RUGGED RIDGE 11548.51 Spartan Rear Bumper User Guide
- June 13, 2024
- RUGGED RIDGE
Table of Contents
RUGGED RIDGE 11548.51 Spartan Rear Bumper
Product Information
| Part Number | Product Name | Manufacturer | Phone | Fax | Website |
|---|---|---|---|---|---|
| 11548.51 | Spartan Rear Bumper, JL & JLU | Omix-ADA | |||
| 770-614-6101 | |||||
| 844-270-0593 | [www.Omix- |
ADA.com](http://www.Omix-ADA.com)
Product Components
| No. | Component Name | Quantity |
|---|---|---|
| 1 | Spartan Rear Bumper | 1 |
| 2 | D-Shackle Tab | 1 |
| 3 | Mounting Bracket – Left | 1 |
| 4 | Mounting Bracket – Right | 1 |
| 5 | M14 Bolt | 8 |
| 6 | M14 Washer | 8 |
| 7 | M14 Nut Plate | 8 |
| 8 | M12 Bolt | 4 |
| 9 | M12 Washer | 4 |
| 10 | Rubber Plug | 4 |
| 11 | Sensor Bracket | 4 |
| 12 | M6 Bolt | 8 |
| 13 | M6 Washer | 8 |
| 14 | M6 Nut | 8 |
Product Usage Instructions
- Remove the factory rear bumper and tow hook. If the vehicle is equipped with back up sensors, remove them from the bumper.
- Install the factory back up sensors (if equipped) or supplied Rubber Plug in the Spartan Rear Bumper using M6 hardware and Sensor Brackets. Make sure that the plug side faces the center of the vehicle.
- Insert the M14 Nut Plate in the passenger side frame opening and loosely install the Mounting Brackets using the supplied M14 hardware.
- Install the Bumper and D-Shackle Tabs using the supplied M12 hardware. Once the bumper is in position, fully tighten the Mounting Bracket hardware.
Components
- Spartan Rear Bumper (1)
- D-Shackle Tab (2)
- Mounting Bracket – Left (1)
- Mounting Bracket – Right (1)
Components
- M14 Bolt (8)
- M14 Washer (8)
- M14 Nut Plate (1)
- M12 Bolt (8)
- M12 Washer (8)
- Rubber Plug (4)
- Sensor Bracket (4)
- M6 Bolt (8)
- M6 Washer (8)
- M6 Nut (8)
Installation Instructions
- Remove factory rear bumper and tow hook. If vehicle is equipped with back up sensors, remove from bumper.
- Install factory back up sensors (if equipped) or supplied Rubber Plug in Spartan Rear Bumper using M6 hardware and Sensor Brackets.
- NOTICE: When installing sensors, ensure plug side faces center of vehicle.
- Insert M14 Nut Plate in passenger side frame opening and loosely install Mounting Brackets using supplied M14 hardware.
- Install Bumper and D-Shackle Tabs using supplied M12 hardware. Once bumper is in position, fully tighten Mounting Bracket hardware.
Contact
- 460 HORIZON DR. SUITE 400 SUWANEE, GA 30024
- PHONE: 770-614-6101
- FAX: 844-270-0593
- PHONE: M-F 8am – 5pm EST 1-800-449-6649
- www.Omix-ADA.com
- FOR WARRANTY OR TECH CONCERNS EMAIL: webmaster@omixsupport.com
Copyright © 2018 Omix-Ada®, Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>