GOLDEN LIGHTING 1830-LP BLK-OP Neela Linear Pendant Ceiling Light Instruction Manual

GOLDEN LIGHTING 1830-LP BLK-OP Neela Linear Pendant Ceiling Light

Product Information

Thank You for Choosing Golden Lighting for Your Lighting Needs!

• Product Model: 1830-LP
• Fixture Type: Pendants & Linear Pendants
• Suitable for: Kitchen Island, Dining Room Table, Open Areas
• Features: Dimmable, Layered Lighting
• Maximum Recommended Wattage: Not provided

Product Usage Instructions

Pendants & Linear Pendants Above a Kitchen Island

• Center a linear pendant over the island.
• If hanging pendants, use one pendant for every 24″ of island.
• Fixtures should hang at least 30″ above the countertop.

Pendants & Chandeliers Above a Dining Room Table

• Fixtures should stay at least 30″ above the table.
• Use a fixture that is 12″ narrower than the width of the table.

Pendants and Chandeliers in Open Areas

• The bottom should hang at least 7.5 feet from the floor.
• Allow clearance for any opening doors.

Installation Instructions

1. Prepare for installation.
2. Assemble the fixture according to the provided assembly instructions.
3. Connect the wires following the identified fixture wires and house wires.
4. Finish the installation by pushing the canopy up to the ceiling and tightening decorative nuts onto the exposed threads of mounting screws.
5. Slide shades over sockets and use socket rings to secure the shade to the socket. Twist socket rings until secure.
6. Install light bulbs (not provided) according to the fixture’s specifications. Do not exceed the maximum recommended wattage.
7. Turn on the power and test the fixture to ensure proper functioning.

For any issues or replacement parts, please contact the place of purchase. We appreciate your business and hope you love your new light!  For further product information, expert lighting advice, and coordinating lights, visit our website www.GoldenLighting.com.

Follow us on Social Media: @GoldenLighting,
@GLFixtures,
@GoldenLighting1,
@GoldenLighting

Thank You for Choosing Golden Lighting for Your Lighting Needs!

Assembly Instruction

Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.

Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.

Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.

We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social..

How to Identify the Fixture’s Wires

Hot: Smooth, Black, or Transparent with Black Inner Thread

Get help, quick tips, and explore curated content

Parts

For Customer Service, contact the place of purchase to arrange for replacement parts.

IMPORTANT:

• All installation work should be done by accredited professional.
• Shut off power supply at fuse or circuit breaker!
• Use only the specified bulbs. Do not exceed the maximum wattage!

PREPARING FOR INSTALLATION

Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power
at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. From the parts bag remove the mounting strap assembly. Mounting strap (B) contains threaded holes. Two sets of mounting screws (A & D) should be attached to the mounting strap (B). You may need to tighten nuts (C) that hold mounting screws (B) in place. Place mounting strap (B) over the junction box so that mounting screws (A) are vertical, and in alignment with the hole locations on the fixture’s canopy (F). Pull house wires through the center of the mounting strap (B). Secure mounting strap (B) to the junction box with mounting screws (D) and a screwdriver. Tighten the screws securely.

ASSEMBLING THE FIXTURE

• Measure to determine the correct number of rods (L) needed for proper hanging height. There are three 12-inch rods and one 6-inch rod included for each side of the fixture. To shorten the fixture, slide the desired number of excess rods off. To lengthen the fixture, add additional rods. If additional rods are needed, please contact the place of purchase to order more. Feed the fixture wires from posts (M) through the caps (T) and rods (L).
• Feed the fixture wires through the swivel posts (K) and through the top of the canopy (F). Thread the bottom rods onto posts (M) at the top of the fixture’s body. Thread rods (L) together and pull the wires until taut. Twist the top rods (L) onto the threads of swivel posts (K) of the canopy (F). Secure swivel posts (K) to canopy (F) by tightening hex nuts (G) over washers (H and I). Trim the wires to the desired length plus 8 to 10 inches.

CONNECTING THE WIRES

• Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.

FINISHING THE INSTALLATION

• Push the canopy (F) up to the ceiling and tightly thread decorative nuts (J) onto the exposed threads of mounting screws (A). 6. Slide shades (P) over sockets (N) and use socket rings (O) to secure the shade to the socket. Twist socket rings (O) until secure. Install light bulbs (not provided) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is complete. Turn on the power and test the fixture.

GoldenLighting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>