HOOVER HDG6DCK3BWIFI Wall Cooker Hood User Manual

HOOVER HDG6DCK3BWIFI Wall Cooker Hood

Specifications

• Fuse: 3 Amps
• Installation Accessories: Casing, Upper Chimney, Lower Chimney, Lower chimney bracket, Upper chimney bracket, Hanging Board, rawl plugs, Screws
• Installation Method: Wall mounting
• Air Ventilation: 150mm diameter extraction duct
• Distance above Cooking Plane : 65-75cm

Product Usage Instructions

Installation (Vent Outside)

1. Turn off and unplug the unit before installation.
2. Place the cooker hood 65-75cm above the cooking plane.
3. Drill 3 x 8mm holes for the bracket and secure it to the wall.
4. If inclined panel model, drill extra holes and fixings before installation.
5. Hang the cooker hood onto the wall bracket hook.
6. Attach the one-way valve to the air outlet and connect the exhaust pipe.

INTRODUCTION

Thank you for choosing this cooker hood.
This instruction manual is designed to provide you with all required instructions related to the installation, use, and maintenance of the appliance. To operate the unit correctly and safely, please read this instruction manual carefully before installation and usage.
The cooker hood uses high-quality materials and is made with a streamlined design. Equipped with a large power electric motor and centrifugal fan, it also provides strong suction power, low noise operation, a non-stick grease filter, and easy assembly installation.
Hereby, Candy Hoover Group Srl declares that the radio equipment is in compliance with Directive 2014/53/EU and with the relevant Statutory Requirements (for the UKCA market).
The full text of the declaration of conformity is available at the following internet address: www.candy-group.com.

SAFETY PRECAUTION

• Never let the children operate the machine.
• The cooker hood is for home use only, not suitable for barbecues, roast shops, and other commercial purposes.
• The cooker hood and its filter should be cleaned regularly to keep in good working condition.
• Clean the cooker hood according to the instruction manual and keep the unit from danger of burning.
• Forbid the direct baking from the gas cooker.
• Please keep the kitchen room a good convection.
• Before connecting this appliance check that the power supply cord is not damaged. A damaged supply cord must be replaced by qualified service personnel only.
• There shall be adequate ventilation in the room when the range hood is used at the same time as appliances burning gas or other fuels;
• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels;
• Regulations concerning the discharge of air have to be fulfilled.
• This appliance is not intended for use by persons(including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not flambé under the range hood.

CAUTION: Accessible parts may become hot when used with cooking appliance

• These shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels(not applicable to appliances that only discharge the air back into the room);
• the details concerning the method and frequency of cleaning.
• there is a fire risk if cleaning is not carried out according to the instructions; – do not flame under the range hood;
• CAUTION: Accessible parts may become hot when used with cooking appliances.

Electrical Shock Hazard

• Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably qualified engineer.
• Failure to follow these instructions can result in death, fire, or electrical shock.

The lamp used in this product is not suitable for use in the lighting of a room.
The purpose of this lamp is to provide illumination for using the product.

Electrical Installation

All installation must be carried out by a competent person or qualified electrician. Before connecting the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate.

Direct Connection

• The appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3mm between the contacts.
• The installer must ensure that the correct electrical connection has been made and that it complies with the wiring diagram.
• The cable must not be bent or compressed.
• Regularly check the power plug and power cord for damage. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

WARNING: This is a Class I appliance and MUST be earthed This appliance is supplied with a 3-core mains cable colored as follows:

• Brown = L or Live
• Blue = N or Neutral
• Green and Yellow = E or Earth

Standard Installation Accessories List

INSTALLATION （wall mounting）
If you have an outlet to the outside, your cooker hood can be connected as in the below picture using an extraction duct (enamel, aluminum, flexible pipe, or inflammable material with an interior diameter of 150mm)

1. Before installation, turn the unit off and unplug it from the outlet.

2. The cooker hood should be placed at a distance of 65~75cm above the cooking plane for the best effect.

3. Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten the bracket onto the wall with the screws provided. For the inclined panel Model
   needs to drill 2x8mm extra holes & fixing screws & screw plugs before installation. Voor schuine modellen

4. Leave up the cooker hood and hang onto the wall bracket hook.

5. Fix the one-way valve to the air outlet of the cooker hood. Then, attach the exhaust pipe onto the one-way valve as shown below.

