GOLDEN LIGHTING 1140-SF BLK-HWG Samara 2 Light 15.38 inch Matte Black Semi-Flush Ceiling Light Instruction Manual
- June 13, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 1140-SF BLK-HWG Samara 2 Light 15.38 inch Matte Black
Semi-Flush Ceiling Light
Thank you for choosing Golden Lighting for your lighting needs!
Product Information
- Product Name: 1140-SF
- Color: Black
- Model: 1140-SF BLK-HWG
Product Usage Instructions
- Pendants & Linear Pendants Above a Kitchen Island:
- Center a linear pendant over the island.
- If hanging pendants, use one pendant for every 24 inches of the island.
- Fixtures should hang at least 30 inches above the countertop.
- Pendants & Chandeliers Above a Dining Room Table:
- Fixtures should stay at least 30 inches above the table.
- Use a fixture that is 12 inches narrower than the width of the table.
- Pendants and Chandeliers in Open Areas:
- The bottom should hang at least 7.5 feet from the floor.
- Allow clearance for any opening doors.
- General Tips for Lighting:
- Layer your lighting to have both task and ambient lighting.
- Coordinating fixtures like sconces, flush mounts, and pendants can help meet your layered lighting needs and reinforce your desired aesthetic.
- Install lights with dimmers to control the level of light output.
Please note that no assembly is required for this product (1140-SF). It
arrives fully assembled and ready for installation.
For any customer service or replacement parts, please contact the place of
purchase. For more information, help, quick tips, and curated content, please
visit our website at GoldenLighting.com. We
appreciate your business and hope you love your new light! If you would like
to share a picture of your light, tag us on social media
using the following handles:
- Instagram: @GoldenLighting
- Twitter: @GLFixtures
- Facebook: @GoldenLighting1
If you have any further questions or need assistance, please visit our website or contact us through the provided customer service channels. Thank you once again for choosing Golden Lighting. Enjoy your new light!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure
the best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment. Get function and style! Browse our site for coordinating lights
and expert lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
How to Identify the Fixture’s Wires **
**
Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement
parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap.
- Mounting strap (B) contains several threaded holes. Two sets of mounting screws (A & D) should be attached to mounting strap (B). You may need to tighten nuts (C) that hold mounting screws (A) in place. If the screws are not attached, please hold canopy (F) up to mounting strap (B). Line up the holes in canopy (F) with the holes in mounting strap (B) and insert mounting screws (A) into mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (F). Mounting screws (A) are long, so please test the canopy against the mounting strap to see how far you should insert the screws.
- Attach mounting strap (B) to the junction box using mounting screws (D) and a screwdriver. Tighten the screws securely. Pull the house wires through the center of mounting strap (B).
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply
wires from the junction box. Attach the fixture’s wires to the power supply
wires from the junction box. Connect Hot to Hot (transparent wire with black
inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with
white inner thread, white, or ribbed wire), and Ground to Ground (transparent
wire with green inner thread, green wire, or copper). Twist the ends of the
wire pairs together, and then twist on a wire connector. Make sure all twists
are in the same direction. If there is no house ground wire coming from the
junction box, locate ground screw (E) on the mounting bracket/mounting strap
and wrap the fixture’s ground wire around the ground screw. Use a screwdriver
to tighten the top of ground screw (E) onto the wires and into the mounting
bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Push canopy (F) up to the ceiling until mounting screws (A) protrude from the
holes in the canopy (F). Thread deco nuts (G) onto the exposed threads of
mounting screws (A) until snug against the ceiling to secure. Install light
bulbs (not provided) into sockets in accordance with the fixture’s
specifications. Do not exceed the maximum recommended wattage. Thread the
washer (J), glass shade (I) and washer (J) onto nipple (H) as shown in the
diagram. Secure with finial (K). Your installation is complete. Turn on the
power and test the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>