fullwat LENNY-MD-086 Smart LED Control System Owner’s Manual
- June 13, 2024
- FULLWAT
Table of Contents
fullwat LENNY-MD-086 Smart LED Control System
Smart LED control system
New smart LED color control system with 2.4GHz remote control. Auto
synchronisation and auto transmission functions. The device adopts low power
consumption technologies and one controller can manage several receivers at
the same time. The system does not produce interference as it uses a very low
level transmission signal. Suitable for simple installations in both domestic
and professional environments.
Technical specifications
Remote control
Model| LENNY-MD-086
Voltage| 3V (2 AAA batteries)*
Emitting power| 6dBm
Standby current| 20uA
Working temperature| -10~40°C
Working frequency| 2.4GHz
Modulation type| GFSK
Aprox. operational distance| 30m
- Not included.
DIRECT CURRENT DRIVERS
| LENNY-DRV-LS2| LENNY-DRV-WL5| LENNY-DRV-WL2P
Description| 5 in 1 receiver| WiFi 5 in 1 receiver| WiFi 2 in 1 receiver
Voltage| DC12V~24V (terminal block & jack plug inputs)
Output max. current| 6A per channel| 12A per channel
Total current| 15A| 12A
Working temperatue| -20~60°C| -10~40°C
Working frequency| 2.4GHz
Aprox. operational distance| 30m
Connection mode| Common anode
WIFI| Requires gateway LENNY-WIFOX1| Included
ALTERNATE CURRENT DRIVER TRIAC controller
Model| LENNY-TRIAC1
Input voltage| AC 100-240V 50/60Hz
Output voltage| AC 100-240V
Ouput current| MAX 1.36A
Output power| 150W@100VAC;
300W@240VAC
Regulation method| Wireless RF, push button, APP
RF range| 30m
Working temperature| -10-40ºC
WIFI| Requires gateway LENNY-WIFOX1
WIFI GATEWAY
Model| LENNY-WIFOX1
Working voltage| DC5V/500mA (Micro USB)
Working temperature| -20~60°C
Communication| WiFi-IEEE 802.11b/g/n 2.4GHz
Working frequency| 2.4GHz
Transmission power| 6dBm
- Suggested AC/DC adaptors (not included): MWMU10GS FU-ADPY10-5-USB
SINGLE COLOR
Remote control functions: LENNY-MD-086
Note: Wether control is inactive for 3 seconds, any mode is exited and the brightness regulation bar is activated.
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI
gateway is required, either built into the receiver or using the LENNY-WIFOX1
gateway.
TUNABLE WHITE
Remote control functions: LENNY-MD-086
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI
gateway is required, either built into the receiver or using the LENNY-WIFOX1
gateway.
RGB
Remote control functions: LENNY-MD-086
- ON switch. Also used to link and unlink driver from this zone.
- OFF switch.
- Touch colour ring.
Color setting
Push icon twice to enter COLOR REGULATION mode. To change color type, use
TOUCH COLOR RING.
Once color is selected:
- Push once on brightness icon and use TOUCH COLOR RING to adjust brightness.
- Push twice on BRIGHTNESS icon and use TOUCH COLOR RING to adjust saturation color level.
Programmed modes
To access stock color modes, long press ON icon .
- Check different stock color modes is possible with short press on ON icon.
- To adjust BRIGHTNESS level: short press on icon and using COLOR RING. Exit from stock modes: double click on COLOR REGULATION palette icon .
White
Reaching WHITE color using RGB, press once on the palette icon and use COLOR
RING. Exit from “white mode”: double click on palette icon .
Note: Wether control is inactive for 3 seconds, any mode is exited and the brightness regulation bar is activated.
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI
gateway is required, either built into the receiver or using the LENNY-WIFOX1
gateway.
Working mode
- Select color: Touch color wheel on desired color (e.g. blue).
- Saturation: Adjust color saturation (0% chosen color, 100% very saturated color).
- Brightness level: Adjust brightness level.
- White color: Bring out white color using R+G+B mixing combination (If maximum level is required, set saturation bar at highest level).
- Tunable white: System allows to simulate dynamic white levels using RGB leds.
Remote control functions: LENNY-MD-086
- ON switch. Also used to link and unlink driver from this zone.
- OFF switch.
- Touch color ring.
- White
White channel control: press once on palette icon .
• To change white brightness, click on BRIGHTNESS icon and use TOUCH COLOR RING.
• Exit from “ white mode”: press twice on palette icon .