   • Place the glass in the appropriate position on the top of the cooker hood.
   • Fix with 4 screws and washer. To avoid the glass cracking, please do not tighten the screws too strongly.
   • But the inner chimney into the otouterter chimney. Then pulling out the inner chimney upwards. Adjust to reach the height required.
   • Sliding the chimney to adjust the chimney height. When the height you required is reached, then hang the fixing hole to the fixing screws as shown in the below pictures.
   • Drill 2 x 8mm holes to accommodate the plate II. Screw and tighten the plate II onto the wall with 2 screws provided.
   • Assemble the chimney onto the unit and fix it with 2 screws.

Standard Installation Accessories List

INSTALLATION（AIR DEFLECTOR FOR PYRAMID & SLANT MODELS):
Air deflector is mentioned as included and not optional.

1. Fix the bracket to the T-shaped plastic outlet with 2pcs ST3.5x12mm screws provided as shown below:
2. Drill 2 holes on the wall to accommodate the wall plugs, then screw, and tighten the bracket onto the wall with 2pcs ST4x30mm screws provided.
3. Attach the exhaust pipe onto the air outlet of the cooker hood as shown below:
4. Install the chimney to the unit and fix it.
   • “Please kindly note: T-shaped plastic outlet and v-flaps can not be used at the same time. You can use them in two ways: 1)Addv-flaponexistingo utlet; 2) Use T-shaped plastic outlet, no add v-flap.”
   • “ Note: The product is provided with a v-flap accessory. This accessory is not mandatory for installation, operation, and use of the product.”

INSTALLATION (VENT INSIDE)

If you do not have an outlet to the outside, an exhaust pipe is not required and the installation is similar to the one shown in the section “INSTALLATION (VENT OUTSIDE)”.

An activated carbon filter can be used to trap odors.
To install the activated carbon filter, the grease filter should be detached first. Press the lock and pull it downward.

Plug the activated carbon filter into the unit and turn it in a clockwise direction. Repeat the same on the other side.

NOTE:

• Make sure the filter is securely locked. Otherwise, it would loosen and cause danger.
• When the activated carbon filter is attached, the suction power will be lower

DESCRIPTION OF COMPONENTS

OPERATION

Timer button

1. Setting the time of the day
   When the hood is in standby mode (motor not working), press the timer button to enter the time setting.
   Press the ‘Fan speed’ key to set the hour of the day and press the ‘Light ‘key to set the minute.

2. Setting the Timer
   When the hood is in operation mode, press the timer button to set the countdown.
   Press the timer button one time then the countdown will increase by one minute. The max countdown is 60 minutes.

FAN SPEED Button
Standby mode: the backlit of all buttons and LCD are off, long press the speed button or lamp button approximately at 0.5 seconds: the buzzer buzz once, the backlit of the button will light on, and the speed icon or lamp icon the LCD will light on, and the cooker hood enter into power on mode; if only the motor working, short press the “‐” button to speed 1, the cooker hood will enter into standby mode if press the “‐” button again, or only the lamp is on, short press the lamp button then enter into standby mode.

Boost Function:

1. Boost 1(speed 4):Fan speed at level 5 +TURBO
   Press the speed button to speed 4, and the fan icon on the LCD shows the motor is working and the speed icon on the LCD shows speed is working at level 5+ TURBO, the cooker hood is working at boost mode.

2. Boost 2(speed 5):Fan speed at level 6 +TURBO
   Press the speed button to speed 5, and the fan icon on the LCD shows the motor is working and the speed icon on the LCD shows speed is working at level 6 + TURBO, the cooker hood is working at boost mode.
   Note: Enter into Boost speed while the hood is in use and it will increase speed for 5 minutes, before slowing down again.

Wi‐Fi Connection
Setting the time of the day
Long press the WiFi icon and enter into connecting mode: the backlit WiFi icon keep flashing to indicate the connection is under connection, the backlit WiFi icon is light on indicating it is connected, same for standby mode; long press the WiFi icon again and the connection will be stopped;
LIGHT Button
For lighting ON & OFF.

