GOLDEN LIGHTING 3879-M BCB-NB 1 Light 15.88 inch Brushed Champagne Bronze Pendant Ceiling Light Instructions
- October 31, 2023
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 3879-M BCB-NB 1 Light 15.88 inch Brushed Champagne Bronze Pendant Ceiling Light
Thank You for Choosing Golden Lighting for Your Lighting Needs!
Installation
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor.
Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
**Get help, quick tips, and explore curated content
**
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap.
-
From the parts bag remove the mounting strap assembly.
One end of nipple (F) should be attached to mounting strap (A) with washer (C) and hex nut (D) in place. The other end should have canopy loop (H) attached. Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver. Tighten securely. -
Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop (H) to test the height. Approximately half of the canopy loop’s exterior threads should be exposed, and the canopy loop collar (I) should fit snugly onto the canopy loop (H). Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H) until the desired height is reached.
ASSEMBLING THE FIXTURE -
Measure to determine the correct number of rods (J) needed for proper hanging height. To shorten the fixture, slide the desired number of excess rods off. If additional rods are needed, please contact the place of purchase to order more. Lock the top loop (L) to the rod (J). Feed the fixture wires from post (R) through rod (J), top loop (L), canopy loop collar (I) chain connector (K), canopy loop (H), and canopy (G). Pull the wires until taut. Thread rods (J) onto post (R).
-
Use the chain connector (K) to attach the fixture body to the canopy. Put the chain connector (K) on top loop (L) and canopy loop (H). Close the chain connector (K) to secure.
CONNECTING THE WIRES -
Have an assistant support the fixture’s weight while completing the wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
-
Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy. Tightly thread canopy loop collar (I) onto canopy loop to secure canopy (G) in place.
-
Hang hooks (N) to the upper iron rings (O) and lower iron rings (P) to connect the shade (S) and fixture (M) together.
-
Install a light bulb (not provided) into socket (Q) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is complete. Turn on the power and test the fixture.
Customer Service
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
@GoldenLighting
@GLFixtures
@GoldenLighting1
@GoldenLighting
