HYUNDAI HPS-300 Power Station User Manual

HPS-300 Power Station
User Manual

For Your Safety
Read and understand this manual before use.
Keep this manual for future reference.

HPS-300/600/1100/1600

We are still constantly improving this power station, therefore, some parts of this power station may be changed in order to achieve better quality, but the main functions and operations will not be alternated and changed. Your understanding would be greatly appreciated.

SAFETY

Please pay attention to the following before using this product, otherwise, it may damage your electronic devices or cause danger. To avoid fire or electrical shock hazards,  observe all ratings on the unit and products you intend to use.

1. Rechargeable Lithium-iron-phosphate (LiFePO4) battery is equipped with this product so take particular attention on operation, storage and delivery.

2. Recharge only with the charger specified by the manufacturer. A non-specified charger may create a risk of fire.

3. Charge it in a ventilated location; do not put this product in water and do not throw or beat this product.

4. Keep this product and related accessories in a safe place, which is not accessible to children. Do not expose it to sources of ignition or other heat sources to avoid danger.

5. Avoid touching the charging/discharging socket with the metal objects. Otherwise will cause a short circuit and injured.

6. Inadequate ventilation may cause damage to the unit. Do not put anything on top of the unit.

7. Do not disassemble the appliance and do not use it when the temperature is above 40 degrees.

8. Inspect the unit for dirt, dust, or moisture on a regular basis.

9. Do not insert any objects into the output port or ventilation holes.

10. Any repair must be carried out by the manufacturer or an authorized repair agent in order to avoid danger.
    Do not attempt to replace the internal battery. It shall be done by a qualified service center.

11. Do not insert any conductors into the output port deliberately.

GENERAL DESCRIPTION

This power station is made of a rechargeable Lithium-iron-phosphate (LiFePO4) battery, inverter circuit, and battery management system (BMS). It supports AC&DC input charging by the power source.

• Scope of application
  USB Port: Smartphone, MP3 Player, Digital Camera, Tablet, E-reader, etc.
  DC 12V Output Ports: LED lamp, etc.
  DC 12V Cigarette Port: 12V appliances, etc.
  AC Output Port: Electric appliances such as Televisions, Laptops, cookers, etc.
• Electric appliances which you intend to use must be less than the device’s continuous output power.
  (HPS-300: 300W / HPS-600: 500W / HPS-1100: 1000W / HPS-1600: 1500W)

MAIN PARAMETERS

5-20V, PD 100W Max
PD 60W Max
2DC 12V Port| 12V/5A
EC5 port| DC12-14.4V
DC12.8V 10A
80A(MAX)
1DC 12V Cigarette plug| 12V/10A
Charging ways| Wall &solar charging
Charging Input| 12-30V 120W
DC MPPT DC 12-30V 200W (MAX) MPPT
(MAX)
Operation temperature| 0-45°C
Product size (LWH mm)| 250190230| 250190230| 385190230| 480190230
Weight| 6.7Kg| 8.2Kg| 14.9Kg| 19.8Kg

* List of contents

OPERATION CONTROL AND DESCRIPTION

OPERATION

1) Using a power station
a. Press the power switch (12) to turn on the power station, then the LCD indicator (13) will be launched.
b. Press AC ON/OFF (14) button to turn it on, and the AC ON character (6) will display.
c. Connect one end of the cable to the AC socket (9) and the other end of it to your electric appliances after 3 seconds from the AC function turned on.
d. Press the AC ON/OFF button (14) again to turn it off when you stop to use it, and the AC OFF character (6) will display.
e. Press DC ON/OFF button (11) to turn it on, and DC character (1) will display.
f. Connect one end of the cable to any DC port like USB-A (8), Type-C (7), DC round port (16), or car cigarette port (17), and connect the other end of the cable to your mobile phone, Laptop, Drone or other digital electronic equipment.
g. Press DC ON/OFF button (11) again to turn it off when you stop to use it, and DC OFF character (1) will display.

* How to know if your electronic devices will work with the power station?
First, you need to determine the amount of power your electronic device requires. This may require some research by yourself, examining the user guide for your electronic device should suffice. Second, you will need to check the capacity for the individual output ports. For example, the AC port of HPS-600 is monitored by an inverter that allows for 500W of continuous power. This means if your device is pulling more than 500W for an extended period of time, the portable power supply will shut off.

WARNING :
Please do not insert any conductors into the output port deliberately.

