GOLDEN LIGHTING 1067-OSF Piper Modern Natural Black Outdoor Flush Mount Light Instruction Manual
- June 13, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 1067-OSF Piper Modern Natural Black Outdoor Flush Mount
Light
Product Information
Thank You for Choosing Golden Lighting for Your Lighting Needs!
- Product Model : 1067-O3P/1067-OSF
- Product Type : Pendants & Linear Pendants
Product Features
- Can be used above a kitchen island, dining room table, or in open areas
- Provides both task and ambient lighting
- Coordinates with other fixtures like sconces, flush mounts, and pendants
- Can be installed with dimmers for adjustable light output
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one
pendant for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom of the fixture should hang at least 7.5 feet from the floor.
Allow clearance for any opening doors.
Installation Instructions
- Prepare for Installation
- Gather all necessary parts and tools.
- Ensure power to the installation area is turned off.
- Assemble the Fixture
- Feed the fixture wires from the nipple into the nipple cover found on the canopy until the wires come out of the top of the canopy.
- Thread the nipple cover onto the nipple and fasten it.
- Pull the wires until taut and trim them to the desired length plus 8 to 10 inches.
- Connect the Wires
- Identify the fixture wires (Hot, Neutral, Ground) and the house wires.
- Connect the corresponding wires using wire connectors.
- Finish the Installation
- Securely attach the fixture to the mounting surface.
- Turn on power and test the fixture.
We appreciate your business and hope you love your new light! For any customer
service inquiries or replacement parts, please contact the place of purchase.
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off? Follow us, share a picture, and tag
us on Social…
Follow us on
Thank You for Choosing Golden Lighting for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
- We appreciate your business and hope you love your new light!
- Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating
- fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
- Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit
- www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
Assembly Instructions: 1067-O3P/1067-OSF
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. PLEASE NOTE THAT THE FIXTURE MAY BE HUNG AS A PENDANT OR A
SEMI-FLUSH, PLEASE DECIDE HOW YOU WOULD LIKE THE FIXTURE TO BE INSTALLED AND
REFER TO THE RELATED INSTRUCTIONS.
FOR PENDANT INSTALLATION REFER TO THE DIAGRAM LABELED “(1)”
- From the parts bag remove the mounting strap assembly. One end of nipple (F) should be attached to mounting strap (A) with washer (C) and hex nut (D) in place. The other end should have canopy loop (H) attached. Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver. Tighten securely. 2. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop (H) to test the height. Approximately half of the canopy loop’s exterior threads should be exposed, and the canopy loop collar (I) should fit snugly onto the canopy loop (H). Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H) until the desired height is reached. FOR SEMI-FLUSH INSTALLATION REFER TO THE DIAGRAM LABELED
- Mounting strap (B) contains several threaded holes. Two sets of mounting screws (A & D) should be attached to mounting strap (B). You may need to tighten nuts (C) that hold mounting screws (A) in place. If the screws are not attached, please hold canopy (F) up to mounting strap (B). Line up the holes in canopy (F) with the holes in mounting strap (B) and insert mounting screws (A) into mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (F). Mounting screws (A) are long, so please test the canopy against the mounting strap to see how far you should insert the screws. 2. Attach mounting strap (B) to the junction box using mounting screws (D) and a screwdriver. Tighten the screws securely. Pull the house wires through the center of mounting strap (B).
ASSEMBLING THE FIXTURE
FOR PENDANT INSTALLATION REFER TO DIAGRAM LABELED
- Measure to determine the correct number of chain links needed for proper hanging height. If necessary, use a pair of pliers to open and remove any excess chain. Attach one chain connector (K) to each end of chain (J). Attach one end of the chain/chain connector to top loop (L). Feed the fixture wires from the fixture body (N) through nipple (M). Pull the wires until taut. Thread washer (S) onto nipple (M). Thread top loop (L) onto nipple (M). Attach the remaining end of the chain/chain connector to canopy loop (H). Close chain connectors (K) to secure. Feed fixture wires from nipple (M) through top loop (L), the chain (J) (every three links or so), canopy loop collar (I), canopy loop (H), and canopy (G). Pull the wires until taut. Gently slide canopy loop collar (I) and canopy (G) down onto the chain/wires. Trim the wires to the desired length plus 8 to 10 inches. FOR SEMI-FLUSH INSTALLATION REFER TO DIAGRAM LABELED
- Feed the fixture wires from the fixture body (N) through nipple (M). Pull the wires until taut. Thread washer (S) onto nipple (M).
Feed fixture wires from nipple (M) into the nipple cover (H) found on canopy (F) until the wires comes out of the top of canopy (F). Thread nipple cover (H) onto nipple (M) and fasten it. Pull the wires until taut. Trim the wires to the desired length plus 8 to 10 inches.
CONNECTING THE WIRES
4. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
FOR PENDANT INSTALLATION REFER TO DIAGRAM LABELED “(1)”: 5. Push canopy (G) up
to the ceiling and slide canopy loop collar (I) up beneath the canopy (G).
Tightly thread canopy loop collar (I) onto canopy loop (H) to secure canopy
(G) in place. 6. Slide glass shades (R) over the sockets (P) into cups (O) and
secure in place with socket rings (Q). Install light bulbs
(not included) into socket (P) in accordance with the fixture’s
specifications. Do not exceed maximum recommended wattage. After installing
the fixture, apply a clear silicone rubber caulking to seal the gap between
the canopy (G) and the mounting surface. Your installation is complete. Turn
on the power and test the fixture. FOR SEMI-FLUSH INSTALLATION REFER TO
DIAGRAM LABELED “(2)”: 5. Push canopy (F) up to the ceiling until mounting
screws (A) protrude from the holes in the canopy (F). Thread deco nuts (G)
onto the exposed threads of mounting screws (A) until snug against the ceiling
to secure. 6. Slide glass shades (R) over the sockets (P) into cups (O) and
secure in place with socket rings (Q). Install light bulbs (not included) into
socket
(P) in accordance with the fixture’s specifications. Do not exceed maximum
recommended wattage. After installing the fixture, apply a clear silicone
rubber caulking to seal the gap between the canopy (F) and the mounting
surface. Your installation is complete. Turn on the power and test the
fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>