STEEL GREEN SG36 Independent Sprayer Instruction Manual

June 13, 2024
STEEL GREEN

STEEL GREEN SG36 Independent Sprayer

STEEL GREEN SG36 Independent Sprayer

Models: SG36, SG42

7 GAL. INDEPENDENT SPRAYER EXPLODED VIEW \ RIGHT SIDE

PARTS LIST


ITEM| QTY| PART NUMBER| DESCRIPTION
1| 1| S54000| PUMP, SHURFLO
2| 1| S54120| HEAT SINKI SPRAY PUMP
3| 2| S54103| PUMP FIIBNG, BARB, ELBOW, 1/ 2 X 1/ 2
4| 2| S51242| BULKHEAD FITTING, TANK
5| 1| S51270| SPRAY FILTER
6| 1| S52063| 3/4 X 3/4 ST
7| 1| S52028| ELBOW. 3 / 4 X 1/2 BARB
8| 1| 551283| VALV, E THROTTLING
9| 1| S52000| TEE. PIPE. 3/4 WITH GAUGE PORT
10| 1| M10007-R-IND| TANKI 7 GALLON
11| 1| S51243| CAP, TANK
12| 4| CB-51634| CARRIAGE BOLT, SS – 5/16-18 x 3/4
13| 4| HFNCS-516S| HEX FLANGE NUT. SS – 5/16-18
14| 4| TRPC-141S| PHILLIPS SCREW, SS – 1/ 4-20 x 1
15| 4| SSNNC-14| NYLOCK, SS – 1/ 4-20
16| 4| HFSSC-3875| HEX BOLT. 3/8 X 3/4
17| 1| 551234-D| PRESSURE GAUGE, 60 PSI
18| 1| R21-113| ANTI VORTEX PLATE
19| 1| 552041| 90 ELBOW, 3/4 MNPT X 3/4 FNPT
20| 1| S53019| HOSE,COIL
21| 1| 551260| HANDLE, SPRAY
22| 1| S51261| NOZZLE, SPRAY
23| 4| MS4| HOSE CLAMP. 3/ 8
24| 1| S52064| 3/4 X 1 / 2 REDUCER
25| 1| 552050| 1/2 X 1 /4
26| 1| S52025| 1/ 2 MPT X 1/2 BARB
27| 1| R22-164-R| TANK SUPPORT.7 GAL., RIGHT SG36

7 GAL. INDEPENDENT SPRAYER EXPLODED VIEW \\ RIGHT SIDE

7 GAL. INDEPENDENT SPRAYER EXPLODED VIEW \ LEFT SIDE

PARTS LIST


ITEM| QTY| PART NUMBER| DESCRIPTION
1| 1| S54000| PUMP, SHURFLO
2| 1| S54120| HEAT SINK, SPRAY PUMP
3| 2| S54103| PUMP FILLING, BARB, ELBOW, 1/ 2 X 1 / 2
4| 2| S51242| BULKHEAD FI I IING, TANK
5| 1| S51270| SPRAY FILTER
6| 1| S52063| 3/ 4 X 3/ 4 ST
7| 1| S52028| ELBOW, 3/ 4 X 1/2 BARB
8| 1| S51283| VALVE, THROTTLING
9| 1| S52000| TEE. PIPE. 3/4 WITH GAUGE PORT
10| 1| M10007-R-IND 36|
11| 1| S52050| 1/2 X 1 / 4
12| 1| S51243| CAP, TANK
13| 4| CB-5161S5| CARRIAGE BOLT, SS – 5/16-18 x 1
14| 4| HFNCS-516S| HEX FLANGE NUT, SS – 5/16-18
15| 4| TRPC-141S| PHILLIPS SCREW, SS – 1/4- 20 x 1
16| 4| SSNNC-14| NYLOC,KSS – 1/4-20
17| 4| HFSSC-3875| HEX BOLT, 3/8 X 3/4
18| 1| S51234-D| PRESSURE GAUGE, 60 PSI
19| 1| R21-113| ANTI VORTEX PLATE
20| 1| SS2041| 90 ELBOW, 3/4 MNPT X 3/4 FNPT
21| 1| S53019| HOSE. COIL
22| 1| S51260| HANDLE, SPRAY
23| 1| S51261| NOZZLE, SPRAY
24| 4| MS4| HOSE CLAMP. 3/8
25| 1| S52064| 3/4 X 1/ 2 REDUCER
26| 1| S52025| 1/ 2 MPT X 1/ 2 BARB
27| 1| S55003| 1/ 2 HOSE
28| 1| R22-164| TANK SUPPORT.7 GAL., LEFT SG36

7 GAL. INDEPENDENT SPRAYER EXPLODED VIEW \\ LEFT SIDE

7 GAL. INDEPENDENT HOSE ROUTING

7 GAL. INDEPENDENT HOSE ROUTING
7 GAL. INDEPENDENT HOSE ROUTING

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

STEP ONE: Disconnect the battery, ground first and then power wire.

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

STEP TWO : Remove existing storage container and support bracket from the frame.

NOTE: Instructions are the same for the right and left side.

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

STEP THREE: Install the independent sprayer to the frame as shown.

NOTE: Instructions are the same for the right and left side.

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

STEP FOUR: Connect the “pump” wiring harness to the pump plug and route the harness between the tank and upright.

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

STEP FIVE: Route the “pump” wiring harness along the frame and upright to the control panel.

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

STEP SIX: Remove the plastic cap from “Aux 1” in the panel and route the switch connector of the “pump” wiring harness through the hole in the panel.

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

STEP SEVEN: Connect the “pump” wiring harness to the “20A” side of the rocker switch.

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

STEP EIGHT: Connect the ground wire from the “pump” wiring harness to the up right cross member.

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

STEP NINE: Connect the “pump power” wiring harness to the other side of the rocker switch.

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

STEP TEN: Install the rocker switch in the control panel and route the “pump power” wiring harness down the up right, along the frame to the battery.

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

STEP ELEVEN: Reconnect the battery power wire first along with the pump power wire from the wiring harness, and then reconnect the ground wire.

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

STEP TWELVE: Once both harnesses are routed and connected, securely fasten them to the frame and existing harnesses in the up right with zip ties.

7 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS

MANUAL PART NO.| MANUAL REV.| DESCRIPTION| KIT PART NO.
---|---|---|---
SGM-010| B| SG36-42 7 GALLON INDEPENDENT SPRAYER| P10031

Customer Support

Steel Green Mfg.
824 S State Road 39
Lebanon, IN 46052
(765)-481-2890
www.steelgreenmfg.com

LogoLogo

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

STEEL GREEN User Manuals

Related Manuals