steinel 058661 Outdoor Llluminator Smart Light Instruction Manual

: June 15, 2024
: STEINEL

Table of Contents

steinel 058661 Outdoor Llluminator Smart Light Instruction Manual
About this document
General safety precautions
Way/Garden
Installation
Function
Light tilting/swiveling range / Changing lamp
Maintenance
Disposal
Declaration of Conformity
Manufacturer’s Warranty
Technical specifications
Troubleshooting
Read More About This Manual & Download PDF
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

steinel 058661 Outdoor Llluminator Smart Light Instruction Manual

Spot Way, Spot Way NightAuto, Spot Way SC, Spot Garden, Spot Garden NightAuto, Spot Garden SC

About this document

Please read it carefully and keep it in a safe place.
Under copyright.
Reproduction either in whole or in part only with our consent.
Subject to change in the interest of technical progress.
- All product dimensions in mm.

Symbols
Hazard warning!
**** Reference to other information in the document.

General safety precautions

Disconnect the power supply before attempting any work on the unit.

Only use genuine replacement parts.
Repairs may only be made by specialist workshops.
Not suitable for use with halogen lamps.

Way/Garden

Proper use
– Outdoor LED light for mounting on the ground.
– For connection to an IP44 power socket.
Spot Way NightAuto / Spot Garden NightAuto
– The sensor-switched LED light contains a light-level sensor.
Spot Way SC / Spot Garden SC
– The sensor-switched LED light contains an infrared motion detector and can only be adjusted via Bluetooth and app.

Non-intended use
– The LED light cannot be dimmed.
Not dimmable

Way spot package contents (Fig. 3.1)
– Light including pillar, ground plate, and power cord cable with mains plug
– Three screws
– Three ground plugs
Garden spot package contents (Fig. 3.2)
– Light including power cord cable with mains plug
– Ground spike
– Two screws
Spot Way product dimensions (Fig. 3.3)
Spot Garden product dimensions (Fig. 3.4)
Product parts (Fig. 3.5 – 3.10)
A Light enclosure
B Motion sensor (Spot Way / Spot Garden SC only)
C Light-level sensor (Spot Way / Garden NightAuto only)
D Twilight setting (Spot Way / Garden NightAuto only)
E Pillar with ground plate (Spot Way only)
F Ground spike (Spot Garden only)
G Mains power cord with plug
Detection zone for Spot Way / Spot Garden SC (Fig. 3.11 – 3.16)
Luminous intensity distribution (Fig. 3.17)

Installation

Check all components for damage.
Do not use the product if it is damaged.
This light’s external, flexible cord cannot be replaced.
If the cord gets damaged, the entire light must be replaced.
When installing the light, make sure the installation site is not subject to vibration.
Select an appropriate mounting location, taking the reach and motion detection into consideration.

Spot Way / Spot Garden SC only:
The most reliable way to detect movement is given by mounting the light to point across the direction in which people walk and by making sure no obstacles (e.g. trees, walls, etc.) interrupt the line of sensor vision.

Way mounting procedure

Fit floodlight head on the pillar and turn until it clicks into place. (Fig. 4.1)
Mark drill holes for the ground plate. (Fig. 4.2)
Drill holes and fit ground plugs. (Fig. 4.3)
Procedure for mounting the light on the ground. (Fig. 4.4)
Connect plug. (Fig. 4.5)
Make settings. ➜ „5. Function“

Mounting procedure for Garden

Attach ground spike to light. (Fig. 4.6)
Push light into the ground. (Fig. 4.7)
Connect plug. (Fig. 4.8)
Make settings. ➜ „5. Function“

Information for NightAuto version

Make sure that the light-level sensor is not covered (e.g. by leaves).

Function

Spot Way NightAuto / Spot Garden NightAuto
Factory settings
– Control dial set to = permanently ON
Twilight setting (Fig. 5.2 D)
The light’s chosen response threshold can be infinitely varied from approx. 2 to 1000 lux.
– Control dial set to = permanently ON
– Control dial set to = night-time operation (approx. 2 lux)
For performing the functional test in daylight, the control dial must be set to .

Spot Way SC / Spot Garden SC
Factory settings
– Twilight setting: 2000 lux
– Time setting: 5 seconds
Smart Remote app
To configure the light via smartphone or tablet, you must download the STEINEL Smart Remote app from your app store. You will need a Bluetooth-capable smartphone or tablet.

www.steinel-professional.de/SmartRemote/Android/| www.steinel- professional.de/SmartRemote/iOS/
---|---

The following functions can be set via the Smart Remote app:

Time setting
Twilight setting
ON and OFF times
Automatic/manual control, depending on the situation
Interconnection
Grouping
Naming groups and lights

Note:
After the light switches OFF, it takes approx. 1 second before it is able to start detecting movement again. The light will only switch ON in response to movement once this period has elapsed.
The Spot SC has an internal clock for time-based activation and deactivation. This automatically synchronizes with the clock of the connected smartphone via the Smart Remote app each time a Bluetooth connection is established. To ensure correct function following an interruption in the light’s power supply, it must be re-connected via the Smart Remote app. The internal clock is re- synchronized with the smartphone clock.

Light tilting/swiveling range / Changing lamp

Light tilting/swiveling range
– Way (Fig. 6.1)
– Garden (Fig. 6.2)
Changing lamp

Undo the glass cover and detach it from the light enclosure. (Fig. 6.3)
Disconnect and remove the lamp . (Fig. 6.4)
Insert a new lamp and twist to engage. (Fig. 6.5)
Fit glass cover and twist to engage. (Fig. 6.6)

Important:
Only use GU10 LED lamp with wattage up to 9 W.
Note:

On changing a lamp, make sure that the seal and sealing surface are not soiled or damaged.