LCD

1. The motor symbol will rotate when the motor is working;
2. Time display;
3. Timer symbol will appear when the timer is set and counting;
4. Light symbol;
5. Motor speed;
6. The turbo speed symbol will appear when the speed is highest set;
7. The alarm symbol will appear 5 seconds after the counting down of the timer is ovThe tcleaninginggingarm, appears when the total working time is up to 14 hours or the first timeitt ing after plugging.

Download hOn App
First of all, you should download the hOn APP and install on your portable device. Then enroll your hood.

NOTE

ENROLLMENT HOOVER HOOD

The image of the hood has the only purpose of presenting it. May not be perfectly representative.

1- Press the WiFi button until the icon starts blinking When the pairing is completed the WiFi icon will be on.

MAINTENANCE

Before cleaning switch the unit off and pull out the plug.

Regular Cleaning
Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemicals, abrasive material, or stiff brushes to clean the unit.

Monthly Cleaning of Grease Filter
ESSENTIAL: Clean the filter every month can prevent any risk of fire.

The filter collects grease, smoke, and dust…… so the filter is directly affecting the efficiency of the cooker hood. If not cleaned, the grease residue (potentially flammable) will saturate on the filter. Clean it with household cleaning detergent.

Annual Cleaning for Activated Carbon Filter
Apply SOLELY to a unit that is installed as a recirculation unit (not vented to the outside). This filter traps odors and must be replaced at least once a year
depending on how frequently the cooker hood is used.

Changing a light bulb
Remove the screws on the glass, take off the hood glass. Find the bulb that requires replacement, you will find it located in the light fixture which is inside the exposed section of the canopy.

Disconnect the light wiring point and remove the bulb holders and wiring from the hood. Important: It’s not possible to replace the bulbs individually, it will be necessary to obtain the bulbs, bulb holders, and wiring as a complete part. (LED light: MAX 1.5W)
Fit the replacement bulbs, bulb holders, and wiring in the same manner as the originals. Then reconnect the light wiring point.
Refit the hood glass and fasten the glass screws. Make sure the screws are fully tightened.

TROUBLESHOOTING

off the unit and repair by qualified service personnel only.
The motor is damaged.
Both the light and

fan do not work

| Halogen light bulb burn.| Replace the bulb with the correct rating.
Power cord loss.| Plug into the power supply again.

Serious Vibration of the unit

| The fan blade is damaged.| Switch of the unit and repair by qualified service personnel only.
The fan motor is not fixed tightly.| Switch off the unit and repair by qualified service personnel only.
The unit is not hung properly on the bracket.| Take down the unit and check whether the bracket is in proper

location.

Suction performance is not good| Too long distance between the unit and the cooking plane| ****

Readjust the distance to 65-75cm

Product information for networked equipment

power consumption of the product in networked standby if all wired network ports are connected and all wireless network ports are activated:| ****

2 W

How to activate the wireless network port:

| If the Hood has been enrolled with the APP, turn on the Hood to activate the wireless network port.

How to deactivate wireless network port:

| If the Hood has been enrolled with the APP, turn off the Hood to deactivate the wireless network port. If the Hood hasn’t been enrolled with the APP, the wireless network port will be deactivated even if the Hood is on.

CUSTOMER ASSISTANCE SERVICE

• If you cannot identify the cause of the operating anomaly, switch off the appliance and contact the Assistance Service.
• PRODUCT SERIAL NUMBER. Where can I find it?
• It is important for you to inform the Assistance Service of your product code and its serial number (a 16-character code that begins with the number 3); this can be found on the guarantee certificate or the data plate located on the appliance.
• It will help to avoid wasted journeys to technicians, thereby (and most significantly) saving the corresponding callout charges.

ENVIRONMENTAL PROTECTION

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

• This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE).
• By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of the product.
• The symbol on the product indicates that this product may not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out per local environmental regulations for waste disposal.
• For more detailed information about the treatment, recovery, and recycling of this product, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.

FAQ

• Q: What should I do before installing the cooker hood?
  • A: Make sure to turn off and unplug the unit before starting the installation process.
• Q: How far above the cooking plane should the cooker hood be placed?
  • A: For best effect, the cooker hood should be placed at a distance of 65-75cm above the cooking plane.
• Q: What type of ventilation system is required for installation?
  • A: The cooker hood can be connected to an extraction duct with a diameter of 150mm if venting outside.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>