GOLDEN LIGHTING 9020-LP BLK Kinsington Linear Pendant Ceiling Light Instruction Manual
- June 13, 2024
- GOLDEN LIGHTING
Table of Contents
**GOLDEN LIGHTING 9020-LP BLK Kinsington Linear Pendant Ceiling Light Instruction Manual
**
Thank You for Choosing Golden Lighting for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the counter
top.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
Assembly Instructions
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. Take the mounting strap assembly from the parts bag.
Mounting strap (B) contains several threaded holes. Two sets of mounting
screws (A & D) should be attached to mounting strap (B). You may need to
tighten nuts (C) that hold mounting screws (A) in place. If the screws are not
attached, please hold canopy (F) up to mounting strap (B). Line up the holes
in canopy (F) with the holes in mounting strap (B) and insert mounting screws
(A) into mounting strap (B) so that mounting screws (A) protrude through the
holes in canopy (F). Mounting screws (A) are long, so please test canopy (F)
against the mounting strap and practice threading deco nuts (H) onto mounting
screws (A) to see how far you should thread nuts (C). Remove the deco nuts (H)
and canopy (F). Tighten nuts (C) onto mounting screws (A) to hold the screws
in place. 2. Pull the house wires through the center of mounting strap (B).
Secure mounting strap (B) to the junction box with mounting screws (D) and a
screwdriver. Tighten the screws securely.
ASSEMBLING THE FIXTURE
Set fixture on floor for assembly. Measure to determine the correct length of chain needed for proper hanging height. If necessary, use a pair of pliers to open and remove any excess chain. Attach chain connectors (J) to each end of chains (I). Attach one end of both the chain connectors/chains to top loops (K). Connect the remaining ends of the chain connectors/chains to canopy loops (G). Close the chain connectors to secure.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Push canopy (F) up to mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (F). Tightly thread decorative nuts (H) onto the threads of mounting screws (A) to secure the canopy in place.
Thread until canopy (F) is snug against the ceiling. Install light bulbs (not provided) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is complete. Turn on the power and test the fixture.
Get help, quick tips, and explore curated content
@GoldenLighting
@GLFixtures
@GoldenLighting1
@GoldenLighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>