Maintenance

The product requires no maintenance.
The light can be cleaned with a damp cloth (without detergents) if dirty.
Important note: the control gear cannot be replaced.

Disposal

Electrical and electronic equipment, accessories, and packaging must be recycled in an environmentally compatible manner.
Do not dispose of electrical and electronic equipment as domestic waste.
EU countries only:
Under the current European Directive on Waste Electrical and Electronic Equipment and its implementation in national law, electrical and electronic equipment no longer suitable for use must be collected separately and recycled in an environmentally compatible manner.

Declaration of Conformity

Hereby, STEINEL Vertrieb GmbH declares that the radio equipment type Spot Way SC /Spot Garden SC is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.steinel.de

Manufacturer’s Warranty

This Steinel product has been manufactured with the utmost care, tested for proper operation and safety, and then subjected to random sample inspection. Steinel guarantees that it is in perfect condition and in proper working order. The warranty period is 36 months and starts on the date of sale to the consumer. We will remedy defects caused by material flaws or manufacturing faults. The warranty will be met by repair or replacement of defective parts at our own discretion. The warranty shall not cover damage to wear parts, damage, or defects caused by improper treatment or maintenance. Further consequential damage to other objects shall be excluded. Claims under the warranty will only be accepted if the unit is sent fully assembled and well- packed with a brief description of the fault, a receipt or invoice ( date of purchase and dealer’s stamp ) to the appropriate Service Centre.

Repair service:
If defects occur outside the warranty period or are not covered by the warranty, ask your nearest service station for the possibility of repair.
3 YEAR
MANUFACTURER’S
WARRANTY

Technical specifications

Dimensions (W × D × H) (W × D × H)| Spot Way: 140 × 226 × 572 mm Spot Garden: 69 × 118 × 369 mm
---|---
Cord length| 2,500 mm
Supply voltage| 220 – 240 V, 50/60 Hz
Power consumption (Pon) Light | Spot Way / Garden: 6.70 W Spot Way / Garden NightAuto: 7.86 W Spot Way / Garden SC: 7.90 W
Luminous flux/brightness Light | Spot Way / Garden: 512 lm; 76.40 lm/W Spot Way / Garden NightAuto: 512 lm; 65.10 lm/W Spot Way / Garden SC: 512 lm; 64.80 lm/W
Luminous flux Lamp| 620 lm 92.5 lm/W
Power consumption Lamp| 6.7 W
Standby (light)| Spot Way / Garden NightAuto: 0.20 W Spot Way / Garden SC: 0.42 W
Standby (network) (Pnet)| Spot Way / Garden SC: 0.42 W
Color temperature | 3,000 K (warm white)
Color rendering index | Ra >80
Average rated life expectancy | L70B50 at 25°C: >20,000 hours.
Colour consistency SDCM | 6
Sensor technology| Passive infrared (Spot Way / Garden SC only)
Detection zone
• Angle of coverage
• Angle of aperture| (Spot Way / Garden SC only) 90° 90°
Reach| max. 10 m (Spot Way / Garden SC only)
Time setting| 5 s – 60 min (Spot Way / Garden SC only)
Twilight setting| 2 – 1,000 lux (Spot Way / Garden NightAuto only) 2 – 2,000 lux (Spot Way / Garden SC only)
IP rating| IP44
Protection class| I
Ambient temperature| -20 to +40°C
Bluetooth frequency| 2.4 – 2.48 GHz (Spot Way / Garden SC only)
Bluetooth transmitter power (Pnet)| 5 dBm / 0.60 mW (nur Spot Way / Garden SC)

for LED lamp provided This product contains an energy efficiency class „F“ light source.

Troubleshooting

Malfunction	Cause	Remedy
LED light does not switch ON	■ Fuse has tripped, not switched ON, break in

the wiring
■ Short circuit
■ Lamp faulty| ■ Activate, change a fuse, turn ON the mains switch, and check the wiring with a voltage tester
■ Check connections
■ Change lamp
NightAuto LED light does not switch ON| ■ Twilight setting in night-time mode during daytime operation
■ Mains switch OFF
■ Fuse has tripped
■ Detection zone not correctly adjusted| ■ Reset
■ Switch ON
■ Activate, change a fuse, check connection if necessary
■ Readjust
NightAuto LED light does not switch OFF| ■ The twilight setting is set to permanently ON during night-time operation
■ Continued movement within the detection zone
■ Light-level sensor is covered (e.g. by leaves).| ■ Reset
■ Check zone and readjust if necessary or apply shroud
■ Remove shrouds from the light-level sensor
SC LED light keeps switching ON/OFF| ■ Animals moving in the detection zone| ■ Tilt sensor higher or fit shrouds to target sensor; adjust detection zone or fit shrouds
Malfunction| Cause| Remedy
---|---|---
SC LED light switches ON
when it should not| ■ Wind is moving trees and bushes in the detection zone
■ Cars in the street are being detected
■ Sudden temperature changes due to weather (wind, rain, snow) or air expelled from fans or open windows
■ Sensor-switched LED light is swaying (moving) due to gusts of wind or heavy rain| ■ Change detection zone
■ Change detection zone
■ Adjust detection zone or install in a different place
■ Mount sensor-switched LED light on a firm surface