- White
Color change
Press twice on palette icon to enter in TOUCH COLOR REGULATION mode. Use TOUCH
COLOR RING to change color.
- Press once on BRIGHTNESS icon and use “WHEEL” to change level.
- Press twice on BRIGHTNESS icon and use “WHEEL” to saturation level.
Note: Wether control is inactive for 3 seconds, any mode is exited and the brightness regulation bar is activated.
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI
gateway is required, either built into the receiver or using the LENNY-WIFOX1
gateway.
Working mode
- Select color: Touch color wheel on desired color (e.g.blue).
- Saturation: Adjust color saturation (0% chosen color, 100% very saturated color)
- Brightness level: Adjust brightness level.
- White light: To turn on white channel only.
- Brightness slide bar is used to set bright level.
- Color + White activation: Choose color with “color slide wheel” and set white level with saturation bar (0% white channel off, 100% white channel set at max level).
- Remove Color + white and Color levels: Press “White light”.
RGBWW
Remote control functions: LENNY-MD-086
- ON switch. Also used to link and unlink driver from this zone.
- OFF switch.
- Touch color ring.
Tunable white
To activate dynamic white mode, press once on palette icon .
-
* White color changing: click on brightness icon and slide finger over TOUCH COLOR RING- White color mode exit: click twice on palette icon .
Color changing
Press twice on palette icon to activate “color variation” mode. Slide your
finger over TOUCH COLOR RING to change desired color. Once color is selected,
click once on brightness icon and slide your finger over TOUCH COLOR RING to
get desired brightness level.
Note: Wether control is inactive for 3 seconds, any mode is exited and the brightness regulation bar is activated.
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI
gateway is required, either built into the receiver or using the LENNY-WIFOX1
gateway.
Working mode
- Select color: Touch color wheel on desired color (e.g.blue)
- Brightness level: Adjust brightness level.
- Tunable white: Slide your finger over “tunable white bar” to get desired white tone.
- Note: If there is a previous selected level from color slide wheel, it will switch off.
- Color + Dynamic White: Choose desired color with slide wheel and adjust white tone desired with saturation bar ( 0% white channeloff, 100% white channel at highest level).
- Note: If dynamic white color is desired, please firstly set dynamic white mode.
- Color + dynamic white and turn white off : Set saturation bar at lowest level 0%.
- Color + dynamic white and color off: Select dynamic white tone with “Kelvin grade” bar and color will be switched off.
Led Strip-controller connection
Connection drawing
- 5 in 1 driver LENNY-DRV-LS2 / LENNY-DRV-WL5
“Switch” button can be used to indicate which type of product is being
managed. To do so, press the “Switch” or “SET” button with a short touch until
color from “indicator light” is required one.
2 in 1 driver LENNY-DRV-WL2P
LENNY-TRIAC1 Push button control
Functioning
- Short press: Switches the connected device ON/OFF.
- Long press (press and hold): increases or decreases the intensity of the light.
Connection
The maximum number of TRIACs is 25 pieces and maximum wiring distance from the
push button is 20m. To control everything with a single push button, LENNY-
TRIACs must be connected in cascade according to the connection diagram.
List of LENNY-DRV-LS2 modes and functions for RGB / RGBW / RGBWW
| Number | Dynamic mode | Brightness / Saturation / Speed |
|---|---|---|
| 1 | Mardi Gras | **** |
Adjustable
2| Automatic colors changing
3| Sam
4| Gemma
5| Twlight
6| American
7| Super super Tuesday
8| Party
9| Splash colors
List of LENNY-DRV-WL5 modes and functions for RGB / RGBW / RGBWW
System linking and unlinking
Note: The light only works after the controller is paired with one or more receivers.
Linking. Place Remote controller close to the desired driver to be
paired. Before starting linking process, configure receiver according to the
type of LED strip. Refer to “wiring diagram” section (previous point) from the
manual.
- If light does not flash slowly, the bonding is not done. Repeat the process until this occurs.
-
Switch off power supply and after 10 seconds, switch it on again.
Note: For LENNY-DRV-WL2P or LENNY-TRIAC1, press the SET button once to enter pairing mode. -
Press ON button on the remote control 3 times within a maximum period of 3 sec.
-
The light will flash 3 times slowly to indicate successful pairing.
Unlinking
- If light does not flash quickly, the bonding is not done. Repeat the process until this occurs.
-
Switch off power supply and after 10 seconds, switch it on again.
Note: For LENNY-DRV-WL2P or LENNY-TRIAC1, press the SET button once to enter pairing mode. -
Press ON button on the remote control 5 times within a maximum period of 3 sec.
