BRAYER BR1404 STAINLESS STEEL CHOPPER Instruction Manual
- June 4, 2024
- BRAYER
Table of Contents
BRAYER BR1404 STAINLESS STEEL CHOPPER Instruction Manual
The chopper is intended for chopping vegetables, fruit, herbs, onion, garlic, raw or boiled meat, cheese.
DESCRIPTION
- High knives rotation speed on button «H»
- Low knives rotation speed on button «L»
- Motor unit
- Chopper bowl lid
- Chopper bowl
- Knives
- Spatula
SAFETY MEASURES AND OPERATION RECOMMENDATIONS
Read the operation manual carefully before using the unit; after reading, keep it for future reference.
-
Use the unit for its intended purpose only, as it is stated in this manual.
-
Mishandling the unit can lead to its breakage and cause harm to the user or damage to the user’s property, which is not covered by warranty.
-
Make sure that the operating voltage of the unit indicated on the label corresponds to your home mains voltage.
ATTENTION! Continuous operation time of the chopper should not exceed 15 seconds, after that make at least 1 minute break. -
Place and use the unit on a flat dry and steady surface.
-
Use only the removable parts supplied with the chopper.
-
Before switching the chopper on, make sure that all removable parts are installed properly.
-
Before using the chopper for the first time, wash all the removable parts that will contact food.
-
Put the products into the chopper bowl before switching the unit on. Do not switch the unit on if the chopper bowl is empty.
-
Cool down hot products before putting them into the chopper bowl.
-
Watch the amount of products put into the chopper bowl and the level of poured liquids.
-
Before using the unit make sure that the knives are installed properly.
-
The cutting edges of the knives are sharp and dangerous, handle the knives carefully.
-
If the knives stop rotating during the unit operation, switch the unit off, unplug it and remove the motor unit and the lid, remove the product which is hindering the knives rotation. If the knives rotation is hindered, it is recommended to add some water, juice, liquor etc. into the chopper bowl.
-
Remove the motor unit of the chopper only after complete stop of the knives rotation and after the unit is unplugged.
-
Do not use the unit outdoors.
-
It is recommended not to use the unit during lightning storms.
-
Protect the unit from impacts, falling, vibrations and other mechanical stress.
-
Never leave the unit connected to the mains unattended.
-
Do not use the unit near heating appliances, heat sources or open flame.
-
Do not use the unit in places where aerosols are used or sprayed, and in proximity to inflammable liquids.
-
Do not use the unit in proximity to the kitchen sink, in bathrooms, near swimming pools or other containers filled with water.
-
If the unit is dropped into water, unplug it immediately, and only then you can take the unit out of water.
-
Do not let the power cord touch hot surfaces and sharp edges of furniture.
-
Unplug the unit after usage or before cleaning. When unplugging the unit, hold the power plug and carefully remove it from the mains socket, do not pull the power cord, as this can lead to its damage and cause a short circuit.
-
Do not touch the unit body, the power cord and the power plug with wet hands.
-
For child safety reasons do not leave polyethylene bags used as packaging unattended.
Attention!
Do not allow children to play with polyethylene bags or packaging film. Danger of suffocation! -
The unit is not intended for usage by children.
-
Do not leave children unattended to prevent using the unit as a toy.
-
Do not allow children to touch the operating surface, the unit body, the power cord or the power plug during operation of the unit.
-
Be especially careful if children or disabled persons are near the operating unit.
-
During the unit operation and breaks between operation cycles, place the unit out of reach of children.
-
The unit is not intended for usage by physically or mentally disabled persons (including children) or by persons lacking experience or knowledge if they are not under supervision of a person who is responsible for their safety or if they are not instructed by this person on the usage of the unit.
-
From time to time check the power cord integrity.
-
If the power cord is damaged, it should be replaced by the manufacturer, a maintenance service or similar qualified personnel to avoid danger.
-
Do not repair the unit by yourself. Do not disassemble the unit by yourself, if any malfunction is detected, and after the unit was dropped, unplug it and apply to the service center.
-
To avoid damages, transport the unit in the original package.
-
Keep the unit in a dry cool place out of reach of children and disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USAGE ONLY
BEFORE THE FIRST USE
- After the unit’s transportation or storage at negative temperature, unpack it and wait for 3 hours before using it.
- Unpack the unit and remove all the packaging materials.
- Keep the original package.
- Check the delivery set.
- Read the safety measures and operating recommendations.
- Examine the unit for damages, in case of damage do not plug it into the mains.
- Make sure that specified specifications of power supply voltage of the unit correspond to the specifications of your mains. When using the unit in the mains with 60 Hz frequency, the unit does not need any additional settings.
- Wash the bowl (5) and the lid (4) with warm water and neutral detergent, rinse and dry.
