Front FF959 Bolt On Rugged Look Fender Flares Instruction Manual

Front FF959 Bolt On Rugged Look Fender Flares

Product Information

Product Name: Front Bolt-On/Rugged Look Fender Flares

Compatible Vehicle: Chevy Silverado 1500 (model years 2019-2022)

Model Number: FF959

Hardware Included:

• Extrusion U Clip: 6 pieces
• .6mm Large Clip: 4 pieces
• .9mm Black Spacer: 2 pieces
• Alcohol Towelette: 4 pieces
• Abrasive Resistant Tape: 4 pieces
• Speed Nut: 2 pieces
• Bolt Kit (Nuts and Torx Drive Bolts): 44 pieces each

Product Usage Instructions

Front Fender Flare Installation

• STEP 1: Attach the extruded plastic bolts. Peel back the white tape liner from the bottom side of the extruded plastic bolt and press until it snaps into place. Ensure the inside of the Fender Flares where the rubber seal is attached is clean, using the provided alcohol wipes. Wipe away any residue with a dry, clean cloth.
• STEP 2: Attach the included rubber seal to the Fender Flares. Peel back 2 adhesive backings and position them on the Fender Flare. Attach the seal to the Fender Flare, peeling back a few inches at a time. Apply pressure to secure the rubber seal to  the Fender Flare edge. Attach the rubber seal along all areas where the Fender Flare will make contact with the vehicle body.
• STEP 3: Trim excess rubber seal and discard.
• STEP 4: Clean the body areas where the Fender Flares will make contact. Ensure the fenders are dry prior to installation. Turn the tires outward for Fender Flare installation.
• STEP 5: For models with front factory mud guards, remove them using a #15 Torx head screwdriver at the upper and lower screw locations, and an M10 socket at the underside location indicated above. Retain the factory mud guards for later use if required, as the fender flares require the mud guards to be removed.
• STEP 6: Place the Fender Flare on the vehicle into the position of best fit. Note the slots in the Fender Flare at positions A and B, as well as the vehicle wheel arch. Remove the Fender Flare. Place small abrasive resistant tapes over the fender lip at positions A and B. Slide the large clips over the inner fender panel at positions A and B, ensuring the hook on the back of the clip engages over the fender lip.
• STEP 7: Place the Fender Flare on the vehicle into the desired position.
• STEP 8: Install the speed nut over the inner bumper panel at the indicated location.
• STEP 9: Starting at the front of the Fender Flare, carefully remove the tape liner from the extrusion a few inches at a time. Ensure that the extrusion is not tucking into the flare and sits flush neatly against the fender body. Apply forward pressure to adhere the extrusion along the edge of the entire length of the Fender Flare once the extrusion liner is removed. Ensure all fixing points are tight and secure, and that the extrusion is flush neatly against the vehicle body. Repeat the installation steps for the opposite side.
• Rear Fender Flare Installation
• STEP 10: Attach the extruded plastic bolts. Peel back the white tape liner from the bottom side of the extruded plastic bolt and press until it snaps into place. Ensure the inside of the Fender Flares where the rubber seal is attached is clean, using the provided alcohol wipes. Wipe away any residue with a dry, clean cloth.

Important: Please read instructions entirely before installing this product

Hardware Included| QTY|  | Hardware Included| QTY|  | Bolt Kit Included|

QTY

---|---|---|---|---|---|---|---
Extrusion| 36ft| Alcohol Towelette| 4
U CLIP .6mm| 6| Abrasive resistant tape| 4| Nuts| 44
Large CLIP .9mm| 4| Speed nut| 2| Torx drive Bolts| 44
Black Spacer| 2|  |  |  |

Ensure that both left and right hand Fender Flares suit the profile of the vehicle. Note the areas where the Fender Flares come in contact with the vehicle. NOTE: Before fitting Fender Flares remove any moldings, strips or existing flares from the wheel arch. If there is a body side molding, mark where the molding is to be cut, alternatively the Fender Flare can be cut to go around the molding. Be sure to allow enough room for the extrusion. No drilling of vehicle is required for Trox drive bolts and nuts.

Installation Instructions

• STEP 1: Attach the extruded plastic bolts. Peel back white tape liner from the bottom side of the extruded plastic bolt and press until it snaps into place. Ensure inside of Fender Flares where the rubber seal is attached is clean, using the alcohol wipes provided. Wipe away any residue with a dry clean cloth.
• STEP 2: Attach the included rubber seal to the Fender Flares. Peel back 2” of the adhesive backing and position on the Fender Flare. Attach the seal to the Fender Flare, peeling back a few inches at a time. Ensure pressure is used to secure rubber seal to Fender Flare edge. Attach rubber seal along all areas the Fender Flare will make contact with the vehicle body.

