MBRP S5267 Performance Exhaust Instruction Manual

MBRP S5267 Performance Exhaust

Product Information

This product is an MBRP Performance Exhaust system designed to improve power, sound, and driving experience. It includes various components such as a front pipe, muffler, under-axle pipe, tail pipe, and exhaust tip.

Product Usage Instructions

To install the MBRP Performance Exhaust system, follow the steps below:

Removal of Stock System

1. Apply penetrating lubricant liberally to all exhaust fasteners, hangers, and rubber insulators.
2. Mark and cut the pipe 16.25″ from the catalytic converter. Refer to Figure 1.
3. Remove the factory exhaust from the rubber insulators starting from the front and working rearward. Refer to Figure 2.

Installation of MBRP Performance Exhaust

1. Slide the 2.38″ Clamp onto the Front Pipe and install it onto the remaining factory pipe previously cut. Do not tighten any clamps until the last step. Refer to Figure 3.
2. Install the Muffler onto the Front Pipe with a 3.0″ Clamp and insert the hanger into the insulator. Support the system as you move along. Refer to Figure 4.
3. Install the Under-Axle Pipe with a 3.0″ Clamp onto the Muffler. Refer to Figure 5.
4. Slide the Tail Pipe onto the Under-Axle Pipe with a 3.0″ Clamp and insert the hanger into the rear insulator. Refer to Figure 6.
5. Install the Exhaust Tip onto the Tail Pipe. Refer to Figures 6.
6. Prior to tightening, ensure that each hanger is level where it passes through the rubber insulators. The Front Pipe should be about 1″ from the drive shaft.

Congratulations! You have successfully installed the MBRP Performance Exhaust system. You can now begin experiencing the improved power, sound, and driving experience it provides.

We hope you enjoy your purchase!

Part List

PLEASE READ BEFORE STARTING INSTALLATION
While MBRP has made every effort to ensure that all components of this system are of superior quality and properly packaged, it is the installer’s responsibility to ensure the  following before removal of the factory exhaust:

• that ALL components shown above are present.
• that ALL mating components fit together.
• that there are no damaged components.
• that the system you have purchased is appropriate for your vehicle year, model and configuration.
• that the system will not interfere with any modifications previously installed or planned.
• that you have read and understand these instructions.

If you have any questions or are uncertain about any aspect of the installation of this system to your vehicle please contact your dealer before commencing installation.

Removal of Stock System

• Apply penetrating lubricant liberally to all exhaust fasteners, hangers, and rubber insulators.

• Mark and cut the pipe 16.25” from the catalytic converter.
  Refer to Figure 1.

• Remove the factory exhaust from the rubber insulators starting from the front and working rearward.
  Refer to Figure 2.

Installation of MBRP Performance Exhaust

• Slide the 2.38” Clamp onto the Front Pipe and install onto the remaining factory pipe previously cut. Do not tighten any clamps until the last step. Refer to Figure 3.

• Install the Muffler onto the Front Pipe with a 3.0” Clamp and insert the hanger into the insulator. Supporting the system as you move along.
  Refer to Figure 4.

• Install the Under-Axle Pipe with a 3.0” Clamp onto the Muffler.
  Refer to Figure 5.

• Slide the Tail Pipe onto the Under-Axle Pipe with a 3.0” Clamp, and insert the hanger into the rear insulator.
  Refer to Figure 6.

• Install the Exhaust Tip onto the Tail Pipe.
  Refer to Figures 6.

• Prior to tightening it should be noted that each hanger is level where it passes through the rubber insulators. The Front Pipe should be about 1” from the drive shaft.

• Carefully align the system and tip. Align the edge of each band clamp with the edge of the joint it is connecting. Tighten all hardware and clamps, starting at the front and working rearward to secure the system. Check along the full length of the exhaust system to ensure there is adequate clearance for fuel lines, vent lines, brake lines, frame, bodywork, suspension and any wiring, etc. If there is any interference detected, relocate or adjust to provide adequate clearance. Ensure all clamp connections are secure and components are unable to rotate or slide. Band clamps require approximately 45 lb-ft (60 N-m) of torque. Verify clearances, system security and band clamp torque after 30-60 miles (50-100 km) of driving.

Congratulations! You are ready to begin experiencing the improved power, sound and driving experience of your MBRP Performance Exhaust.
We know you will enjoy your purchase!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>