Telwin B07TB3MKV2 Welder’s Hood Automatic Welding Helmet Instruction Manual

Telwin B07TB3MKV2 Welder’s Hood Automatic Welding Helmet

WELDER’S HOOD MANUAL

Telwin S.p.A.
Via della Tecnica, 3 – 36030 Villaverla (Vicenza) Italy
This information note must be read carefully before use and before all maintenance.

PPE IDENTIFICATION

ONE SIZE hood in flame retardant (FR) cotton fabric and Kevlar (Dupont) stitching.

WARNINGS

Before use, visually inspect the product to ensure it is in perfect condition. If the product is not intact (torn threading, cracks, smears), it must be replaced, since it complies with safety characteristics only if perfectly worn and in a perfect state of preservation. The equipment must not be worn where there is risk of entanglement caused by moving machine parts.
TELWIN S.p.A. cannot be held in any way liable for any damage and/or consequences resulting from improper use. The garment only provides protection for brief contact with incandescent welded parts and if there are high risks of electric shock further protective layers must be worn.

CATEGORY (Annex I of Regulation (EU) 2016/425): II

STANDARDS and PERFORMANCE LEVELS

The product complies with the following performance requirements summarized in prospectus 3 of standard UNI EN ISO 11611: 2015. – Fabric composition: cotton.

• CLASS 1 ≥ 15 N
• CLASS 2 ≥ 20 N

| Conforming: CLASS 1
6.5 Seam strength| CLASS 1 and CLASS 2 ≥ 225 N| Conforming
6.7 Limited flame spread| CLASS 1 and CLASS 2:

• The flame must not reach the edge
• No hole formation
• No incandescent or melting body
• Flame persistence ≤ 2s
• Afterglow ≤ 2s

| Conforming Code letter: A1
6.8 Impact of splatter|

• CLASS 1 ≥ 15 drops
• CLASS 2 ≥ 20 drops The material must NOT catch fire

| Conforming: CLASS 1
6.9 Heat transfer (radiation)|

• CLASS 1: RHTI 24 ≥ 7.0s
• CLASS 2: RHTI 24 ≥ 16.0s

| Conforming: CLASS 1
6.10 Electrical resistance| CLASS 1 and CLASS 2 > 105 Ω| Conforming

MAINTENANCE INSTRUCTIONS

The product must be kept in its original packaging, in a dry place. Avoid contact with solvents which can cause alterations in the characteristics. In particularly demanding conditions or in environments with special situations, the product may be subject to sudden, unexpected deterioration not planned by the manufacturer.
Fig. A provides the meaning of the maintenance symbols (not applicable if washing is not permitted).

CLEANING

Strictly comply with the instructions on the label/marking of each garment (see Fig. B). Cleaning and/or washing treatments non-conforming with those outlined could alter the dimensions and safety characteristics of the garment. Use suitable cleaning products for the material composing the garment that are free of harmful effects for the garment and the user.

RECOMMENDED USE

The clothing worn in addition to the adequate protective equipment (welder’s helmet, protective jacket, etc.) offers further protection to the head, neck and the upper shoulders in the event of:

• sparks generated by the welding process;
• mechanical risks and thermal risks generated by the welding process.

The level of protection of the garment is reduced in the presence of contaminations of other flammable materials.

The increase in oxygen in the air considerably reduces protection from flame.

This PPE does not protect against:

• chemical attack.
• risk of entanglement caused by parts in motion.
• risks of crossing and extinguishing the flames.
• risks other than those specified above.

The manufacturer cannot be held liable for protection against risks differing from those contemplated in this information note relating to this PPE.

IDENTIFICATION AND CHOICE OF SUITABLE PRODUCT

The responsibility for identification and choice of adequate/suitable product (PPE) is that of the employer and must be carried out based on specific requirements in the workplace, of the risk and the relevant environmental conditions. Suitability must be checked, before use, of the model relating to personal needs.

EXPIRY DATE

In relation to natural wear of the material used to produce this PPE and the resulting reduction in mechanical quality, use is not recommended over 5 years from its manufacture/purchase. Different conditions to those recommended could reduce the life of the product.

IDENTIFICATION OF THE MARKING

A marking is applied to the product, or its interior, in a visible position, containing all the necessary elements to identify the PPE.
Fig. B provides an illustrative example with the following meaning:

1. Manufacturer.
2. Model and composition.
3. CE marking.
4. Reference standard for protective clothing used for welding.
5. Specific pictogram for the protective clothing used for welding.
6. Class and code letter for the performance level of the protective clothing.
7. Max number of washes (if applicable).
8. Read the use instructions.
9. General reference standard for protective clothing.
10. Specific pictogram for size designation (not present if “ONE SIZE”)
11. Size identification.
12. Washing symbols (if applicable).

Note: the exact values must be found directly on the protective clothing.

FIG. A

| Washing in water with detergents permitted. The internal number indicates the maximum permitted washing temperature. One or two lines under the symbol indicate a reduced or greatly reduced mechanical action process.| | Bleaching is permitted with chlorine-based products.
---|---|---|---
| Tumble drying permitted:
••Drying at 60°C Drying at 80°C| | Air drying permitted: Flat Hung In Shade (In top left corner)
| Indicates ironing permitted (max temperature of plate):
•110°C
••150°C
••• 200°C| | Dry cleaning permitted with (insert letter in circle):

• F: hydrocarbons.
• P: hydrocarbons, tetrachloroethylene.

This sign above the symbol indicates it is forbidden to carry out the planned treatment.

WARRANTY

The manufacturer guarantees its products are free of material and processing defects and is committed to undertaking replacement free of charge if products are received with poor quality materials or with manufacturing faults, within 12 months of date of sale, validated on the certificate, in the planned use conditions. Returned products, even if under warranty, should be sent CARRIAGE PAID and will be returned EX-WORKS. An exception to this rule is made for products which fall within the scope of European Directive 1999/44/EC only if they are sold in the EU Member States. The warranty certificate is valid only if accompanied by a receipt or delivery note. Problems resulting from misuse, tampering or carelessness are excluded from the guarantee. In addition, all liability for all direct and indirect damages is waived.

CERTIFICATE OF GUARANTEE

MOD.
NR.
Date of buying
Sales company (Name and Signature)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>