• STEP 3: Trim excess rubber seal and discard.
• STEP 4: Clean the body areas where the Fender Flares will make contact. Ensure fenders are dry prior to install. Turn tires outward for Fender Flare installation.

• STEP 5: For models with front factory mud guards, remove using #15 Torx head screwdriver at the upper and lower screw locations from the front factory mudguards and M10 socket at the underside location indicated above, maintain #15 Torx head screws for re-install . Retain factory mudguards for later use if required, fender flares require the mud guards to be removed.
• STEP 6: Place Fender Flare on the vehicle into the position of best fit. Note where the slots in Fender Flare at positions A , B and vehicle wheel arch. Remove Fender Flare. Place the small abrasive resistant tapes over the fender lip at the noted posistions A, B. Slide the large clips over the inner fender pannel at the noted A, B positions, ensure the hook on the back of the clip engages over the fender lip.

• STEP 7: Place Fender Flare on the vehicle into the position of best fit. Peel back 2 inches of the red tape liner on the fender flare extrusion at both ends, ensure liner is on the outside of part ref to step 9. Using #15 Torx head screwdriver re-install previously removed factory mudguard screws at the upper and lower screw locations through the slots in the Fender Flare at the two noted locations. At the noted A, B positions secure the Fender Flare to the wheel arch by ensuring the notch in clip locates securely into the slot in the Fender Flare.
• STEP 8: Install the speed nut over the inner bumper pannel at the slot location in the front of the fender flare. Align the slot in the fender flare over the hole in the speed nut. Mark this location on the inner bumper pannel with a grease pencil. Use a 1/4 “ drill bit to drill the bumper pannel at the previously marked location. Install the speed nut over the drilled hole location flat side facing the wheel well. Slide the spacer between the inner side of the fender flare large flat side facing the wheel well centered over the hole in the speed nut. Install one of the factory screws removed from step 5 through the slot in the fender flare, spacer and into the hole in the speed nut. Apply inward pressure on fastening point and tighten screw, ensure the screw engages through both sides of the speed nut.

• STEP 9: Starting at the front of the Fender Flare, carefully remove tape liner from extrusion a few inches at a time. Ensure extrusion is not tucking into flare and sits flush neatly against the fender body. Apply forward pressure to adhere the extrusion along the edge of entire length of Fender Flare once extrusion liner is removed. Ensure all fixing points are tight and secure and that the extrusion is flush neatly against the vehicle body. Repeat install steps for the opposite side.

• STEP 10: Attach the extruded plastic bolts. Peel back white tape liner from the bottom side of the extruded plastic bolt and press until it snaps into place. Ensure inside of Fender Flares where the rubber seal is attached is clean, using the alcohol wipes provided. Wipe away any residue with a dry clean cloth.
• STEP 11: Attach the included extrusion to the Fender Flares. Peel back 2” of the adhesive backing and position on the Fender Flare. Attach the extrusion to the Fender Flare, peeling back a few inches at a time. Ensure pressure is used to secure extrusion to Fender Flare edge. Attach extrusion along all areas the Fender Flare will make contact with the vehicle body. Trim excess extrusion. Attach extrusion to the bottom front corner of Fender Flares per the attached image that will locate around the factory spat.

• STEP 12: Clean the body areas where the Fender Flares will make contact. Ensure fenders are dry prior to install.
• STEP 13: Using #15 Torx head screwdriver remove upper screw from the front factory spat in the rear wheel arch. Maintain screws for re-install.

• STEP 14: Using #15 Torx head screwdriver remove the two botton screws from the rear factory spat. Maintain screws for re-install.
• STEP 15: Place Fender Flare on the vehicle into the position of best fit. Note where the slots in Fender Flare align with the previously removed factory screws in the front and rear spats. Peel back 2 inches of the red tape liner on the fender flare extrusion at both ends, ensure liner is on the outside of part ref to step 18.Using #15 Torx head screwdriver re-install the upper and lower screws from the rear factory spat through the slots in the Fender Flare.

• STEP 16: Using #15 Torx head screwdriver re-install the upper screw from the front factory spat in the rear wheel arch through the slot in the Fender flare.
• STEP 17: To secure the Fender Flare to the body, apply upward tension on Fender Flare to the vehicle fender when installing the black metal clips. Slide the clips over the Fender Flare and the inner wheel arch lip in the three locations shown. Position the clip so that the barb in the clip locates in the slot of the Fender Flare. Ensure all fixing points are tight and secure and that the extrusion is flush neatly against the vehicle body. Repeat install steps for the opposite side.
  Note: If sealant bead in the inner wheel lip prevents the clips from engaging the slot in the part, with a sharp utility knife cut away the mastic seal that corresponds to the noted clip locations. Cut width of clip and 10mm either side of the locations, to ensure enough selant has been removed test clip to ensure this engages the slot in the part.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>