-
The light will flash 10 times quickly to indicate that unlinking is successful.
Attention
- Please check if input voltage is compatible with voltage supported by the driver. Pay special attention not to cross positive and negative poles. Reversed connection will damage the controller.
- Do not connect the cables while the power supply is on. Turn it on when you are sure of connections are correct and there is no short circuit is possible.
- Avoid placing driver controller in areas influenced by electromagnetic fields or close to devices that produce electromagnetic fields. Also, do not place driver controller in areas shielded by metal surfaces or where metal surfaces come between the control and the controller. This would affect operating distance effectiveness.
Device auto-sync
Different receiver drivers can be connected to operate with the same remote controller and operate in the same modes.
. Notes
- Self emitting indication.
- Remote driver controllers can be paired with the same remote controller within a maximum range of 30 meters. (possible where as free or semi-free spaces and without too many obstacles or walls).1. : Self emitting indication.
Auto-transmitting function
A single remote controller may transmit control signals in succession to
other driver controllers provided if maximum coverage distance of 30m is
respected between them.
Battery installation – LENNY-MD-086
- Open rear control unit cover.
- Insert batteries correctly and close the cover.
Installation diagram – LENNY-TRIAC1
Mobile phone pairing
Download and install the application on your mobile phone:
- Via QRl code
- Searching the Play Store for “MiBoxer”.
Note:
Also compatible with the application: SMART LIFE
To link our installation with our mobile phone, we will need one of these drivers:
- LENNY-DRV-WL5
- LENNY-DRV-WL2P
- LENNY-DRV-LS2 + LENNY-WIFOX1
- LENNY-TRIAC1 + LENNY-WIFOX1
Register in MiBoxer:
We will receive an e-mail with a registration verification code, which we will
have to enter in the application to finish registering account. In order to
use the application, we must activate GPS on our mobile phone (either Android
or Apple). Once on the main screen and our session started, we must add the
device. To do this:
Select device model:
For model LENNY-DRV-WL5:
Click on “Smart Strip Controller (WL5)”.
For model LENNY-DRV-WL2P:
Click on “LED controller (FUT035W-FUT039W)”.
For model LENNY-DRV-LS2 or model LENNY-TRIAC1:
Click on “2.4GHz Gateway (WL-Box1)”.
For model LENNY-DRV-WL5
Disconnect power supply from LENNY-DRV-WL5 for 10 sec. After 10 seconds, power
the controller and within the first three seconds, press and hold “SET” button
on the receiver until LED on the receiver flashes.
For models LENNY-DRV-WL2P / LENNY-DRV-LS2 / LENNY-TRIAC1
Press SET button on device or on WIFI gateway for 3 seconds to activate
WIFI signal. In both cases, on the phone screen, click on “Ensure pilot lamp
blinking”.
-
Enter network name and password.
Attention: only 2.4GHz network is supported (no 5G) and click on “Start configuration”. -
A countdown will appear and once paired, it will indicate that pairing has been successful.
-
Our device will appear in the list of paired devices.
Wether we have to use the WIFI gateway (LENNY-WIFOX1):
We must link the driver to be controlled via the APP. To do this, click on
2.4GHz gateway. First we must choose whether we are going to configure one or
more zones. In this case, as it is a zone, we enter the “change” section and
select FUT088/B0.
- On the screen of our mobile phone we will see image as follows:
- Click on “Link/Unlink”.
- Click on “link” to link and on “unlink” to unlink.
- Remove the power supply to controller for 10 seconds.
- After 10 seconds, power the controller and in the first
- 3 seconds, click on the mobile screen on “link” or “unlink”.
- The light will flash three times and confirm correct linking.
- In the case of unlink, light will flash 10 times for confirmation.
- The application allows us to create groups with different receivers. This will allow us to control several receivers at the same time: turn ON / OFF / change the color, etc.
- Once we have linked our receiver we can change our device name. This is interesting if we are going to control it with Alexa, Google Assistant or Google Home. To do so, we press and hold name of the device on the screen and move it to the left. We will see an “edit” and a “delete”. Click on “Edit”, change the name and “Ok”.
ALEXA linking
To control system with Alexa, a wifi gateway is required, either built into
receiver or using LENNY-WIFOX1 gateway. Install Alexa app and log in using
your account. We need to install Mi-Light Smart skill. To do so:
Once reached step as above, Alexa will detect our receiver automatically and
we will be able to change its name, include it in a group or control it by
voice. If receiver is not detected automatically , we can push “detect
devices” via Alexa app function. Now you can work with standard ALEXA managing
.
