LASERWORLD CS-2000RGB FX MK2 Professional Show Laser Instructions

LASERWORLD CS-2000RGB FX MK2 Professional Show Laser

SOUND-TO-LIGHT

• Sound-to-light operation allows to playback the integrated patterns to the beat of music or any noises.
• Select SoUd” by navigating with the Up* / Down” buttons and confirm with Enter”:
• The standard selection is „ALL”, which means that all patterns saved on the main board are played back.
• You can decide to use only a certain part of the pattern set with a certain grating by selecting ALL (for all the gratings), L001, L002, L003, L004, or no grating with L005:

• To set the sensitivity of the internal microphone, refer to chapter „4.5. Settings”

STAND-ALONE / AUTO

• The stand-alone or Auto operation allows random playback of the internal patterns.

• They are played back according to the internal system settings.

• Select Auto” by navigating with the Up” / Down” buttons and confirm with „Enter”:

• The standard selection is „All”, which means that all patterns saved on the main board are played back. You can decide to use only a certain part of the pattern set with a certain rating by selecting ALL (for all the ratings). L001. L002. L003. L004, or no rating with L005:

MASTER-SLAVE

• This laser is Master-Slave capable. This means that the Master laser system can hand on a control signal to one or more Slave lasers, so all do the same.
• Master-Slave only works with lasers of the same product series of the same product generation.

A: Link lasers with DMX cable

• To use Master-Slave operation, link the Master with the Slave lasers with DMX cables. Make sure to use the „DMX out” port on the Master and the „DMX in” on the Slave lasers. If several
• Slave lasers are used, link the first one to the Master laser and daisy-chain the control signal from the first Slave laser to the second, etc.

B: Activate Master Laser

• The Master laser needs to be set as the control source.
• Select „Set” by navigating with the, Up” / „Down” buttons and confirm with „Enter”:

Manual: CS-2000RGB FX MK2 | CS-4000RGB FX

• Use the Up” / Down” buttons to navigate to „last”

• Press, Enter”, use the „Up* / „Down” buttons to switch the option to„on” and confirm with Enter”

C: Deactivate the Master setting on Slave lasers

• As soon as the Master option is set to on, the laser sends out the control signal for the Slave units. Make sure that all Slave units have the Master setting set to „oFF*:

D: Set Sound-to-Light or Auto mode on the Master laser
To use the Master-Slave operation: set the Master to either Sound-to-Light mode (4.1) or Auto mode (4.2.).
E: Establish a link to Slave lasers
The Slave units must be set to DMX (d512″) mode and must be assigned address 001 (see 4.4. DMX 512)
DMX 512

• The DMX mode requires a DMX controller or a Master laser (see 4.3. Master-Slave operation) to be connected to the laser.

• To switch to DMX mode, select d512″ by navigating with the „Up” / „Down” buttons and confirm with Enter”.

• The submenu for setting the DMX address loads:

• Press, Enter” and the „Up” / „Down” buttons to set the desired DMX address.

• Confirm with „Enter” and press, Exit” to return to the main menu.

SETTINGS

• To access the settings, select, SEt” by navigating with the Up” and „Down” buttons and confirm with Enter*:

• The settings menu holds several configuration options for the laser system.

Manual: CS-2000RGB FX MK2 | CS-4000RGB FX
Machos Catina

• The „AST menu allows for the activation and deactivation of the Master mode for the laser.
• If the laser is set to Master > On, then it can be used as a Master device in a Master-Slave setup. See more in _4.3. Master-Slave*
• Press Enter” to change the settings. Use the Up / Down button to change the selection.

Confirm with „Enter”.
Orientation Setting

• The InuE menu controls the orientation of the projection. You can invert the projection and flip it to match the orientation of the laser with the content.

• Press, Enter” to change the settings. A test picture is shown to represent the currently set orientation. Use the „Up / „Down button to change the selection, and confirm the selection with Enter” to change the test picture projection

• Press, Exit” to return to the settings menu.

Microphone Sensitivity Settings

• The sensitivity of the built-in microphone for the control of the sound-to-light operation can be adjusted in the „SEnS” menu. Press „Enter” to change the settings. Use the„Up* / „Down” button to change the selection.

• The sensitivity can be adjusted between 1 and 100. The standard value is 50.

ILDA / COMPUTER CONTROL

• The laser can be used with any laser control software that supports the ILDA control signal via a sub-d connector. Use an ILDA cable to connect the Digital Analog Converter (DAC / ILDA interface) of the laser software to the ILDA in port at the laser.

• To operate the laser in ILDA mode the „ILdA” menu must be selected. Press Enter” to change the settings.

• Grating Effects Settings In ILDA mode – DMX grating control on ILDA

• Once ILDA mode is selected, the standard selection is L001″, which means that the laser will automatically switch through the grating effects. A certain grating effect can be selected with L002, L003, L004. If L005 is selected there is no grating effect.

• Use the Up” I Down” button to change the selection:

• Select „d512* and press Enter if you want to control grating effects with DMX while working on ILDA mode. You must previously set a DMX address as specified in, the 4.4 DMX 512″ section.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>