TELWIN DRIVE 1750 XC Powerbank with LED Light Instruction Manual

: June 13, 2024
: TELWIN

Table of Contents

TELWIN DRIVE 1750 XC Powerbank with LED Light
Product Information
GENERAL SAFETY USER INSTRUCTIONS FOR THIS STARTER
INTRODUCTION AND GENERAL DESCRIPTION
OPERATING INFORMATION
RECHARGING THE STARTER
SPECIFICATIONS
GUARANTEE
CERTIFICATE OF GUARANTEE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TELWIN DRIVE 1750 XC Powerbank with LED Light

Product Information

Product Name: Not provided
Product Manual Language: Multiple languages
Product Usage: Not provided

EXPLANATION OF DANGER, MANDATORY AND PROHIBITION SIGNS

DANGER OF EXPLOSION
GENERAL HAZARD
DANGER OF CORROSIVE SUBSTANCES
DANGER OF ELECTRIC SHOCK
EYE PROTECTIONS MUST BE WORN
Symbol indicating separation of electrical and electronic appliances for refuse collection. The user is not allowed to dispose of these appliances as solid, mixed urban refuse, and must do it through authorised refuse collection centres.

WARNING: READ THE INSTRUCTION MANUAL CAREFULLY BEFORE USING THE STARTER!

GENERAL SAFETY USER INSTRUCTIONS FOR THIS STARTER

In order to reduce the risk of personal injury and damage to equipment, it is highly recommended to comply with all essential safety measures and precautions when using the starter.

Inexperience and untrained people should be properly instructed before using the appliance.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
Protect the eyes. Always wear protective goggles when using acid lead accumulators.
Avoid contact with battery acid. If an operator should be sprayed or come into contact with the acid, rinse the relative parts immediately under clean running water. Continue to rinse the area until the physician arrives.
It is important to connect the cables with the poles in the right direction:

First connect the red clamp to the positive terminal on the vehicle battery (+ symbol). Connect the black clamp to the vehicle chassis, at a distance from the battery and the fuel pipe.

Use the starter in well ventilated areas. Do not attempt to use the starter when there is gas or inflammable liquids in the vicinity.
Make sure that the black and red clamps never come into contact with each other as this could cause them to fuse together or with other metal objects. Return the clamps to their respective housing.
FOR 12 VOLT SYSTEMS ONLY! This device is destined for use on vehicles running on 12 Volt electrical systems only.
USE IN EMERGENCY SITUATIONS ONLY: do not use the starter instead of the vehicle battery. Use it during start-up operations only.
Do not work alone. If there is an accident, the assistant can be of aid to the operator.
Prevent electrical shocks. Be very cautious when applying the clamps to non-insulated – FOR 12 VOLT SYSTEMS ONLY! This device is destined for use on vehicles running on 12 Volt electrical systems only.
USE IN EMERGENCY SITUATIONS ONLY: do not use the starter instead of the vehicle battery. Use it during start-up operations only.
Do not work alone. If there is an accident, the assistant can be of aid to the operator.
Prevent electrical shocks. Be very cautious when applying the clamps to non-insulated conductors or bus bars. Avoid all body contact with surfaces of tubes, radiators, and metal power substations whilst testing the voltage.
Keep the work area clean at all times. Untidy cumbersome areas can lead to injuries.
Protect the starter appropriately from all possible damage. It must only be used as indicated in this Instruction Manual.
Ensure compliance with the indications in the work area. Do not use in humid or wet facilities. Never leave it out in the rain. Always work in well lit areas.
Always wear suitable clothing. Never wear baggy clothing or jewellery that can get caught up in moving parts. During all operations, the use of electrically insulated protection clothing and non-slip boots must be worn at all times. Persons with long hair must tie it back and wear a hair net.
Only experts are allowed to do repair work on the starter as it involves significant risk levels for inexperienced workers.
Replacing parts and accessories. When performing maintenance operations, replace with identical spare parts only. Use of non-original spare parts invalidates all warranties.
Make sure that the device is always positioned in a stable and well supported manner.
Never climb over cables or electrical structures.
Careful attention must be paid during maintaining work on the starter. Check the condition of cables on a regular basis and if any damage is detected, have the same repaired by an authorised and qualified technician.
Check there are no damaged parts. Before using this starter, carefully check that all seemingly damaged parts and assess whether or not they can operate correctly. Check that the cables are securely fastened to the starter. Remember that only authorised and qualified technicians are allowed to repair or replace damaged parts.