- Wash the knives (6) with warm water and neutral detergent, rinse and dry.
- The cutting edges of the knives (6) are sharp and can be dangerous, handle the knives (6) carefully.
- Clean the motor unit body (3) with a soft, slightly damp cloth, and then wipe it dry.
- Do not immerse the unit, the power cord and the power plug into water or any other liquids.
USING THE CHOPPER
-
The unit is intended for chopping vegetables, fruit, herbs, onion, garlic, raw or boiled meat, cheese, ice.
ATTENTION!
Continuous operation time of the chopper should not exceed 15 seconds, after that make at least 1 minute break.
Do not chop very hard products, such as nutmegs, coffee beans, cereals and frozen food. -
Notes: — when using the unit for the first time, a foreign smell from the electric motor can appear — this is normal and it is not covered by warranty.
Before processing the products
- remove bones, fat and sinews from meat, cut the meat, cheese, onion, vegetables and fruit into cubes approximately 1,5×1,5 cm;
- shell the nuts, remove stems from herbs.
Food processing
Use the knives (6) for processing raw or boiled meat, maximal weight for pork: 650 g, for beef: 600 g, the knives (6) are also used for chopping vegetables, fruit, aromatic herbs, onion, garlic, cheese, ice. It is recommended to chop ice in the pulse mode, periodically press and release the on button (1) «H».
- Before assembling the chopper make sure that the power plug is not inserted into the mains socket.
- Place the bowl (5) on a flat dry and steady surface.
- Install the knives (6) on the axis inside the bowl (5). Be careful: the knives (6) are sharp, always hold the knives (6) by the plastic end.
- Put the pre-cut products into the bowl (5).
- Notes:
- do not switch the chopper on if the bowl (5) is empty.
- the amount of food for processing should not exceed 2/3 of the capacity of the bowl (5) and should not be below the blades of the knives (6).
- Install the lid (4) on the bowl (5).
- Install the motor unit (3) on the lid (4).
- Insert the power plug into the mains socket.
- To switch the chopper on press and hold the button (1) «H» — the knives will be rotating at the maximal speed. To switch the low knives (6) speed rotation press and hold the button (2) «L».
- During the operation press the on button (1 or 2) with one hand and hold the bowl (5) with the other.
- Notes: — if food processing is hindered or the products level is below the knives (6) edges, you can add some water, juice, broth etc.
- After using the chopper wait until the knives (6) fully stop rotating.
- Remove the power plug from the mains socket.
- Remove the motor unit (3).
- Remove the lid (4) from the bowl (5).
- Take the plastic end and remove the knives (6) from the bowl (5).
- Take the chopped products out of the bowl (5) with the spatula (7).
CLEANING AND MAINTENANCE
ATTENTION!
The blades of the knives (6) are very sharp and dangerous. Handle the knives
(6) carefully!
- Unplug the chopper before cleaning.
- Remove the motor unit (3).
- Remove the lid (4) from the bowl (5).
- Carefully remove the knives (6).
- Wash the parts (4, 5, 7) with warm water and neutral detergent, rinse and dry.
- Wash the knives (6) with warm water and neutral detergent, rinse and dry.
- Clean the motor unit (3) with a soft, slightly damp cloth and then wipe it dry.
- Do not immerse the motor unit (3) into water or any other liquids.
- Do not use abrasives and solvents to clean the motor unit (3) and the removable parts.
- After processing salty or sour products rinse the knives (6) with warm water.
- After processing products with strong dyeing properties (for instance, carrot or beet-root) the removable parts can get colored. To clean the removable parts wipe them with a dry cloth, dampened in vegetable oil, and then wash them with warm water and neutral detergent, rinse and dry.
STORAGE
- Clean the chopper before taking it away for storage.
- Keep the unit in a dry cool place out of reach of children and disabled persons.
DELIVERY SET
- Chopper assembled — 1 pc.
- Manual — 1 pc.
TECHNICAL SPECIFICATIONS
- Supply voltage: 220-240 V, ~50-60 Hz
- Rated input power: 500 W
- Maximal operation time: — 15 seconds
RECYCLING
To prevent possible damage to the environment or harm to the health of people by uncontrolled waste disposal, after expiration of the service life of the unit or the batteries (if included), do not discard them with usual household waste, but take the unit and the batteries to specialized stations for further recycling. The waste generated during the disposal of the unit is subject to mandatory collection and consequent disposal in the prescribed manner.
For further information about recycling of this product apply to a local municipal administration, a disposal service or to the shop where you purchased this product.
The manufacturer reserves the right to change the appearance, design and specifications not affecting general operation principles of the unit, without prior notice.
The unit operating life is 3 years
The manufacturing date is specified in the serial number.
In case of any malfunctions promptly apply to the authorized service center.
