MBRP S5207 2.5 Inch Dual Rear Exit Resonator Back Exhaust Kit Instruction Manual
- June 10, 2024
- MBRP
Table of Contents
MBRP S5207 2.5 Inch Dual Rear Exit Resonator Back Exhaust Kit
INTRODUCTION
The MBRP Performance Exhaust System is designed to improve the power, sound, and driving experience of your vehicle. The exhaust system is made of durable materials and is designed to replace yourstock exhaust system.
PLEASE READ BEFORE STARTING INSTALLATION
While MBRP has made every effort to ensure that all components of this system
are of superior quality and properly packaged, it is the installer’s
responsibility to ensure the following before removal of the factory exhaust:
- That ALL components shown above are present.
- That ALL mating components fit together.
- That there are no damaged components.
- That the system you have purchased is appropriate for your vehicle year, model and configuration.
- That the system will not interfere with any modifications previously installed or planned.
- That you have read and understand these instructions.
If you have any questions or are uncertain about any dspect of the installation of this system to your vehicle please contact your dealer before commencing installation.
OVERVIEW
Product Features
- Improved power and performance
- Enhanced exhaust sound
- Durable materials
- Direct replacement for stock exhaust system
Installation Instructions
Note: It is recommended that this product be installed by a
professional mechanic. These instructions are meant to be a general guide and
may not cover all specific vehicle makes and models.
Removal of Stock System
- Apply a penetrating lubricant liberally to all hangers and rubber isolators.
- Remove the heat shield located directly behind the factory resonator by cutting the straps. Refer to Figure 1.
- Measure 17.25 from the rear face of the resonator, mark and cut. Refer to Figure 2.
- Remove the drivers-side hanger bracket. Refer to Figure 3.
- Slide the muffler out of the passenger-side rubber isolator and remove the muffler from the vehicle.
Installation of MBRP Performance Exhaust
- Reattach the driver-side hanger bracket.
- Determine which adaptor pipe is required for your vehicle. The 1.5L Adapter is smaller than the 2.0L Adapter. The 1.5L requires a 2.17 Clamp and the 2.0L requires a 2.38 Clamp. Slide the appropriate Adaptor Pipe and Clamp onto the vehicle, do not tighten. Refer to Figure 4.
- Install the Drivers-Side Tail Pipe and Passenger-Side Tail Pipe into the factory isolators. Slide 2.5 Clamps on the end of each. Refer to Figures 5&6.
- Slide a 2.5 Clamp onto the Y-Pipe and slide onto the already installed adaptor then into the Passenger-Side Tail Pipe and the Drivers-Side Tail Pipe. Refer to Figure 7.
- Take the factory heat shield that was removed and install it onto the Y-Pipe with the supplied Gear Clamp and the 2.17 Clamp or 2.38 Clamp that will also be used to clamp the Adaptor Pipe onto the vehicle. Refer to Figure 8.
- Slide the Tips onto the Tail Pipes and adjust to your liking. Refer to Figures 9&10.
- Align the edge of each band clamp with the edge of the joint it is connecting. Tighten all hardware and clamps, starting at the front and working rearward to secure the system. Check along the full length of the exhaust system to ensure there is adequate clearance for fuel lines, vent lines, brake lines, frame, bodywork, suspension, and any wiring, etc. If there is any interference detected, relocate, or adjust to provide adequate clearance. Ensure all clamp connections are secure and components are unable to rotate or slide. Band clamps require approximately 45 lb-ft (60 N-m) of torque. Verify clearances, system security and band clamp torque after 30- 60 miles (50-100 km) of driving.
Congratulations! You are ready to begin experiencing the improved power, sound and driving experience of your MBRP performance exhaust system. We know you will enjoy your purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>