MBRP S5528 Exhaust Armor Plus 2.5 Inch Axle Back Dual Rear Exit for 2007-2018 JEEP Wrangler or Rubicon Instruction Manual
- June 10, 2024
- MBRP
Table of Contents
MBRP S5528 Exhaust Armor Plus 2.5 Inch Axle Back Dual Rear Exit for
2007-2018 JEEP Wrangler or Rubicon
Product Information
The MBRP Performance Exhaust system is a high-performance replacement for the stock exhaust system of your vehicle. It is designed to improve the performance and driving experience of your vehicle. The MBRP Performance Exhaust system comes with all necessary parts and hardware for installation.
Product Usage Instructions
- Apply a penetrating lubricant liberally to all exhaust fasteners, hangers and rubber insulators from the stock system.
- Loosen the clamp just before the muffler on the driver’s side and remove the muffler by removing the hangers from the rubber isolators, one on each side of the muffler.
- Install the MBRP Performance Exhaust system by following the manufacturer’s instructions. Refer to Figure 6 for installation steps.
- Install the Exhaust Tips onto the Tail Pipes, check alignment and tighten.
- Congratulations! You are ready to begin enjoying the improved performance and driving experience of your MBRP Performance Exhaust system. We hope you enjoy your purchase!
Dimension
Description
PLEASE READ BEFORE STARTING INSTALLATION
While MBRP has made every effort to ensure that all components of this system
are of superior quality and properly packaged, if is the installer’s
responsibility to ensure the following before removal of the factory exhaust
- That ALL components shown above are present.
- That ALL mating components fit together.
- That there are no damaged components.
- That ihe system you have purchased is appropriate for your vehicle year, model and Configuration.
- That the system will not interfere with any modifications previously installed or planned.
- That you have read and understood these instructions.
If you have any questions or are uncertain about any aspect of fhe installation of his system fo your vehicle please contact your dealer before commencing installation.
Removal of Stock System
- Apply a penetrating lubricant liberally to all exhaust fasteners, hangers and rubber insulators.
- Start to remove the exhaust by loosening the clamp just before the muffler on the driver’s side. Refer to Figure 1.
- The muffler can be removed by removing the hangers from the rubber isolators, one on each side. Refer to Figures 1&2.
Installation of MBRP Performance Exhaust
-
Slide a 2 ½” Clamp over the Inlet Pipe and then loosely install it to the over axle pipe. Attach the Inlet Pipe hanger to the existing rubber isolator.
Refer to Figure 3. -
Slide a 2 ½” Clamp onto Muffler and loosely attach it to the Inlet Pipe. Refer to Figure 3.
-
Slide a 2 ½” Clamp over the Passenger Side Tail Pipe and install it onto the Muffler. Slide the Passenger Side Tail Pipe hanger into the existing the rubber insulator. Refer to Figure 4.
-
Slide a 2 ½” Clamp over the Driver Side Tail Pipe and install it onto the Muffler. Refer to Figure 5.
-
Install the Exhaust Tips onto the Tail Pipes check alignment and tighten
-
Tighten all hardware and clamps, starting at the front and working rearward to secure the system. Check along the full length of the exhaust system to ensure there is adequate clearance for fuel lines, vent lines, brake lines, frame, bodywork, suspension and any wiring, etc. If there is any interference detected, relocate or adjust to provide adequate clearance. Ensure all clamp connections are secure and components are unable to rotate or slide. Band clamps require approximately 45 lb-ft (60 N-m) of torque. Verify clearances, system security and band clamp torque after 30- 60 miles (50-100 km) of driving.
Congratulations! You are ready to begin enjoying the improved performance and driving experience of your MBRP Performance Exhaust system. We hope you enjoy your purchase!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>