NOTE:

1. When the power is lower than 1%, both AC and DC stop to work and turn off the power switch to protect batteries from being damaged by the loss of power.
2. When the power is lower than or equal to 10%, the battery level symbol is turned to red from green.
3. When the power level is lower than or equal to 5%, the battery level symbol flashes in red.
4. If possible, keep your power station fully charged before long-term downtime. (Please fully recharge your power station every 6 months at least for long-term usage)

2) Charging power station
a. Charging with AC cable (Max charging power: HPS-300: 120W / HPS-600/1100/1600: 200W)
Plug the charging cable into a wall outlet, then connect the other side to the DC Input port 1 (20, DC 7909) of the power station, you can see the charging state from the LCD display (2).

b. Charging with solar charger (Max charging power : HPS-300 : 120W / HPS-600/1100/1600 : 200W)

• The solar charger is optional
• Place your solar charger where it can get as much direct sunlight as possible.
• Connect the solar charger to the solar charging cable, then insert the plug of the cable into the DC Input port 2 (21, DC 5521) on the back side of the portable power station. You can know the charging state from the LCD display (2).
• It will stop charging when the battery is full of energy.

NOTE:

1. For wall charging, recharge only with the charger specified by the manufacturer.

2. Solar charging will be halted automatically for the protection of the solar chargers during the night when there is no light. In order to resume solar charging, please disconnect and re-connect the solar charger.

3. For solar charging, it is recommended to use HYUNDAI solar charger unless must use a solar charger as the following specification.
   a. Connector: DC 5521 male connector
   b. Charging type
   • MPPT Charging type
   • DC output: 12~30V (Output voltage of 24V will be better)

4. Additional controllers are not required whether charging the power station by PWM or MPPT type solar charger.

5. AC charging and solar charging are not available at the same time.

3. EC5 Port
   a. The power station has enough power to assist start a vehicle’s engine, before using the EC5, please make sure the remaining battery capacity is at least 60%.
   b. Connect the positive and negative polarities of the battery clamps to the positive and the negative polarities of the car battery (Red to +, black to -).
   c. Turn the car key to start it up.
   d. Disconnect the clamps with the battery and the jumping port of your power station.

NOTE:
Make sure the gas engine displacement of the vehicle is less than 4L.

1. Make sure the battery power is over 60%
2. Make sure the battery clamps are not broken.
3. Before starting, make sure the red and black clips are clamped tightly to the battery poles of your car, and keep the two clips at enough safety distance, to prevent the two from falling off or collision because of the engine vibration after the car starts.
4. It is strictly prohibited to connect the red and black clip directly, otherwise, it may cause accidents.
5. Please keep away from the engine when starting the car to avoid any physical injury that may cause by the car engine running.
6. Please remove the product from the battery within 30 seconds after the engine started, otherwise, it might cause damage to the portable power supply or even cause accident
7. People who are not familiar with this product (especially children) are strictly prohibited to use this function.
8. Please remove all personal jewelry, such as rings, bracelets, necklaces, and watches before jump starting.

4. Alarm information description
   a. Overload
   When the using output power is more than the specific output power to which the model can be applied, the alarm area will display “OVERLOAD”. It is necessary to reduce the power of electronic devices. If the AC output is turned off at this time, Press the AC ON/OFF button again and restart.

b. High temperature
When the internal temperature is higher than 35 degrees Celsius or the output power is greater than 200W, the cooling fan starts to work. When the internal temperature is higher than 80 degrees Celsius, the temperature alarm starts. The AC and DC outputs are off and the alarm area shows “HI TEMP”, which will stop working at once. You need to wait until the temperature drops below 40 degrees Celsius to restart.

STORAGE AND DOWNTIME MAINTENANCE

Failure to maintain your power station by following steps can result in battery damage.

1. Please charge your power station before storage and fully recharge it every 6 months at least.
   Store it in a cool and dry place.

2. If the main power supply shuts down automatically because of lower battery capacity, please recharge it within 3 months. Otherwise, the battery capacity won’t be recovered.

NOTE:
Cold temperatures (below freezing) can impact the battery capacity of the power station.
If you are living in sub-zero conditions, you can drain power from it. Never charge it in sub-zero conditions, which will damage the lithium-ion battery and the battery capacity  may not be recovered

Correct Disposal of this product
This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased.

EC
Declaration of Conformity

We :

HYUNDAI Corporation
25, Yulgok-ro 2-gil, Jongno-gu, Seoul 03143 Korea
Declare that the product detailed below :
POWER STATION
MODEL : HPS-300, HPS-600, HPS-1100, HPS-1600
Satisfies the requirements of the Council Directives :
Low voltage directive 2014/35/EU
Electromagnetic Compatibility 2014/30/EU
ROHS Directive 2011/65/EU & (EU) 2015/863
and conform with the norms :
EN 55032: 2015+A11: 2020
EN 55035: 2017+A11: 2020
EN 61000-3-2: 2019
EN 61000-3-3: 2013+A1: 2019

General Manager

Inseok Jeong

HYUNDAI Corporation
25, Yulgok-ro 2-gil, Jongno-gu,
Seoul 03143, Korea,
Post Code: 03143
+ 82 2 390 1114
www.hyundaicorp.com
Copyright HYUNDAI Corporation All rights reserved.
Made in P.R.C

References

• 현대코퍼레이션 - Global Business Partner

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>