Kinderkraft Bedside Cot NESTE UP Instruction Manual
- June 13, 2024
- Kinderkraft
Table of Contents
•NESTE UP•
CO-SLEEPER
User manual
Model: Neste Up
Bedside Cot NESTE UP
The illustrations are for illustration only and do not represent the product.
All rights to this data are entirely reserved to 4Kraft Sp. z o.o. Any unauthorized use or misuse, including usufruct, copying, duplication and sharing, wholly or partially, without consent of 4Kraft Sp. z o.o. may result in legal consequences.
Dear customer
Thank you for choosing a product by Kinderkraft. Our designes are child-
oriented – safety and quality always comes first, stay comfortable knowing
that you have made the best choice.
IMPORTANT, RETAIN FOR FUTURE REFERENCE, READ CAREFULLY
SAFETY INSTRUCTIONS AND PRECAUTIONS. WARNING:
-
Do not use this product without reading the instructions for use first.
-
Stop using the product as soon as the child can sit or kneel or pull itself up.
-
Placing additional items in the product may cause suffocation.
-
Do not place the product close to another product, which could present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords, etc.
-
Do not use more than one mattress in the product.
-
The product should be placed on a horizontal floor.
-
Young children should not be allowed to play unsupervised in the vicinity of the crib.
-
The crib should be locked in the fixed position when the child is left unattended.
-
All assembly fittings should always be tightened properly.
-
Care should be taken that no screws are loose, because a child could trap parts of the body or clothing (e.g. strings, necklaces, ribbons for babies’ dummies, etc.), which would pose a risk of strangulation.
-
Be aware of the risk of burning cigarettes, open fires and other sources of strong heat, such as electric bar fires, gas fires, etc. in the near vicinity of the crib
-
Crib: maximum inclination allowed – 2 levels.
-
DO NOT use crib if any parts are missing, damaged, or broken. Contact 4Kraft Sp. z o.o. for replacement parts and instructional literature if needed. DO NOT substitute parts.
-
Only use the mattress sold with this crib, do not add a second mattress on this one, suffocation hazards.
-
For the bedside sleeper mode, use of straps (8) is required.
DO NOT use bedside sleeper if any parts are missing, damaged, or broken. Contact 4Kraft sp. z o.o. for replacement parts and instructional literature if needed. DO NOT substitute parts -
Height from the floor of the adult’s bed for which the bedside sleeper is suitable can be found on picture U.
-
Information on the types of adult bed for which the bedside sleeper is suitable can be found on picture U.
-
User shall not use other attachment system.
-
Bedside sleepers shall never be used in an inclined position
-
To prevent a suffocation hazard from entrapment, the bedside sleeper shall be properly secured to the adult bed using the attachment system.
-
There shall never be a gap between the lower side of the bedside sleeper and the mattress of the adult bed.
-
Check the tightness of the attachment system before each use by pulling the bedside sleeper in a direction away from adult bed.
-
If there is any gap between the bedside sleeper and the adult bed, DO NOT use product.
-
Gaps should not be filled with pillows, blankets or other items.
-
DANGER! – Always completely raise the drop side when not attached to the adult’s bed
-
To avoid hazards from the child’s neck being caught on the top rail on the side that is next to the adult bed, the top rail must not be higher than the adult bed mattress.
-
To avoid the risk of your child being strangled the attachment system to the adult’s bed shall always be kept away from and out of the crib.
List of baby cot components
| 1 | Side frame x2 | 6 | Crossbar |
|---|---|---|---|
| 2 | Cot material | 7 | Mattress |
| 3 | Main frame of the cot | 8 | Carrying Bag |
| 4 | Middle support of the cot’s bottom | 9 | Fastening straps |
| 5 | Side bracket in the cot padding |
Mounting of the cot:
Prepare an appropriate surface to avoid damaging the product during assembly.
Connect the side frames (1) with the main frame (3) of the cot (figure A) –
you’ll hear a “click” if it’s assembled correctly (figure B). Slide the
material (2) onto the exposed areas of the side frame (figure C). Place the
material onto the tube of the main frame and fasten the zipper (figure C1).
CAUTION! Remember to secure the zipper to prevent opening (figure D). Connect
the tube of the drop-down side to the top part of the frame (figure E) and
secure using the zipper on both ends (figure F). CAUTION! Remember to secure
the zipper to prevent opening (figure G). Slide the ends of the side bracket
(5) in the cot padding material into the relevant openings in both side frames
(figure H). Next, connect the bracket to the legs of the cot by sliding it in
along both sides into the relevant openings (figure H, I). You’ll hear a
“click” if it’s assembled correctly. Place the cot on the side opposite to the
drop-down side. Slide the bar (6) into the legs and make sure that the latches
on both sides are secured (figure J). Place the cot back in the vertical
position.
Connect the bottom bracket (4) to the legs of the cot, and slide it in along
both sides until it locks – you’ll hear a distinctive “click” when this
happens (figure K). Slide the material of the cot over the bottom bracket, and
affix with a large hook-and-loop closure (figure L). Affix the bottom bracket
(4) to the base of the cot using three small hook-and-loop closures (figure
M).
Wrap the hook-and-loop closures around the brackets on the side of the cot
(figure N). Place the mattress in the cot. The assembled product is shown in
figure O.
Height adjustment:
The cot is adjustable to 5 different heights. To adjust the desired height hold the cot with your foot, move button A sideways while pressing button B and adjust the frame of the cot to the desired height (fig.P).
Bedside cot:
To connect the cot to the parents’ bed, remove the safety devices at the locks
(fig. R). Unlock the zips on both sides (fig. S). Slide the lever and slide
out the tube of the side panel (fig. T).
Repeat on the other side. Remove the side panel of the cot (fig. W) and pull
the tube out of it.
Adjust the height of the cot to the parents’ bed (fig. U). Fasten the buckle
of the fastening straps to the cot (fig. X). Interleave the straps either
through the whole bed or only through its side bar (fig. Y) and adjust so that
the cot is fixed securely to the parents’ bed (fig. Z). Roll the loose parts
of the straps (9) under the cot. To move the cot as close as possible to the
base of the parent’s bed, move button A sideways (fig. AA) and at the same
time press button B. Move the legs to the desired distance. ATTENTION! Make
sure that the straps are properly adjusted and the cot is adjacent to the
mattress of the parents’ bed (fig. Z).
Locking the wheels:
The cot has 2 wheels that allow to move the cot and to connect it with the parents’ bed. To lock the wheels, press the locking button down. To unlock, move the button upwards (fig. AB).
Maintenance and cleaning
Frame – clean with a soft, clean and dry cloth.
| Wash at max. 30°C, gentle process.| | Do not wash. Clean the product gently
with a damp cloth and a mild detergent.
---|---|---|---
| Do not bleach| | Do not iron
| Do not dry in a tumble dryer| | Do not dry clean
Do not fold or store the product when it is wet and never store it in wet conditions, as it can lead to mould growth.
In the interests of our Clients – we are at your disposal! If you have a problem with the product you received, contact us in the most convenient way for you!
International: support@kinderkraft.com
(0048) 61 646 02 37
FABRIKANT
4Kraft Sp. z o.o. ul. Tatrzariska 1/5 60-413 Poznan, Poland