SPECIAL WARNINGS AND SAFETY PRECAUTIONS ON THE USE OF THE LITHIUM BATTERIES INSIDE THE STARTER
Failure to observe the following rules can cause breakage, overheating, bulging, fire outbreak or explosion of the battery inside the starter:

Never open the starter casing under any circumstances.
Do not charge the battery in direct sunlight, near flames or in similar conditions.
Do not use the starter or position it in the vicinity of heaters, near flames or in other hot areas.
Only use the charger supplied with the device to charge the starter.
Do not throw the starter into a fire or heat it up.
Do not invert the positive “+” and negative “-” connection polarities.
Do not short-circuit the starter terminals. Do not perforate the starter casing with drill bits, do not hit it with a hammer or stand on it.
Do not position the starter inside stoves, microwave ovens etc.
Do not throw the starter or cause high impacts.
Do not modify or tamper with the starter casing.
Refrain from using the starter and disconnect it from the charger if it emits strange smells, heats up or deforms during use, charging or storage.
If the starter emits strange smells or leaks acid, immediately move the device away from any heat sources or free burning flames.
In case of contact of the starter battery acid on the skin or clothing, rinse with copious amounts of water.
In case of contact of the starter battery acid with the eyes, rinse immediately with copious amounts of water and call a doctor.

Keeping this manual.
The manual should be read, paying attention to all the warnings and safety precautions to be taken when using and maintaining the device, the list of components and all technical specifications. Please keep this manual in a secure and dry place for future reference.

INTRODUCTION AND GENERAL DESCRIPTION

Intended use
Multi-functional, portable, battery-powered starter. Ideal for anyone needing an emergency starter. Its applications include use on motorcycles, engine- operated vehicles, boats and more besides. Fully compatible with any 12-volt starter system. The starter uses LITHIUM BATTERIES; this makes the device extremely compact and easy to handle. The starter is also equipped with a powerful LED light, a USB port type C for charging and output ports (according to model) to power and/or charge 5V/9V/12V/15V/20V electronic devices. The most advanced model allows wireless charging of smartphones equipped with this function.

DRIVE 1250 – 1500 MODELS
Description (figure A):

A-1. Hard book type pack.
A-2. Multi-functional starter.
A-3. Starter clamps.
A-4. Adaptor output cable between USB type A and USB type C.
A-5. USB port type C for starter charging. A-6. 12V/10A jack output for non-standard accessories.
A-7. USB output type A with QC2.0 (5V/9V/12V) and QC3.0 (3.6V to 12V dynamic with 200mV increases).
A-8. LED lights.
A-9. Starter clamps output socket (ref. A-3). A-10. ON/OFF key for the charge level, the output ports (ref. A-7 and 8) and the LED lights.
A-11. Internal battery charge status indicator LED.
A-12. Jack cigarette light socket adaptor with USB outputs type A/C.

DRIVE 1750 XC MODEL
Description (Figure B):

B-1. Hard book type pack.
B-2. Multi-functional starter.
B-3. Starter clamps.
B-4. Adaptor cable between USB type A and USB type C.
B-5. USB port type C for starter charging. B-6. USB output type C with PD (5V/9V/12V/15V/20V).
B-7. USB output type A with QC2.0 (5V/9V/12V) and QC3.0 (3.6V to 12V dynamic with 200mV increases).
B-8. LED lights.
B-9. Starter clamps output socket (ref. A-3). B-10. ON/OFF key for the charge level, the output ports (ref. A-7 and 8) and the LED lights.
B-11. Internal battery charge status indicator LED.
B-12. Zone for wireless charging.
B-13. Jack cigarette light socket adaptor with USB outputs type A/C.