We can rename device to be able to control that device only instead the whole group, command Alexa to turn off/on the device, etc.
GOOGLE HOME linking
To control system with Google Home, a wifi gateway is required, either built
into the receiver or using LENNY-WIFOX1 gateway. Install Google Home app and
log in with your Google account. If you have not yet configured your home, you
can do this now or later. We need to install Mi-Light Smart skill. To do this
:
Once we have reached this point, the linking is done.
To control system with Google Assistant, a wifi gateway is required, either
built into the receiver or using LENNY-WIFOX1 gateway. And Install Google
Assistant application via PlayStore on your phone:
We must configure it to recognize your voice. Then enter “settings” in the application and click on “Voice Match”. The application will ask you to repeat two phrases several times. Once this is done, we will be able to “call” our device using “Ok Google”. For example, “Ok Google turn on Fullwat” and LED strips connected to Fullwat receiver will light up properly.
Compatibility table
| ****
Single color
| ****
CCT
| ****
RGB
| ****
RGBW
| ****
RGBWW
| “Mobile app Alexa
Google Home”
| ****
Zones
---|---|---|---|---|---|---|---
LENNY-DRV-LS2 LENNY-DRV-LS2S
5-in-1 standard receiver
| LENNY-MD-085| LENNY-MD-085| | | | LENNY-WIFOX1
gateway is required
| 1
LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| 1
LENNY-MD-087| | | | | 1
LENNY-MD-088| LENNY-MD-088| LENNY-MD-088| LENNY-MD-088| LENNY-MD-088| 1
LENNY-PAN-B0| LENNY-PAN-B0| LENNY-PAN-B0| LENNY-PAN-B0| LENNY-PAN-B0| 1
LENNY-PAN-K1| LENNY-PAN-K1| | | | 1
LENNY-MD-007| LENNY-MD-007| | | | 4
LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| 4
LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN-B4| 4
LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| 8
LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-B8| 8
LENNY-DRV-WL5
5 in 1 wifi receiver
| LENNY-MD-085| LENNY-MD-085| | | | included| 1
LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| LENNY-MD-086| 1
LENNY-MD-087| | | | | 1
LENNY-MD-088| LENNY-MD-088| LENNY-MD-088| LENNY-MD-088| LENNY-MD-088| 1
LENNY-PAN-B0| LENNY-PAN-B0| LENNY-PAN-B0| LENNY-PAN-B0| LENNY-PAN-B0| 1
LENNY-PAN-K1| LENNY-PAN-K1| | | | 1
LENNY-MD-007| LENNY-MD-007| | | | 4
LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| LENNY-MD-092| 4
LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN-B4| LENNY-PAN-B4| 4
LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| LENNY-MD-089| 8
LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-B8| LENNY-PAN-B8| 8
LENNY-DRV-WL2P
2 in 1 receiver with wifi and push button
| LENNY-MD-085| LENNY-MD-085| | | | included| 1
LENNY-MD-086| LENNY-MD-086| | | | 1
LENNY-MD-087| | | | | 1
LENNY-MD-088| LENNY-MD-088| | | | 1
LENNY-PAN-B0| LENNY-PAN-B0| | | | 1
LENNY-PAN-K1| LENNY-PAN-K1| | | | 1
LENNY-MD-007| LENNY-MD-007| | | | 4
LENNY-MD-092| LENNY-MD-092| | | | 4
LENNY-PAN-B4| LENNY-PAN-B4| | | | 4
LENNY-MD-089| LENNY-MD-089| | | | 8
LENNY-PAN-B8| LENNY-PAN-B8| | | | 8
LENNY-TRIAC1
Driver TRIAC
| LENNY-MD-085| | | | | LENNY-WIFOX1
gateway is required
| 1
LENNY-MD-086| | | | | 1
LENNY-MD-087| | | | | 1
LENNY-MD-088| | | | | 1
LENNY-PAN-B0| | | | | 1
LENNY-PAN-K1| | | | | 1
LENNY-MD-007| | | | | 4
LENNY-MD-092| | | | | 4
LENNY-PAN-B4| | | | | 4
LENNY-MD-089| | | | | 8
LENNY-PAN-B8| | | | | 8
Table of controls by zones
Documents / Resources
|
fullwat LENNY-MD-086 Smart LED Control
System
[pdf] Owner's Manual
LENNY-MD-086 Smart LED Control System, LENNY-MD-086, Smart LED Control System,
LED Control System, Control System, System
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>