GOLDEN LIGHTING 7646-6 Serafina 6 Light 24.5 inch Golden Aura Chandelier Ceiling Light Instruction Manual
- June 13, 2024
- GOLDEN LIGHTING
Table of Contents
Thank You for Choosing Golden Lighting for Your Lighting Needs!
7646-6 Serafina 6 Light 24.5 inch Golden Aura Chandelier Ceiling Light
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor.
Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Assembly Instructions: 7646-6
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap.
-
From the parts bag remove the mounting strap (A) assembly. One end of the nipple (B) should be attached to the mounting strap (A) with a washer and hex nut in place. Attach mounting strap (A) to the junction box using mounting screws (C) and a screwdriver. Tighten securely.
Unscrew canopy loop collar (G) from canopy loop (F). Pass canopy (D) over the mounted canopy loop (F) to test the height. Approximately half of the canopy loop’s exterior threads should be exposed, and the canopy loop collar (G) should fit snugly onto the canopy loop (F). Remove canopy (D) and adjust the height of nipple (B) and canopy loop (F) until the desired height is reached.
ASSEMBLING THE FIXTURE -
Feed the fixture’s wires from the post (K) through the top loop (J). Carefully push the wires through the hole in the top loop (J). Thread top loop (J) onto post (K) to secure top loop to the fixture. Pull the wires until taut. Adjust the 6pcs arms (Q) to a uniform distribution.
-
Measure to determine the correct length of chain needed for proper hanging height. If necessary, use a pair of pliers to open and remove any excess chain. Attach each of the chain connectors (H) to each end of chain (I) before attaching one end of the chain
connector/chain to top loop (J). Connect the other chain connector (H) to the canopy loop (F). Close the chain connectors (H) to secure. -
Feed the fixture’s wires up through the chain (I) (every three links or so), pulling the wires until taut. Gently slide canopy loop collar (G) and canopy (D) down onto the chain/wires. Trim excess wires leaving about 8 to 10 inches for later.
CONNECTING THE WIRES -
Have an assistant support the fixture’s weight while completing the wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION -
Push canopy (D) up to the ceiling and slide canopy loop collar (G) up beneath the canopy. Tightly thread canopy loop collar (G) onto canopy loop (F) to secure canopy in place until snug against the ceiling. Carefully slide candle sleeves over sockets (N) into the cups (R). Install light bulbs (not included) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. 7. Hang decorative strands onto the frame of the fixture (Q) by hooking the ends (P & P1) of decorative strands onto the loops (O & O1) on the fixture’s body. Your installation is now complete. Turn on the power and test the fixture.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
@GoldenLighting
@GLFixtures
@GoldenLighting1
@GoldenLighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>