INSTALLATION POSITIONING THE STARTER
When using the starter, position it on a horizontal, flat and stable surface.

OPERATING INFORMATION

How to use the starter:
WARNING: follow these instructions meticulously, and always in the order given below!
Always prevent the black and red clamps from touching each other or a common cable!

Make sure that the vehicle or boat to be started is switched off (switch or ignition key in the OFF position).
Connect the red clamp POS. (+) to the battery terminal POS. (+), then connect the black clamp NEG. (-) to the vehicle chassis or the battery terminal NEG. (-).

WARNING: failure to follow these rules may compromise the operating life of the device:

Turn the vehicle ignition to the start position for no more than 3 seconds.
If the vehicle or boat does not start, wait at least 15 seconds before trying again.
If the vehicle or boat still does not start, wait at least 2 minutes before trying again.

After a successful start, with the engine running, follow the sequence of instructions below with great care:

Disconnect the black clamp (negative) from the vehicle.
Disconnect the red clamp (positive) from the vehicle.
Remove the starter cable connector from the starter
Replace the cables and the starter in their seats inside the case.
It is highly recommended to recharge the starter as soon as possible.

Using the starter as a power and/or charging device

Outputs using USB port type A
- Press the ON key (Fig. A-10, B-10 according to the model).
- The charging status will be displayed (Fig. A-11, B-11) and the outlet USB ports will be enabled.
- Use the output cable (Fig. A-4, B-4) to power/charge the equipment with a USB port type C (Quick Charge enabled).
- Insert the USB A terminal of the cable into the output port on the starter (Fig. A-7, B-7);
- Insert the other appropriate terminal into the device to be powered/charged.
Output via USB port type C (1750 XC model only)
- Press the ON key (Fig. B-10) to enable the output port.
- Use an appropriate USB C output cable (not supplied) to power/charge the equipment equipped with USB C inlet that require PD (Power Delivery).
- Insert the USB C terminal of the cable into the output port on the starter (Fig. B-6)
- Insert the other USB C terminal into the device to be powered/charged.
12V-10A output (1250 – 1500 models only)
- Use an output cable with 5.5mm cylindrical connection (non-standard accessory) to power/charge the equipment with 12V input.
- Insert the power terminal in the output port on the starter (Fig. A-6).
- Insert the other appropriate terminal into the device to be powered/charged.
Wireless charge (1750 XC model only)
- Press the ON key (Fig. B-10) to enable the wireless charge.
- Position the smartphone above the highlighted zone ( ) of the DRIVE (Fig. B-12) and check charging has begun (charge symbols on the display of the smartphone); if necessary, move the phone above the highlighted zone of the DRIVE until the point is found where wireless charging takes place.

Using the LED lights
Press and hold the ON button (Fig. A-10, B-10) for a few seconds to enable the continuous LED light.
Then, press in sequence the key to change the operating mode and obtain:

very intense light;
emergency signalling;
switch off light.

RECHARGING THE STARTER

Important! To achieve maximum battery performance, always charge before use, then after every time it is used and, in any case, at least every 3 months. It is however possible to charge the unit on the vehicle:

connect the jack adaptor (Fig. A-12, B-13) to the cigarette light socket of the vehicle;
connect the starter charging port (Fig. A-5, B-5) to the jack adaptor using the cable in Fig. A-4, B-4.

You can charge the unit using the cable in Fig. A-4, B-4 connecting it to an external power source 5V – 2A.
Press the button in Fig. A-10, B-10 to check whether the battery needs charging. The LEDs in Fig. A-11, B-11 indicate the charge status of the battery, which light up as the status increases:

one LED only: low battery;
all LEDs are on: fully charged battery.

DISPOSING OF THE BATTERY
When the starter battery is completely run down it should be sent to a re- cycling facility. In some countries this is mandatory. Contact the local special refuse authority for information on recycling.

WARNING: Do not burn the battery to dispose of it. This could cause an explosion. Before disposing of the battery, apply insulating tape to the bare terminals to prevent shorting. Do not expose the battery to intense heat or fire as this could cause an explosion.

