RUGGED RIDGE 13201.12 Passenger Side Front Seat Adapter Instruction Manual

: October 30, 2023
: RUGGED RIDGE

Table of Contents

RUGGED RIDGE 13201.12 Passenger Side Front Seat Adapter
Product Usage Instructions:
INCLUDED COMPONENTS
INSTALLATION INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RUGGED RIDGE 13201.12 Passenger Side Front Seat Adapter

Product Information: Rugged Ridge Seat Frame

The Rugged Ridge Seat Frame is a high-quality seat frame designed to provide maximum comfort and support. It is made of durable materials that can withstand rough outdoor conditions. The seat frame is easy to install and comes with all the necessary hardware for installation.

Product Usage Instructions:

Begin by removing the old seat and seat bracket from your vehicle.
Place the new Rugged Ridge Seat Frame on the floor of your vehicle and align it with the factory bolt holes.
Securely attach the seat frame to the floor of your vehicle using the factory bolts provided.
Attach the Arm to the Plate using the Medium Bolts, Medium Nuts, and Medium Washers provided.
Attach the Wire to the seat riser and then to the Plate.
Loosely attach the Plate to the Frame using a Large Nut and Large Washer. Turn the seat riser upside down to ease the installation of the Plate to the seat riser.
Attach the U-Bracket to the seat riser using the two Allen Bolts and two Fender washers provided. Route the Arm under the U-Bracket, assuring the bend is curved up towards the back of the seat.
Once the installation is complete, attach your new seat to the Frame using the four bolts removed in Step 3. Make sure you keep the original seat bracket orientation.
Securely tighten all hardware using wrenches.
Mount your new seat into your vehicle by attaching the bracket to the floor using the factory bolts provided.
For access to the rear seat when installed, move the Arm sideways and push the seat forward in an upward motion.

IMPORTANT NOTICE:
Carefully read the instructions before attempting to install this product. Rugged Ridge is in no way responsible for any damage to the vehicle or personal injury that may occur during the installation or use of this product.

INCLUDED COMPONENTS

RUGGED RIDGE 13201.12 Passenger Side Front Seat Adapter-
FIG7

IMPORTANT NOTE: IF YOU ARE INSTALLING BOTH A PASSENGER AND A DRIVER’S SIDE SEAT, START WITH THE DRIVER’S SIDE

INSTALLATION INSTRUCTIONS

Remove the four bolts attaching your old driver’s side seat with old seat risers (seat riser pictured in Figure 2) to the vehicle’s floor. NOTE: Save the bolts for later usage.
Remove the old seat with seat riser from vehicle and place it on a working area.
Locate the four bolts that mount the seat riser to your old seat and remove these bolts.
NOTE: Save these bolts for later use.
Remove the old seat from the seat riser
Remove front retainer from seat riser by chiseling off round fasteners Figure 1).
Once the front retainer is removed, loosely mount Frame to seat riser using the included Large Bolts, Nuts and Washers (Figure 2).
Loosely attach the Arm to the Plate using the Medium Bolts, Medium Nuts and Medium Washers provided (Figure 3).
Attach the Wire to the seat riser (Figure 4).
Attach the Wire to the Plate (Figure 5).
Once the wire is attached to the plate, loosely attach the. Plate to the Frame using a Large Nut and Large Washer. Tum seat riser upside down to ease the install of the Plate to the seat riser (Figure 6).
Attach the U-Bracket to the seat riser by using the two Allen Bolts two Fender washers included (Figure 7). NOTE: Route the Arm under the U-Bracket, assuring the bend is curved up towards the back of the seat.
Once the installation of the Frame to factory bracket is complete, attach your new seat to Frame using the four bolts removed in Step 3 (Figure 8). NOTE: Make sure you keep the original seat bracket orientation.
Securely tighten all hardware using wrenches.
Mount your new seat into your vehicle by attaching the bracket to the floor using the factory bolts from Step 1.