STEEL GREEN MANUFACTURING SG36 Zero Turn Sprayer Instruction Manual

Table of Contents

STEEL-GREEN-MANUFACTURING-SG36-Zero-Turn-Sprayer-
PRODUCT

Specifications

Installation Guide

Disconnect hoses from the hopper, ensuring to hold them up to prevent oil spillage.
Ensure the female quick connect is on the left side (blue) and the male quick connect is on the right side (red).
Disconnect cables from the dash after making sure the hopper is empty.
Remove the six bolts holding the hopper assembly to the frame and lift the assembly.
Attach the valve assembly to the corner of the dash panel.
Follow the additional instructions provided in the manual for attaching suction lines and other components.

Maintenance

Regularly check for leaks, ensure proper connections, and clean the tank after each use to prevent clogging.

Storage

Store the tank in a cool, dry place away from direct sunlight when not in use to prolong its lifespan.

FAQ

Q: How do I ensure the proper connection of hoses during installation?

A: Make sure to match the female quick connect (blue) with the left side and the male quick connect (red) with the right side as indicated in the manual.

Q: What should I do if I encounter leaks?

A: Check for loose connections, worn-out seals, or cracks in the tank. Tighten connections or replace parts as needed.

Q: Can I use this tank for chemicals other than oil?

A: It is recommended to only use the tank for its designated purpose to avoid contamination and damage.

STEEL-GREEN-MANUFACTURING-SG36-Zero-Turn-Sprayer-FIG-1

QUICK CONNECT KIT – K10029

STEP 1:

Disconnect the battery, ground first, and then power wire.
Remove the battery from the battery box.
STEP 2: Disconnect the hoses from the hopper.
NOTE: Hold the hoses up to prevent oil spillage
STEP 3: QUICK CONNECT INSTALL
NOTE: Be sure the hopper is drained before starting the following steps.
Remove the grate.
Disconnect the hopper motor hoses from the bulkhead fittings.
Remove the bulkhead fittings from the hopper.
Attach the quick couplers provided with the kit to the hopper.
NOTE: Be sure the FEMALE quick connect is on the LEFT SIDE (SHOWN BLUE) and the MALE quick connect is on the RIGHT SIDE (SHOWN RED).
Reconnect the hopper motor hoses.
Reinstall the grate.
Connect the FEMALE end provided with the kit, to the end of the RIGHT SIDE hose.
Connect the MALE end provided with the kit, to the end of the LEFT SIDE hose.
Once the QDs have been attached, connect the hoses to create a hydraulic loop.
STEP 4: Disconnect the cables from the dash.
NOTE: Be sure the hopper is empty before proceeding.
STEP 5: Remove the six bolts that hold the hopper as-sembly to the frame and lift the hopper assembly from the frame.
STEP 6: Set the 20-gallon tank assembly on the frame.
Attach it to the frame with the six bolts.
STEP 7: Attach the valve assembly to the corner of the dash panel.
VALVE ASSEMBLY
VALVE ASSEMBLY W/FOAM MARKER

NOTE:

Before beginning step 8, BE SURE there is no pressure on the lines and fluid is drained.
Parts not shown for clarity.
STEP 8: Remove the knee pad to access the return & suction lines.
Carefully cut and install the “tee” fittings in the “suction” and “return” lines as shown (blue arrows). Securely fasten with 3/4 hose clamps.
STEP 9: Cut and install a 3/4” suction hose, connecting one end to the suction fitting on the top valve and the other end to the “tee” fitting in the suction line.
Cut and install a 3/4” return hose, connecting one end to the return fitting on the bottom valve and the other end to the “tee” fitting in the return line.
Securely fasten each end with a 3/4” hose clamp.
STEP 10: Connect the “quick disconnect” hos-es from the tank to the valves.
STEP 11: Set the battery in the battery box.
Reattach the battery cables, power cables, and wires first followed by the ground wire.
Attach the battery box cover and bungee strap.
MADE IN THE USA
Steel Green Mfg.
824 S State Road 39 Lebanon, IN 46052
(765)-481-2890
www.steelgreenmfg.com