SPECIFICATIONS

DRIVE 1250

Type of battery: rechargeable factory-sealed lithiumpolymer battery.
Battery capacity: 9000 mAh
Starter current (12 V):
- 350 A
- (1250A peak)
Starter cables:
- polarised terminals
- copper
- diameter 5.3mm2 (10AWG)
- length 250 mm
- PVC insulated
Light: 2 LED, 150Lm.
Input and output ports:
- USB port type C for charging: 5V – 3A max
- output USB port type A: 5V/9V/12V – 18W
- output jack 5.5mm socket: 12V – 10A
Other characteristics:
- ON/OFF switch
- Quick Charge: QC2.0 and QC3.0
- automatic charging level reset switch
- charge level and fully charged indicator LED
- intense LED, less intense and emergency light.
Weight (starter with cables): 530 g
Accessories included (Fig. A):
- Adaptor cable between USB type A and USB type C (Fig. A-4)
- Jack cigarette light socket adaptor with USB outputs type A/C (Fig. A-12)

DRIVE 1500

Type of battery: rechargeable factory-sealed lithiumpolymer battery.
Battery capacity: 12000 mAh
Starter current (12 V):
- 450A (1500A peak)
Starter cables:
- polarised terminals
- copper
- diameter 5.3mm2 (10AWG)
- length 250 mm
- PVC insulated
Light: 2 LED, 150Lm.
Input and output ports:
- USB port type C for charging: 5V – 3A max
- output USB port type A: 5V/9V/12V – 18W
- output jack 5.5mm socket: 12V – 10A
Other characteristics:
- ON/OFF switch
- Quick Charge: QC2.0 and QC3.0
- automatic charging level reset switch
- charge level and fully charged indicator LED
- intense LED, less intense and emergency light.
Weight (starter with cables): – 575 g
Accessories included (Fig. A):
- Adaptor cable between USB type A and USB type C (Fig. A-4)
- Jack cigarette light socket adaptor with USB outputs type A/C (Fig. A-12)

DRIVE 1750 XC

Type of battery: rechargeable factory-sealed lithium polymer battery.
Battery capacity: 12000 mAh
Starter current (12 V):
- 450A
- (1500A peak)
Starter cables:
- polarised terminals
- copper
- diameter 5.3mm2 (10AWG)
- length 250 mm
- PVC insulated
Light: 2 LED, 150Lm.
Input and output ports:
- USB port type C for charging: 5V – 3A max
- output USB port type A: 5V/9V/12V – 18W max
- output USB port type C: 5V/9V/12V/15V/20V
- 60W max
- wireless charge for wireless Smartphones.
Other characteristics:
- ON/OFF switch
- Quick Charge: QC2.0 and QC3.0
- PD: Power Delivery
- automatic charging level reset switch
- charge level and fully charged indicator LED
- intense LED, less intense and emergency light.
Weight (starter with cables): – 585 g
Accessories included (Fig. B):
- Adaptor cable between USB type A and USB type C (Fig. B-4)
- Jack cigarette light socket adaptor with USB outputs type A/C (Fig. B-13)

GUARANTEE

The manufacturer guarantees proper operation of the machines and undertakes to replace free of charge any parts should they be damaged due to poor quality of materials or manufacturing defects within 12 months of the date of commissioning of the machine, when proven by certification. Returned machines, also under guarantee, should be dispatched CARRIAGE PAID and will be returned CARRIAGE FORWARD. This with the exception of, as decreed, machines considered as consumer goods according to European directive 1999/44/EC, only when sold in member states of the EU. The guarantee certificate is only valid when accompanied by an official receipt or delivery note. Problems arising from improper use, tampering or negligence are excluded from the guarantee. Furthermore, the manufacturer declines any liability for all direct or indirect damages. To protect the battery and lengthen its working life, charge it before using it for the first time, then after every time it is used and, in any case, at least every 3 months. If these recommendations are not followed, the battery may undergo an irreversible chemical deterioration process. As the battery is a component subject to wear and tear and its level of performance and preservation over time depend on how well it is used and looked after, this element is not covered by any form of warranty.