SENECA ZE-2AI Automation Interfaces Ethernet Instruction Manual
- June 4, 2024
- SENECA
Table of Contents
SENECA ZE-2AI Automation Interfaces Ethernet
PRELIMINARY WARNINGS
The word WARNING preceded by the symbol indicates conditions or actions that put the user’s safety at risk. The word ATTENTION preceded by the symbol indicates conditions or actions that might damage the instrument or the connected equipment. The warranty shall become null and void in the event of improper use or tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if the instructions contained in this manual are not followed.
- WARNING : The full content of this manual must be read before any operation. The module must only be used by qualified electricians. Specific documentation is available via QR-CODE shown on page 1.
- The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to electrostatic discharges. Take appropriate measures during any operation.
- Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling). The symbol on the product or its packaging shows the product must be surrendered to a collection centre authorized to recycle electrical and electronic waste.
- DOCUMENTATION ZE-4DI-2AI-2DO
- DOCUMENTATION Z-4DI-2AI-2DO
- DOCUMENTATION ZE-2AI
- SENECA s.r.l.; Via Austria,
- 26 – 35127 – PADOVA
- ITALY; Tel. +39.049.8705359
- Fax +39.049.8706287
CONTACT INFORMATION
- Technical support
- support@seneca.it
- Product information
- sales@seneca.it
This document is the property of SENECA srl. Copies and reproduction are
prohibited unless authorized. The content of this document corresponds to the
described products and technologies.
Stated data may be modified or supplemented for technical and/or sales
purposes.
MODULE LAYOUT
- Single module dimensions LxHxD: 17.5 x 102.5 x 111 mm;
- Weight : 110 g;
- Enclosure: PA6, black
- Double module dimensions LxHxD: 35 x 102.5 x 111 mm;
- Weight: 110 g;
- Enclosure: PA6, black
LED SIGNALS ON THE FRONT PANEL (ZE-4DI-2AI-2DO)
LED SIGNALS ON THE FRONT PANEL (Z-4DI-2AI-2DO)
LED SIGNALS ON THE FRONT PANEL (ZE-2AI)
TECHNICAL SPECIFICATIONS
INSTALLATION REGULATIONS
The module has been designed for vertical installation on a DIN 46277 rail. For optimal operation and long life, adequate ventilation must be provided. Avoid positioning ducting or other objects that obstruct the ventilation slots. Avoid mounting modules over heat-generating equipment. Installation in the bottom part of the electrical panel is recommended.
CAUTION
These are open type devices intended for installation in a final casing/panel
that offers mechanical protection and protection against the spread of fire.
FACTORY IP ADDRESS
The default module IP address is static: 192.168.90.101
WEB SERVER
To access the maintenance Web Server with 192.168.90.101 factory IP address: Default user: admin, Default password: admin, http://192.168.90.101
ModBUS CONNECTION RULES
- Install the modules in the DIN rail (120 max)
- Connect the remote modules using cables of an appropriate length. The following table shows cable length data:
- Bus length: maximum length of the Modbus network according to the Baud Rate. This is the length of the cables that connect the two farthest modules (see Diagram 1).
- Derivation length: maximum length of a derivation 2 m (see Diagram 1).
For maximum performance, it is recommended to use special shielded cables, designed specifically for data communication.
USB PORT (Z-4DI-2AI-2DO)
The module is designed to exchange data according to the modes defined by the
MODBUS protocol. It has a micro USB connector on the front panel and can be
configured using applications and/or software programs. The USB serial port
uses the following communication parameters: 115200,8,N,1. The USB
communication port responds exactly like the serial ports, with the exception
of the communication parameters. For more information, visit the site shown on
page 1.
Check that the device in question is included in the list of products supported by the Easy Setup APP in the store.
CONNECTOR IDC10
Power supply and Modbus interface are available using the Seneca DIN rail bus,
via the IDC10 rear connector, or the Z-PC-DINAL-17.5 accessory.
Back connector (IDC 10)
The illustration shows the meanings of the various IDC10 connector pins if
signals are to be sent via them directly.
SETTING THE DIP-SWITCHES
WARNING
The DIP-switch settings are read-only at boot time. At each change, perform a
restart. SW1 DIP-SWITCH:
Through DIP-SWITCH-SW1 it is possible to set the IP configuration of the
device:
RS232/RS485 SETTING: RS232 or RS485 configuration on terminals 10-11-12 (serial port 2)
ELECTRICAL CONNECTIONS
Attention: the upper power supply limits must not be exceeded, as this might cause serious damage to the module. To meet the electromagnetic immunity requirements:
- use shielded signal cables;
- connect the shield to a preferential instrumentation earth system;
- separate shielded cables from other cables used for power installations (transformers, inverters, motors, induction ovens, etc.).
POWER SUPPLY
ANALOGUE INPUTS
Documents / Resources
|
SENECA ZE-2AI Automation Interfaces
Ethernet
[pdf] Instruction Manual
ZE-4DI-2AI-2DO, Z-4DI-2AI-2DO, ZE-2AI, Automation Interfaces Ethernet, ZE-2AI
Automation Interfaces Ethernet, Interfaces Ethernet, Ethernet
---|---
References
- seneca.it/products/z-4di-2ai-2do/doc/CE_declaration
- seneca.it/products/ze-2ai/doc/CE_declaration
- seneca.it/products/ze-4di-2ai-2do/doc/CE_declaration
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>