIFOX1
Register in MiBoxer:
- We will receive an e-mail with a registration verification code, which we will have to enter in the application to finish registering account.
- In order to use the application, we must activate GPS on our mobile phone (either Android or Apple).
Once on the main screen and our session started, we must add the device. To do this:
Select device model:
- For model LENNY-DRV-WL5:
- Click on “Smart Strip Controller (WL5)”.
- For model LENNY-DRV-WL2P:
- Click on “LED controller (FUT035W-FUT039W)”.
- For model LENNY-DRV-LS2 or model LENNY-TRIAC1:
- Click on “2.4GHz Gateway (WL-Box1)”.
- For model LENNY-DRV-WL5:
- Disconnect the power supply from LENNY-DRV-WL5 for 10 sec.
- After 10 seconds, power the controller, and within the first three seconds, press and hold the “SET” button on the receiver until the LED on the receiver flashes.
- For models LENNY-DRV-WL2P / LENNY-DRV-LS2 / LENNY-TRIAC1:
- Press the SET button on the device or on the WIFI gateway for 3 seconds to activate the WIFI signal.
In both cases, on the phone screen, click on “Ensure pilot lamp blinking”.
-
Enter network name and password.
Attention: only 2.4GHz network is supported (no 5G) and click on “Start configuration”. -
A countdown will appear and once paired, it will indicate that the pairing has been successful.
Our device will appear in the list of paired devices.
Wether we have to use the WIFI gateway (LENNY-WIFOX1):
- We must link the driver to be controlled via the APP. To do this, click on the 2.4GHz gateway.
- First we must choose whether we are going to configure one or more zones. In this case, as it is a zone, we enter the “change” section and select FUT089/B8.
On the screen of our mobile phone, we will see the image as follows:
- Click on “Link/Unlink”.
- Click on “link” to link and on “unlink” to unlink.
- Remove the power supply to the controller for 10 seconds.
- After 10 seconds, power the controller, and in the first 3 seconds, click on the mobile screen on “link” or “unlink”.
- The light will flash three times and confirm the correct linking.
- In the case of unlink, the light will flash 10 times for confirmation.
The application allows us to create groups with different receivers. This will allow us to control several receivers at the same time: turn ON / OFF / change the color, etc.
- Once we have linked our receiver we can change our device name. This is interesting if we are going to control it with Alexa, Google Assistant or Google Home.
- To do so, we press and hold the name of the device on the screen and move it to the left. We will see an “edit” and a “delete”. Click on “Edit”, change the name and “Ok”.
ALEXA linking
To control the system with Alexa, a wifi gateway is required, either built
into the receiver or using the LENNY-WIFOX1 gateway. Install Alexa app and log
in using your account.
We need to install the Mi-Light Smart skill. To do so:
- Once reach the step as above, Alexa will detect our receiver automatically and we will be able to change its name, include it in a group or control it by voice.
If the receiver is not detected automatically, we can push “detect devices” via the Alexa app function.
Now you can work with standard ALEXA managing.
GOOGLE HOME linking
-
To control the system with Google Home, a wifi gateway is required, either built into the receiver or using LENNY-WIFOX1 gateway.
-
Install the Google Home app and log in with your Google account. If you have not yet configured your home, you can do this now or later.
We need to install the Mi-Light Smart skill. To do this:
Once we have reached this point, the linking is done.
GOOGLE ASSISTANT linking
- To control the system with Google Assistant, a wifi gateway is required, either built into the receiver or using LENNY-WIFOX1 gateway.
Install the Google Assistant application via PlayStore on your phone:
- We must configure it to recognize your voice. Then enter “settings” in the application and click on “Voice Match”.
- The application will ask you to repeat two phrases several times.
- Once this is done, we will be able to “call” our device using “Ok Google”. For example, “Ok Google turn on Fullwat” and LED strips connected to Fullwat receiver will light up properly.
Compatibility table
| ****
Single color
| ****
CCT
| ****
RGB
| ****
RGBW
| ****
RGBWW
| “Mobile app Alexa
Google Home”
| ****
Zones
---|---|---|---|---|---|---|---
LENNY-DRV-LS2 LENNY-DRV-LS2S
5-in-1 standard receiver
| LENNY-MD-085| LENNY-MD-085| | | | LENNY-WIFOX1
gateway is required
| 1
LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| 1
LENNY-MD-087| | | | | 1
LENNY-MD-088| LENNY-MD-088| LENNY-MD-088| LENNY-MD-088| LENNY-MD-088| 1
LENNY-PAN-B0| LENNY-PAN-B0| LENNY-PAN-B0| LENNY-PAN-B0| LENNY-PAN-B0| 1
LENNY-PAN-K1| LENNY-PAN-K1| | | | 1
LENNY-MD-007| LENNY-MD-007| | | | 4
LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| 4
LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN-B4| 4
LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| 8
LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-B8| 8
LENNY-DRV- WL5
5 in 1 wifi receiver
| LENNY-MD-085| LENNY-MD-085| | | | included| 1
LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| 1
LENNY-MD-087| | | | | 1
LENNY-MD-088| LENNY-MD-088| LENNY-MD-088| LENNY-MD-088| LENNY-MD-088| 1
LENNY-PAN-B0| LENNY-PAN-B0| LENNY-PAN-B0| LENNY-PAN-B0| LENNY-PAN-B0| 1
LENNY-PAN-K1| LENNY-PAN-K1| | | | 1
LENNY-MD-007| LENNY-MD-007| | | | 4
LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| 4
LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN-B4| 4
LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| 8
LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-B8| 8
LENNY-DRV- WL2P
2 in 1 receiver with wifi and push button
| LENNY-MD-085| LENNY-MD-085| | | | included| 1
LENNY-MD-086| LENNY-MD-086| | | | 1
LENNY-MD-087| | | | | 1
LENNY-MD-088| LENNY-MD-088| | | | 1
LENNY-PAN-B0| LENNY-PAN-B0| | | | 1
LENNY-PAN-K1| LENNY-PAN-K1| | | | 1
LENNY-MD-007| LENNY-MD-007| | | | 4
LENNY-MD-092| LENNY-MD-092| | | | 4
LENNY-PAN-B4| LENNY-PAN-B4| | | | 4
LENNY-MD-089| LENNY-MD-089| | | | 8
LENNY-PAN-B8| LENNY-PAN-B8| | | | 8
LENNY- TRIAC1
Driver TRIAC
| LENNY-MD-085| | | | | LENNY-WIFOX1
gateway is required
| 1
LENNY-MD-086| | | | | 1
LENNY-MD-087| | | | | 1
LENNY-MD-088| | | | | 1
LENNY-PAN-B0| | | | | 1
LENNY-PAN-K1| | | | | 1
LENNY-MD-007| | | | | 4
LENNY-MD-092| | | | | 4
LENNY-PAN-B4| | | | | 4
LENNY-MD-089| | | | | 8
LENNY-PAN-B8| | | | | 8
Table of controls by zones
Documents / Resources
|
FULLWAT LENNY-MD-089N 8 Zones Smart LED Control
System
[pdf] Owner's Manual
LENNY-MD-089N 8 Zones Smart LED Control System, LENNY-MD-089N 8, Zones Smart
LED Control System, Smart LED Control System, LED Control System, Control
System, System
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>