GOLDEN LIGHTING 6930-WSC VFG-IL Cay 2 Light Vintage Fired Gold Wall Sconce Wall Light Instruction Manual

June 13, 2024
GOLDEN LIGHTING

GOLDEN LIGHTING 6930-WSC VFG-IL Cay 2 Light Vintage Fired Gold Wall Sconce Wall Light

GOLDEN LIGHTING 6930-WSC VFG-IL Cay 2 Light Vintage Fired Gold Wall Sconce
Wall Light

Dimension

Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.
Dimension

Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.
Dimension

Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
Dimension

We appreciate your business and hope you love your new light!

Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.

Assembly Instructions

How to Identify the Fixture’s Wires

How to Identify the Fixture’s Wires

Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread

Assembly Instructions

For Customer Service, contact the place of purchase to arrange for replacement parts.

IMPORTANT:

  • All installation work should be done by accredited professional.
  • Shut off power supply at fuse or circuit breaker!
  • Use only the specified bulbs. Do not exceed the maximum wattage!

PREPARING FOR INSTALLATION

Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. From the parts bag remove the mounting strap (A) assembly, One end of the nipple (F) should be attached to mounting strap (A) with washer (C) and hex nut (D) in place. Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver. Tighten the screws securely.

ASSEMBLING THE FIXTURE

No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.

CONNECTING THE WIRES

2. Have an assistant support the fixture’s weight while completing the wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.

FINISHING THE INSTALLATION

3. Place backplate (G) onto over mounting strap (A) until the nipple (F) protrude through holes in the front of the backplate (G). Thread deco nuts (N) onto nipple (F) firmly. Twist until backplate (F) is snug against the wall. 4.
Attach candle sleeve (L) onto socket and install a light bulb (not included) into socket in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. 5. Carefully attach fabric shade (I) to backplate (G) and secure with the small screws (H) to the top holes of backplate (G). 6. Attach deco leaf accent (O) to the hook (M) on backplate (G). Your installation is now complete. Turn on the power and test the fixture.

Customer Support

Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…

@GoldenLighting
@GLFixtures
@GoldenLighting1
@GoldenLighting
Get help, quick tips, and explore curated content
QR-Code

Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

GOLDEN LIGHTING User Manuals

Related Manuals